Question about 2006 Chevrolet Malibu

1 Answer

2006 chevrolet malibu has anti lock brakes but front ones are not hook up i dont know what to do this is dangers for me to drive. just boutht the car help

Posted by on

1 Answer

Don't know what to do,that's odd
You don't have a repair shop you go to
several times a year ?

Posted on Aug 01, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: brake lights stay on

u will need to replace the brake light switch, it is located at the top of the arm the brake pedal is attached to, simple hand tools to replace, very easy job, part very cheap.

Posted on Jun 17, 2009

2coolrick
  • 560 Answers

SOURCE: 2008 chevrolet malibu door lock problem

You have a intermittent condition. To isolate the cause: 1.Disconnect the drivers door lock/unlock switch from the connector. Drive the vehicle and see if your random lock/unlock condition has stopped. If it has, replace the switch. If it hasn't:
2. You have a grounding problem or a problem in the BCM (Body Control Module) and should have a technician use a Tech 2 Diagnostic Link Tool to access the BCM computer to obtain any fault code data to help correct the condition.

Posted on Mar 07, 2010

ZiggynSC09
  • 79 Answers

SOURCE: how do i change front brake pads on 2006 malibu maxx?

You shouldn't need any thing more then a jack, jack stand, 4-way (to remove the wheel) a few wrenches, socket set, large flat head screw driver, a wire brush, metal coat hanger, a small container for bolts and a c-clamp.
You will also want to have some caliper lube, brake parts cleaner, lock-tight(if replacing rotors) & brake fluid; be sure to check the type of brake fluid your car takes. It will be on top of the brake fluid reservoirs cap. It should be DOT3 but could be DOT4. Although most DOT4 brake fluids are designed for DOT3 or DOT4. I always buy DOT4. One last thing you may want is some heavy-duty latex mechanic's gloves they keep your hands clean and protected. Plus you won't be picking grease out of the underside of your finger nails days later.
Buy high quality parts. Remember this is your brakes and your saving money by doing it yourself. You like stopping don't you? So fork out the extra on a better set of pads. I prefer and try to use nothing but Wagner ThermoQuiet Ceramic Disc Brake Pad. I have never had any complaints. They don't over heat fast like all cheap pads out their. They are very quiet. They don't make your wheels turn black. You get 3 times the life. They usually cost around $50.00. So they are well worth the extra money. Advance and Bumper to Bumper sell them.
First do one side at a time DON'T RUSH. Place the car on a hard level surface. A small trick is before jacking turn the wheel toward the side you are about to work on. Place the jack under the car and find a safe place on the car to use as a lift point. Jack until the jack is just lifting the car then break the wheel lug nuts loose. DON'T take them off yet just turn them counter clock wise about 3/4 of a turn.
Now jack the car until the tire is a few inches off the ground. Place the jack stand under the car in a safe location. Now lower the car until the car just touches the jack stand. Make sure your tire is still off the ground. Now remove the lug nuts & wheel. Place the wheel off to the side and the lug nuts in your container.
<u>Top off you brake fluid before counting.</u>
Now if you have a big enough c-clamp place it on the caliper like in the image. If its not big enough just continue.
fa46ccf.gif
<u>This step is important this will prevent damage to you abs system!</u>
Break the bleeder screw loose (be careful if needed tap the caliper with hammer while trying to loosen the screw) Once fluid dribbles from the screw it's loose enough don't remove the screw.
If you don't want a mess click here to learn how to make a brake fluid catch can. You could just use a drain pan but you will most likely make a small mess.
If your c-clamp didn't fit skip this step:
If your c-clamp fit you should now tighten it until the caliper puck is completely back into the caliper. This is done by hand once the c-clamp quits turning you should be good. Don't use a wrench for leverage. If it doesn't turn by hand your caliper maybe stuck. This would require replacement. Now that the piston in all the way back tighten the bleeder screw.
If your c-clamp fit skip this step:
Take your large flat head screw driver and place it into the hole shown in the image. (make sure the bleeder is open)Get the tip of the screw driver on the rotor then pry back. This should create some space between the pads and the rotor. This will help get the caliper off.
d66689f.png
Check your brake fluid DON'T LET IT GO EMPTY. If you had the big c-clamp the bleeder should be closed now. If you had the small one the bleeder should still be open. So keep an eye on the fluid level.
Now you can remove the caliber mounting bolts (shown in the image above). To do this you may need to use a two wrenches or a wrench and a socket. The caliper bolts, bolt in to the slides. When loosening the bolts it's possible for the slides to turn with the bolt. To prevent this just use a wrench on the hex part of the slide. Also loosen one bolt a couple turns then remove the other bolt. Then go back to the first one and remove it. Don't try to remove one bolt with out the other being loose. Be sure to place the bolts in the container.
Take your coat hanger, using the hook part hang it from the spring, then pull down on the bottom to stretch the hanger. Remove the caliper and hang it from the coat hanger. Make sure not to put much pressure on the brake lines (i.e. pulling on, hanging on or dropping the caliper) the brake line isn't that strong and will break.
Now pull out the pads and remove the slides. Remember witch slide came from the top and witch from the bottom. They should be different. One will have a rubber ring on the end. Then place them in you container. Use the wire brush to clean the contact points were the pads were. Use a rag and brake parts cleaner to clean the slides.
If you had the big c-clamp skip the step:
Take one of the old brake pads, place it on the caliper puck then install the c-clamp as shown in image. Tighten down c-clamp using your hand only until it stops. Don't use a wrench for leverage. If it doesn't turn by hand your caliper maybe stuck. This would require replacement. Once the puck is pushed all the way in, tighten the bleeder screw in. Now you can put the c-clamp off to the side and trash the old pads.
07b7281.jpg
If you plan to replace the rotors. Witch is a good idea sense rotors now a days are to thin to turn 99 out of 100 times. Also I believe GM said not to turn their rotors. Just replace them. They have become cheap. Think of it as insurance you don't want to re-due this job in a few months, because of a shake when you hit the brakes, Right?. Remove the two bolts on the caliper mounting bracket. Be sure to loosen one of the bolts a little (about three turns) then remove the other, then go back to the first to remove it. You may need a large strong arm to do this. Put you bolts in your container. Once the bracket is removed take off the rotor. Open the box with the new rotor then remove the rotor from the plastic. The new rotor is coated in oil for shipping to prevent rust. So you need to get all of it off. Spray the rotor down with brake parts cleaner. Then use a rag to wipe it down. You may need to do this a could of times. Now install the new rotor then the caliper mounting bracket. I always use some lock-tight on the caliper mounting bracket bolts. I have seen them come loose. So use a little blue lock-tight and torque these two bolts down.
Take the new pads and install them. Apply some caliper lube to the slides. Install the slides back in the mounting bracket. Reinstall the caliper. When tightening the caliper bolts be ready with a wrench to keep the slides from turning.
Install your wheel and tighten the lug nuts. Lower the car and move over to the other side. Follow the same steps on that side.
Once the brakes are on both sides, the wheels are tightened and the car is down. Recheck the brake fluid. Then pump up the brakes. Then recheck the brake fluid. If you fail to perform this last step of pumping up the brakes you will have NO BRAKES! Also be sure to recheck the fluid before and after. If not you could get air in the line. That will cause weak brakes.

<u><b>Torque</u></b>

* caliper to bracket bolts - 26Ft.-lbs
* caliper bracket to knuckle - 85Ft.-lbs


This is information only; Brakes should be replaced or repaired at a certified shop. Brakes installed by unqualified persons should be inspected by a qualified mechanic before driving the vehicle.

Posted on Apr 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 chevrolet malibu find out my anti lock brakes had been cut none on front what do i do . does this mean i have brakes or what will a booster help this or what do i do please help


If you have no front brakes working, check master cylinder fluid level .If full replace master, if fluid low or empty check for broken line or leaking caliper..if your anti lock light is on but brakes are working ok your anti locks will not work but regular brakes will be ok. If this was helpful please leave good feed back.

Aug 02, 2013 | 2006 Chevrolet Malibu

1 Answer

2006 chevy maxx diagram front wheel bearing hub with abs


my car is a 2006 chevrolet malibu has anti lock brakes they are not hook up on front wheels i have problems with brakes how danagers is this and what do i do

Mar 05, 2013 | 2006 Chevrolet Malibu Maxx

1 Answer

Abs brake bleeding


Here's how to abs bleeding?

Feb 20, 2013 | 2006 Chevrolet Malibu

1 Answer

Changed front rotors/brakes and back drums on 2006 toyota tundra front wheel drive V8, but still have pulsing during braking


Then the job either wasn't done correctly or you have
ABS System problems

You need professional tools to work on ABS

Oct 08, 2012 | Cars & Trucks

1 Answer

Loud noise on my front left side when i brake on my 2006 cobalt


Please have the front wheels pulled and have the brake pads inspected, it sounds like one is worn completely out, this is dangerous.

Sep 06, 2012 | 2006 Chevrolet Cobalt

1 Answer

I just replaced both front calipers on a2006 chevrolet malibu 2.2L, and i need to know the brake bleeding procedure?


Bleed the master cylinder first,then the right front,and the left front.Now only pump brake pedal one time all the way to the floor,

Aug 21, 2010 | 2006 Chevrolet Malibu Maxx

1 Answer

Anti lock break light on how much is it generaly for front sensor


This could be caused by a fuse being blown or this could mean that your brakes need to be changed.

Jul 08, 2009 | 2003 Chevrolet Malibu

4 Answers

Shaking while braking at speeds 40 mph +


Anti-lock brakes mean the car shakes when the brake is applied. Try pumping the brakes.

May 15, 2008 | 1996 Chevrolet Classic

Not finding what you are looking for?
2006 Chevrolet Malibu Logo

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...