Question about Cars & Trucks

1 Answer

How to unbolt a good set of heads whats the seqence

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 30 Answers

Hay thats not that hard to do all you have to do is remanber to start in the midel of the head an working youer way out to the end of the heads an chriscorring bake an forth as you go along t.there it not that mush to as you will see ones you get started doing it i hope this help u

Posted on Aug 01, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

I need to know how to install the cylinder head properly on my lexas ls 400

You could go to and search for "Torque Head Bolts".
They have a lot of those there.
Hope this helps.

Mar 22, 2015 | Lexus LS 400 Cars & Trucks

1 Answer

Holden vectra 2.2 head torqure seqence

Removal is no sequence. To Tighten start at the closest one to the center of the head then the one across from it, then the one on the other side nearest the first bolt. Now working in a crisscross pattern work your way outward from the center.

Jul 26, 2012 | Holden Vectra Cars & Trucks

1 Answer

What are the seqence and torque specs. on a 1999 dodge ram 1500,318?

The torque values are 85 ft/lbs. Tighten the bolts in at least three stages, the first tightening should be 30 ft/lbs and then at least twice at the full torque of 85 ft/lbs.

There are ten head bolts and the order is as below:-


Feb 03, 2011 | 1995 Subaru Legacy

1 Answer

Torque in a 97cadi heads?

use new bolts step 1 30 ftlbs
step 2 70 degrees
step 3 another 60 degrees
step 4 another 60 degrees
190 degrees total for the m11-10 bolts
the m6-3 bolts 106 inch lbs
tighten in seqence
<-----front rear bank
----->front bank

Jul 16, 2010 | 1997 Cadillac DeVille

1 Answer


No real trick to it, you get them from underneath. You can unbolt the coils from the module or remove the module first then unbolt the coils. The coils are held on with 5.5mm headed bolts.

May 13, 2010 | 1996 Chevrolet Beretta

1 Answer

Need plug wire seqence and timeing deegree

the power contro module which is the computer sets your timing always. plug sequence is on the plenuem and coil pack

Jan 10, 2010 | 1992 Ford Taurus

1 Answer

What is the code when you change oil on 1994 volvo turbo 850. because you need a code to programe it please. thanks

you only need it to reset service light just change oil and filter as normal then refer to manuel on seqence to set light or take car to dealer who will do it for you will not effect running of car if light is on it is just to tell you service is due

Jan 06, 2010 | 1994 Volvo 850

1 Answer

How to install twin kadrons on a stock 1600 and do i need to install anything else first

fuel pressure needs to be between 1.5 and 2 psi (after the fuel filter) unbolt the throttle cable and remove all hoses from the existing carb. remove the air cleaner. unbolt the intake from the heads and from the exhuast. remove the whole assembly from the vehicle. go ahead and set your valve clearances. plug the preheat hole in the exhuast manifold. install the studs on the intake. apply a little oil on the mating surfaces then apply the gasket, install the carb onto the manifold and the manifold onto the head. do the same for the other side. install the linkage and filter. set the jets all the way in on both sides then back them out two full turns and that should get you to where you can start it. then sync and adjust them accordingly.

Jul 08, 2009 | 1998 Volkswagen Beetle

2 Answers

How to replace viscous assembly

i had a similar problem, my viscous coupling was knocking, when i looked it had broken away from the coupling, but was spinning round and knocking against the floor, i unbolted propshaft from rear, unbolted from the front, you need to use torx head socket. then unbolted middle brackets, (very heavy now, you will need some one else to help) and off it comes, i have been driving it now for 6 months with just front wheel drive.

Apr 30, 2009 | Land Rover Freelander Cars & Trucks

1 Answer

Oil leak

If by head covers you mean valve covers this is an easy fix just install a new set of valve cover gaskets, as this is a fairly common problem ( valve cover gaskets ). Just unbolt the valve covers and remove them then scrape off the old gasket and install the new ones and bolt the covers back on. This is a pretty easy job and the gaskets are less than $ 25.00. If it is the oil pan gasket you will needto drain the oil and unbolt the oil pan and remove it then clean off the old gasket and install the new one.

Oct 07, 2008 | 1992 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15427 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides