Question about 1995 GMC Yukon

Open Question

Were is the fuel pump located on a 1995 yukon

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: FUEL PUMP REPAIR

the fuel pump is located inside the gas tank, the gas tank is held in place by 2 steel straps, fule lines, wiring and the filler nect must be disconnected as well, also u MUST replace the fuel filter and the the fuel pump connector at the tank connector, this is the part number for the fuel pump connector.VERY IMPORTANT!
AIRTEX Part # WH3008 {Wiring Harness}
PRICE $10.61, SOURCE www.rockauto.com
lowest prices on the internet i have found.

Posted on Jun 19, 2009

Ad
  • 1596 Answers

SOURCE: have a 1995 gmc yukon 2dr i have change the fuel

On a NO Power to FUEL Pump Problem One Must ALWAYS Start from the Begining of the THAT CURCIUT, This Being the Fuse , Then The FUEL PUMP Relay , And Then WIRING , and LAST Is The PUMP Itself. Here is Info on the RELAY. rejakwilsoin @ aol.com < is my Email Address if you want More info Feel free to Contact me.

The Fuel Pump Relay is located in Underhood Fuse Relay Center. The Underhood Fuse Relay Center is located on the LH rear of engine compartment, on fender.


REMOVE OR DISCONNECT

  1. Protective cover.
  2. Retainer, if installed.
  3. Electrical connector.
  4. Relay by depressing bracket clip at rear of relay, or removing bolts from retaining bracket.
INSTALL OR CONNECT
  1. Relay.
  2. Electrical connector.
  3. Retainer.
  4. Protective cover.

Posted on Nov 02, 2009

Testimonial: "HE WENT ABOVE AND BEYOND WHAT WAS ASKED AND HE GAVE GREAT ADVISE ON THE PROBLEM I HAD "

  • 468 Answers

SOURCE: 1995 gmc yukon i have change the fuel assmbliy

you can manually actuate the relay if you want. Take the cover off, and push the contact over with a screwdriver and see if you can hear the pump. Have you checked to see if there's power to the relay, both the control side and the side providing power to the pump? There's two different circuits involved here, so you have to make sure they're both ok. If you have power before the relay, and power coming out of the relay headed to to pump, then your problem falls between the relay and the pump. Other things to consider, are the fuel pressure sensor, and oil pressure sensor. Some vehicles will not turn the pump on if they sense no oil pressure after a couple of seconds. Secondly, if the fuel pressure sensor is telling the pump that there's plenty of pressure, (even if there's not) it'll shut the pump down. Hope this helps you.

Posted on Nov 07, 2009

Testimonial: "IT WAS GREAT GETTING HELP WITH THIS MATTER "

  • 427 Answers

SOURCE: my 1995 yukon wont stay started!! its getting

fuel pump is faulty

Posted on Mar 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Not getting any power to the fuel pump 1995 GMC Yukon 517 later


If you actually have NO power at the pump and the fuse and relay are good, then there is a break in the wire between the fuse block and the pump but most likely it is a bad fuel pump

Feb 17, 2014 | 1995 GMC Yukon

1 Answer

My 1995 yukon gt went out while i was driving, i replaced the fuel pump and im still not getting fuel to the tbiz. what do you the it mybe or what can i check while trouble shooting.


You may have a bad control module, this controls the injectors and fuel pump, also have you checked for spark,as sometimes you loose the spark also when module goes bad.

Aug 29, 2010 | 1995 GMC Yukon

3 Answers

WHERE IS THE FUEL PUMP FUSE LOCATED


Hi!!

The fuel pump fuse is located in the engine compartment fuel box, located on the center firewall

Don't forget to rate this post!! Good Luck!!

Jul 19, 2010 | 1999 GMC Yukon

1 Answer

1995 gmc yukon i have change the fuel assmbliy


you can manually actuate the relay if you want. Take the cover off, and push the contact over with a screwdriver and see if you can hear the pump. Have you checked to see if there's power to the relay, both the control side and the side providing power to the pump? There's two different circuits involved here, so you have to make sure they're both ok. If you have power before the relay, and power coming out of the relay headed to to pump, then your problem falls between the relay and the pump. Other things to consider, are the fuel pressure sensor, and oil pressure sensor. Some vehicles will not turn the pump on if they sense no oil pressure after a couple of seconds. Secondly, if the fuel pressure sensor is telling the pump that there's plenty of pressure, (even if there's not) it'll shut the pump down. Hope this helps you.

Nov 07, 2009 | 1995 GMC Yukon

2 Answers

Have a 1995 gmc yukon 2dr i have change the fuel assmble the fuel pump the feed line and return line i have no power to the fuel pump anf help your be gratful ......


On a NO Power to FUEL Pump Problem One Must ALWAYS Start from the Begining of the THAT CURCIUT, This Being the Fuse , Then The FUEL PUMP Relay , And Then WIRING , and LAST Is The PUMP Itself. Here is Info on the RELAY. rejakwilsoin @ aol.com < is my Email Address if you want More info Feel free to Contact me.

The Fuel Pump Relay is located in Underhood Fuse Relay Center. The Underhood Fuse Relay Center is located on the LH rear of engine compartment, on fender.


REMOVE OR DISCONNECT
  1. Protective cover.
  2. Retainer, if installed.
  3. Electrical connector.
  4. Relay by depressing bracket clip at rear of relay, or removing bolts from retaining bracket.
INSTALL OR CONNECT
  1. Relay.
  2. Electrical connector.
  3. Retainer.
  4. Protective cover.

Nov 02, 2009 | 1995 GMC Yukon

2 Answers

Is the pump located in the fuel tank on a 1997 YUKON GT 2 DOOR


yes its located in the tak easiest way to replace it is to take bolts out thats holding the bed on and slide bed back and change pump

Oct 10, 2009 | 1997 GMC Yukon

1 Answer

Turns over but wont start, not sure if it is the fuel pump or water in gas


Instances like this is always fuel system related. Consider checking and replacing your fuel pump if need be.

Have a look at the fuel filter too.

Fuel pump is located in the fuel tank while the fuel filter is located in the hood.

Good luck and don't forget to rate this location.

Aug 13, 2009 | 1995 GMC Yukon

1 Answer

Engine will turn over but not start


Yes the pump is electric and its located in the fuel tank. If the pump is getting power and ground, and not coming on it needs to be changed. Use only an OEM pump in this vehicle. Don't use an aftermarket pump.

Dec 28, 2008 | 1995 GMC Yukon

2 Answers

Cuts out when accelerating


Did you change the fuel filter? also did you clean the inside of the MAF sensor w/ MAF spray cleaner?

Oct 29, 2008 | 1995 GMC Yukon

Not finding what you are looking for?
1995 GMC Yukon Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...