Question about Hummer Cars & Trucks

1 Answer

Seat belt not release

Seat belt will not detract, hummer h2 2007, trying to replace

Posted by on

Ad

1 Answer

May need a special socket from Snap-On
to remove the seat belt bolts

Posted on Aug 01, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1999 Dodge 2500 passenger side seat belt wont release

so after completely tearing the seat apart I found 2 wires going up to the seat belt mechanism from under the seat, these wires got caught in the seat mechanism underneath and were shredded. There must be a small solenoid inside the seat belt mechanism because I could hear it click after I repaired the wires(this circuit is live even with the ignition off) Im not sure how it all works but this solved my problem.

Posted on Jun 12, 2008

  • 37 Answers

SOURCE: rear middle seat belt wont retract

Sounds like a mechanicel problem in the belt box. Do you have a guarantee for that car?

Posted on Aug 17, 2009

  • 1 Answer

SOURCE: back seat (middle belt) belt stuck and unable to release.

Hi, We are having the same problem with our son's car. Were you able to come up with a solution?

Posted on Dec 13, 2009

  • 5370 Answers

SOURCE: Passenger Seat belt "frozen on

The seat belt when this happens , the belt will need to be replaced, it is locked inside,

Unsnap the pillar cover, take out a fold in the belt, and carefully snapped cover back on, making sure rubber trim covers the edge.

---

Just pry open the b pillar. You'll see 2 things a bolt up top and the actual seatbelt locking thing.. Just unbolt the top bolt to get some "SLACK" on the belt. Retract it gently then the locking mechanism should release.

Be very gentle with the top trim piece, it comes off ok but on one end the thin plastic lip gets cracked and breaks a little where it sits. ---------- Click this below for more details:--- http://howtobyme.blogspot.com/2011/09/seat-belt-stuck-in-back-position-on-bmw.html ---------- This will help.Thanks.Helpmech.

Posted on Sep 18, 2011

emissionwiz
  • 76630 Answers

SOURCE: seat belt locked

You will need to cut the best and replace it. Seat belts are not repaired, just replaced. Safety and liability issues

Posted on Nov 05, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I change a serpentine belt on my h3 hummer 2008 model 3.7l


It should have the diagram on the front of your hummer underneath the hood look around for the diagram hopes this hel

Jul 23, 2014 | Cars & Trucks

1 Answer

How to replace 3rd row seat drivers side seat belt?


Please bear with me, a lot of people don't know that if this occurs that you must start the vehicle and relax and pull out the seat belt with a firm and steady action but not to pull too fast or no yanking. You must start the vehicle to reset the security system for the vehicles safety belts to release and go back to ready to use mode

May 01, 2014 | 2003 Toyota Sienna

1 Answer

Seat belt locked


You will need to cut the best and replace it. Seat belts are not repaired, just replaced. Safety and liability issues

Nov 05, 2012 | 2006 Pontiac Montana SV6

1 Answer

Drivers seat belt releases spontaniouly


If your drivers seat belt is releasing spontaneously, I would suggest that you replace the seat belt buckle mechanism immediately because, if confronted with an emergency situation, someone could be endanger, like the driver of this vehicle. If you not under warranty, go to salvage yard and find your vehicle and find the seat belt buckle mechanism to replace your current one.

Jan 06, 2011 | 2003 Ford Windstar

1 Answer

The seatbelt sometimes gets stuck and won't release. My kids try to buckle and sometimes it works and other times it doesn't.


Spray a little of WD-40 into the female end of the belt assembly. Wrap it in a clean cloth to prevent over spray, and try working the male end into the female connector. You may have to do this several times to achieve a positive result. Otherwise you may have to replace the entire seat belt assembly.

Sep 14, 2010 | 2006 Hummer H3

1 Answer

Stuck seat belt


Remove the panels to the belt, normally these can miss roll and get stuck. Unbolt the unit so you can get some slack that should be enough to release and pull it back out to correct it. If that will not do it get a replacement from a junkyard and replace.

May 20, 2010 | 1990 Pontiac Grand Prix

1 Answer

Rear middle seat belt wont retract


Sounds like a mechanicel problem in the belt box. Do you have a guarantee for that car?

Aug 17, 2009 | 1996 Toyota Corolla

2 Answers

Rear seat down and wont go back up; locked middle belt


middle seat belt shouldn't have anything to do with it. The seat locks down for stowage in the rear cargo area. you can pull the release handle on the back of the seat to release it back into the up position.

Jul 01, 2009 | 2006 Saturn Vue

1 Answer

Seat belt release


you nee to replace the seat buckle and possible the tensioner/ the seat belt buckle is easy to replace its a torx screw 32 bit take it out and replace /disconnect the battery when removeing/ to check seat belt tensioner pull out see if it goes back like a yoyo and if it does then you may not need the tensioner/ Please rate my response Thank you

Jan 31, 2009 | 2004 Nissan Titan

2 Answers

1999 Dodge 2500 passenger side seat belt wont release


so after completely tearing the seat apart I found 2 wires going up to the seat belt mechanism from under the seat, these wires got caught in the seat mechanism underneath and were shredded. There must be a small solenoid inside the seat belt mechanism because I could hear it click after I repaired the wires(this circuit is live even with the ignition off) Im not sure how it all works but this solved my problem.

May 21, 2008 | 1999 Dodge Ram 2500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...