Question about 1999 Chevrolet K2500

Open Question

1999 GMC P.U. crank/no start/PO463 code/I can hear fuel pump w/key on

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
psds4
  • 293 Answers

SOURCE: 1997 Chev Cavalier hard starting

it sounds like the check valve in the fuel pump is letting the fuel bleed back into the tank

Posted on Sep 23, 2008

Ad
  • 1 Answer

SOURCE: 1999 CHEVY WONT START

i had th same problem and what fixed my problem was the regulator

Posted on Nov 04, 2008

GM Elec
  • 1000 Answers

SOURCE: 1999 GMC Suburban 350 wont run

Per your description, it sounds like you are missing an injector pulse from the ECM.
Check the under-hood fuse box and verify the "ECM1" fuse is good (12 volt supply to injectors).
With the key in the run position, verify you have 12 volts at an injector.
Barrow or purchase a "noid" light to verify you have an injector ground pulse from the ECM.
Let me know what you find and we can proceed from there.
Regards,

Posted on May 07, 2009

  • 553 Answers

SOURCE: 1999 GMC Suburban turns over but won't start

It sounds like the choke is the most likely culprit. Take the air cleaner off the throttle body/Carburater. Have someone cover most of the throttle body/Carburater intake, if you don't have help use a piece of heavy cardboard. If it starts up right away it's the choke. Note: if you use cardboard don't rev the engine you may **** the cardboard into the engine.
I'm afraid with all the different types of choke controls I can't tell you how to fix your choke with out actually seeing it.

Posted on Jun 06, 2010

  • 834 Answers

SOURCE: 1999 silverado 4.3 cranks but

First check to see if full battery voltage is even getting to the "Pos" (+) positive side of the ignition coil when the key is in the "Run" position, and also that full battery voltage is getting through the "Pos" (+) or positive side of the ignition coil and over to the distributor ignition module

The ignition module and the pick-up coil/stator located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil, and a faulty ignition module can cause any one of these systems to malfunction.

That does sound like a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores. If the ignition module does test out alright then the problem could still be in the pick-up coil/stator, (it can be tested using an ohm meter by dis-connecting the wire connector from the pick-up coil/stator and the ohm reading between the two wires from the pick-up coil/stator should be between 500 and 1500 ohm's, and both of the wires from the pick-up coil/stator should show an open loop or an infinite reading between each wire and ground) and if the pick-up coil/stator is found to be faulty then replace the entire distributor, or the distributor will have to be dis-assembled to install a new pick-up coil/stator.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

To replace the distributor follow this procedure;

The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.

There is a mark or notch on the distributor housing that the rotor should be pointing to when the engine is on top dead center. This "static" timing is all that matters and the computer will be able to control the timing as long as the ignition rotor is in that position when the engine is at top dead center.

Removal;

1. With the engine at top dead center.

2. Look under the distributor cap and find where the number one terminal runs under the distributor cap, and where that position on the distributor cap corresponds with the distributor housing, and it should match up to a mark or a notch on the distributor housing indicating the number one position.

3. With the engine on top dead center the ignition rotor should be pointing to the number one mark or notch that is on the distributor housing, Then make a reference mark of the position that the ignition rotor is pointing to (out on the engine or firewall) and the more precise you mark the position, the easier the installation of the new distributor will be. This will be reference mark #1.

4. Remove the distributor lock down bolt, (the lock down clamp will most likely be attached to the distributor and if so it should not be removed from the distributor) then slowly lift up on the distributor about three inches and note the direction that the ignition rotor turns, and when the ignition rotor stops turning then mark the position that the ignition rotor is pointing to (out on the engine or firewall) and then lift the distributor striaght up and out, and remove the gasket or any left over gasket material from the intake manifold. The more precise you mark the position the easier it will be to install the new distributor and an assistant might be helpful. This will be reference mark #2

Once the distributor has been removed it is important that the engine does not get cranked over by the starter or the crankshaft turned at all, or the reference marks will become useless.

Installation;

Be sure that the new distributor is complete with a new module and that there is a new gasket in place on the distributor.

1. Lower the distributor with gasket down into the distrbutor well and align the ignition rotor with the #2 reference mark and when the distributor gear engages the drive gear on the camshaft then the ignition rotor should turn to the #1 reference mark as the distributor sets all the way back down flush on the intake manifold.

2. Install and tighten the lock down bolt, and If the distributor is properly installed then the ignition rotor should be pointing to the #1 reference mark and the #1 position on the distributor housing with the engine on top dead center.

Replace the distributor cap and connect the spark plug wires, and see if the engine will start, if the engine does start and the check engine light does not come on (assuming that it was not on before) then the distributor is properly installed and there is no further timing requirements.

Let me know if you require any further assistance.



a4e111e.jpg

71a37c7.jpg

91bcf9e.jpg

Posted on Jul 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 gmc 2500hd that cranks but won't start any idea what's wrong have no codes


Check fuel pressure may be low first turn key to on position do you hear fuel pump running should run for approx 10 to 15 sec then stop

Feb 15, 2015 | GMC Cars & Trucks

1 Answer

Starting issues


Yes, the crank shaft position sensor tells the engine when to send fuel and spark to the cylinders in conjunction with the camshaft position sensor. If the crank sensor isn't working properly, the engine doesn't know when do do anything. Depending on what the other codes where, I'd highly suspect the CPS. It's not terribly hard to get at nor expensive of a part, but you will need a diagnostic scanner capable of doing a Crankshaft Learn procedure.

Jan 13, 2014 | 1999 GMC Jimmy

1 Answer

1999 gmc sierra 2500 6 liter ran out of gas now won't start


If you are at or near the 100,000 mile mark then your fuel pump may have failed. If you remove the fuel filler cap and listen carefully at the filler neck while someone turns the ignition key to "run" [don't actually crank the engine] you should be able to hear the fuel pump buzz for about a second and a half as the key is turned On. If you don't hear the pump buzz then odds are your pump is dead. Your pump may have actually failed making it appear as though you ran out of fuel. Not to uncommon. Hope this helps and good luck!

Nov 01, 2011 | 1999 GMC Sierra

1 Answer

My 1999 gmc truck with v8 350 moter will only start with starting fluid


It is very common that the fuel pump goes out on these. Try a fuel pressure gauge to check, or have someone put their ear close to the fuel tank when you turn the ignition switch forward (Not cranking) You should hear it cycle on for about 5 seconds

Jul 01, 2011 | 1999 GMC Sierra

1 Answer

1999 GMC Suburban K2500 7.4L 4x4 starting problems


I the fuses and relays are good for the pump it could be a bad pump especialy if you was having starting problems make sure you have power to the pump. Also do this before changing pump. Put your key in turn it on dont start wait 10 mins remove key wait 10 seconds repeat this a total of 3 times. If that dont work try a different key do the same thing. This relearns your key to the ignition it started with Gm cars and trucks from 1999 to to 2006. It is a big problem but there is no recall that I know of. If that dont work a dealer needs to probably replace and reprogram your ignition switch and keys

Dec 27, 2009 | 1999 GMC Suburban

3 Answers

99 yukon 180,000 mi. doesn't start. cranks forever, but won't start. Should I be able to hear the fuel pump when I turn on the key?


yes you should be able to hear the fuel pump run for about 5 seconds once the key is turned to the on pos. check to make sure you have spark. if you do try having someone spray air intake or carb cleaner into intake manifold while you crank. If the truck starts right up for a second (or stays running as you keep spraying) Id say you have a bad fuel pump and id change the sending unit also. (First check the fuel pump fuse and fuel pump relay) GMC and Chevy are nororiously known for having bad fuel pump/sending unit problems. I have prob changed over 60 myself.

Nov 30, 2009 | 1999 GMC Yukon

1 Answer

No start-95 safari


Could be fuel pump, is the pump running when you turn key on, you should be able to hear it. You are likely going to have to take it to someone with a pressure gauge to make sure it is getting proper fuel pressure. Fuel pumps commonly go on these vehicles

Sep 17, 2009 | 1997 GMC Safari

1 Answer

I have a 1999 Gmc Jimmy and it wont start. It turns over you spray some starting fluid stuff in it and it fires up but then dies. We changed the throttle body sensor the crank sensor. Can anyone tell us...


Sounds like a bad fuel pump. If you turn the key on and don't hear it run, it is the most likely cause. You may be able to smack the tank and get it working again, but will need to be replaced. If not, look for power and ground at the pump connector when key is on.

Jun 29, 2009 | 1994 GMC Jimmy

2 Answers

1999 GMC Suburban Wont Turn Over


It sounds like you have a security problem, I had the same thing it would fire and run for half of a second and then that was it if anything at all. Had the security system rebooted, now it starts and runs fine.

Jun 07, 2009 | 1999 GMC Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...