Question about Suzuki Cars & Trucks

1 Answer

1995 suzuki sierra. when I turn on the ignition it is bolwing the fuse any ideas

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

Sure lots. (doing this for 50 years)cars, trains, boats and planes.
and ships and avionics and..... yes....

finding this with no tools, is very hard,
i have an amp clamp , DMM ammeter.
it tells me fast, which wire IS shorted. FAST !
lacking tools.
you have a box of fuses and pull connectors
until the blows stop.

a shop also has a circuit beaker tool that replaces the stock
fast action fuse. saving a small fortune if fuse.
here is an example ,not your car, but all cars , you use the same methods, having schematic from alldata dot com ,makes this
10x more easy

find the color wire this is shorted,
now trace that wire, using an ammeter
or the pull and pray way
the color wire , is that wire on the outbound side of said blown fuse.
is this clear.? if not ask, can do this 1 line at a time.
or email
or join my forum. can do all ways.

Posted on Sep 13, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Intermittent problem.Turn key and just get a click. Turn the ignition to aux position and then back truck starts. Any Ideas?

when the problem occur keep ignition key on engine stop. with a test light find out if fuses have all current if not might be ignition switch defect

Oct 07, 2014 | 1997 GMC Sierra

1 Answer

95 Sierra 5.0 TBI Cranks but won't run. Wouldn't crank at all. Replaced fuel pump, filter, ignition module computer and oil pressure sending unit and checked wiring harness. Now it will crank but only...

Just a few ideas without knowing too much about whats going on. Check for spark first, then check to make sure you are getting gas to injectors. Coil pack or rotor could be bad. May be a stupid question, but is the battery good? If battery isn't putting out enough juice then it wouldn't be able to turn over the engine for long to start. Test it with a volt meter (should be around 13 volts) Hope this helps.

Aug 26, 2013 | 1995 GMC Sierra

2 Answers

I have a 1995 GMC Sierra pickup and my tail lights don't work

there is a big green fuse in the fuse box under the hood. cost about 6 bucks. replace that

Jan 30, 2012 | 1995 GMC Sierra

1 Answer

My brakelights work when ignition is off but not when it is on what could the problem be because all other lights work and fuses and relays so im not quite sure

Hello! The Ignition Switch has one set of contacts that power Brake lights, And Heater Blower Motor...It is the Orange wire in the ignition switch plug...Turn on the Blower Fan and turn off the ignition key...Does the blower continue to run? If so the problem is that set of contacts in the ignition switch...
If not, I'll take it from there...Send a comment............Guru..Saailer

I’m happy to help further over the phone at

Jan 19, 2011 | 1995 GMC Sierra C1500

2 Answers

I have A 1991 GMC SIERRA, 350,no fuel no spark, have fuel to the tbi, changed coil, ignition module, tested pick up coil good, check engine light comes on with key, fuses good. I'm running out of ideas....

Do you have power to the injectors? One of the wires to the injector will come on for a couple seconds as soon as you turn the key to the on position.The computer controls the ground side. If you do not get power to one of them start looking for an open circuit. The same power source will also go to your ignition coil and ignition module. If you do not have power on the pink wire to the coil apply a temporary fused battery power source to it and give it a try, this will also power up the injectors.
Check it out and let me know.

Oct 29, 2009 | 1991 GMC Sierra

2 Answers

1995 GMC Sierra truck

It,s very lcd power wire to ignition swiich...then it will only light up when key is on

Jun 18, 2009 | 1995 GMC Sierra C1500

1 Answer

Cant find my turn signal flasher on my 1995 gmc sierra


Jun 10, 2009 | 1995 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides