Question about Cars & Trucks

Open Question

Ford bantam rear wheel stub axle nut torque - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: changing front wheel bearing

first take the wheel off
Then take the caliper off the rotor
Then take the rotor off the CV joint spindle
You will need to remove the three bolts that hold the bearing in place.
You will either need to remove the two bolts that hold the strut or
you will need a Puller.

Posted on Apr 01, 2009

Ad
warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

canbruce75
  • 1776 Answers

SOURCE: I need the torque spec for the axle and the axle

Go to the autozone.com website and register there. It doesn't cost anything and you will have access to an online repair manual for the vehicle. (Kinda handy) They have a specification section, so the torque specs might be found there. Hope this helps and best wishes.

Posted on Aug 18, 2009

Testimonial: "hey thanks for the help"

  • 599 Answers

SOURCE: 2005 Chevrolet Silverado 1500HD 4 wheel drive

177 ft lbs

Posted on Dec 09, 2009

roniecon
  • 6826 Answers

SOURCE: Replaced rear axle pinion bearing and seal, need

There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace cv joints


Hi Douglas, I'm glad to help. My first suggestion is to get to complete shaft. This way you want have any problems later on. It's not that much more expensive and you'll be glad you did. Below is the procedure for replacing them.



FRONT DRIVESHAFTS

REMOVAL
  1. Raise vehicle on jack stands or centered on a frame contact type hoist. Refer to Hoisting in the Lubrication And Maintenance section of this manual for the required lifting procedure to be used for this vehicle.
  2. Remove the cotter pin and nut lock Hub And Bearing To Stub Axle Retaining Nut from the end of the stub axle.
  3. Remove the wheel and tire assembly from the vehicle.
  4. Remove the wave washer Wave Washer from the end of the stub axle CAUTION: Wheel bearing damage will result if after loosening hub nut, vehicle is rolled on the ground or the weight of the vehicle is allowed to be supported by the tires.
  5. With the vehicle's brakes applied to keep hub from turning, loosen and remove the stub axle to hub nut.
  6. Remove the two front disc brake caliper to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts
  7. Remove the disc brake caliper from the steering knuckle. Caliper is removed by first rotating top of caliper away from steering knuckle and then removing bottom of caliper out from under machined abutment on steering knuckle Brake Caliper Mounting To Steering Knuckle
  8. Support disc brake caliper assembly by using a wire hook and suspending it from the strut assembly Correctly Supported Disc Brake Caliper Do not allow the brake caliper assembly to hang by the brake flex hose.
  9. Remove the brake rotor from the hub and bearing assembly Remove/Install Brake Rotor
  10. Remove nut attaching outer tie rod end to steering knuckle Removing Tie Rod End Attaching Nut Nut is to be removed from tie rod end using the following procedure, hold tie rod end stud with a 11/32 socket while loosening and removing nut with a wrench.
  11. Remove tie rod end from steering knuckle using Remover, Special Tool MB-991113 Tie Rod End Removal From Steering Knuckle Arm
  12. Remove the steering knuckle to ball joint stud, clamping nut and bolt Control Arm To Steering Knuckle Attachment from the steering knuckle.
  13. Using a pry bar, separate steering knuckle from ball joint stud Separating Ball Joint Stud From Steering Knuckle Note: Use caution when separating ball joint stud from steering knuckle, so ball joint seal does not get cut. NOTE: Care must be taken not to separate the inner C/V joint during this operation. Do not allow driveshaft to hang by inner C/V joint after removing outer C/V Joint from the hub/bearing assembly in steering knuckle, end of driveshaft must be supported.
  14. Pull steering knuckle assembly out and away from the outer C/V joint of the driveshaft assembly Steering Knuckle Separation From Driveshaft
  15. Support the outer end of the driveshaft assembly. Insert a pry bar between inner tripod joint and transaxle case Disengaging Inner Tripod Joint From Transaxle Pry against inner tripod joint, until tripod joint retaining snap ring is disengaged from transaxle side gear.
  16. Hold inner tripod joint and interconnecting shaft of driveshaft assembly. Remove inner tripod joint from transaxle, by pulling it straight out of transaxle side gear and transaxle oil seal Tripod Joint Removal from Transaxle When removing tripod joint, do not let spline or snap ring drag across sealing lip of the transaxle to tripod joint oil seal.
INSTALLATION
  1. Thoroughly clean spline and oil seal sealing surface, on tripod joint. Lightly lubricate oil seal sealing surface on tripod joint with fresh clean transmission lubricant.
  2. Holding driveshaft assembly by tripod joint and interconnecting shaft, install tripod joint into transaxle side gear as far as possible by hand Tripod Joint Removal from Transaxle
  3. Grasp inner tripod joint an interconnecting shaft. Forcefully push the tripod joint into side gear of transaxle, until snap ring is engaged with transaxle side gear. Test that snap ring is fully engaged with side gear by attempting to remove tripod joint from transaxle by hand. If snap ring is fully engaged with side gear, tripod joint will not be removable by hand.
  4. Clean all debris and moisture out of steering knuckle, in the area were outer C/V joint will be installed into steering knuckle.
  5. Ensure that front of outer C/V joint which fits against the face of the hub and bearing is free of debris and moisture before installing outer C/V joint into hub and bearing assembly Outer C/V Joint Inspection
  6. Slide drive shaft back into front hub and bearing assembly. Then install steering knuckle onto the stud of the ball joint assembly Steering Knuckle Separation From Driveshaft
  7. Install a new steering knuckle to ball joint clamping bolt and nut Control Arm To Steering Knuckle Attachment Tighten the clamping bolt and nut to a torque of 135 N·m (100 ft. lbs.)
  8. Install tie rod end into steering knuckle. Start attaching nut onto stud of tie rod end. While holding stud of tie rod end stationary using a 11/32 socket, Removing Tie Rod End Attaching Nut tighten tie rod end to steering knuckle attaching nut. Then using a crowfoot and 11/32 socket Torquing Tie Rod End Attaching Nut , tighten the tie rod end attaching nut to a torque of 54 N·m (40 ft. lbs.)
  9. Install braking disc on hub and bearing assembly Remove/Install Brake Rotor
  10. Install disc brake caliper assembly on steering knuckle. Caliper is installed by first sliding bottom of caliper under abutment on steering knuckle, and then rotating top of caliper against top abutment Brake Caliper Mounting To Steering Knuckle
  11. Install disc brake caliper assembly to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts Tighten the disc brake caliper assembly attaching bolts to a torque of 22 N·m (195 in. lbs.)
  12. Clean all foreign matter from the threads of the outer C/V joint stub axle. Install the washer and stub axle to hub/bearing assembly nut on stub axle and securely tighten nut.
  13. Install front wheel and tire assembly. Install and tighten the wheel mounting stud nuts in proper sequence until all nuts are torqued to half the required specification. Then repeat the tightening sequence to the full specified torque of 135 N·m (100 ft. lbs.)
  14. Lower vehicle.
  15. With the vehicle's brakes applied to keep hub from turning, tighten the hub nut to a torque of 244 N·m (180 ft. lbs.) Torquing Front Stub Axle To Hub Nut
  16. Install the spring wave washer on the end of the stub axle.
  17. Install the hub nut lock, and a new cotter pin Hub And Bearing To Stub Axle Retaining Nut Wrap cotter pin prongs tightly around the hub nut lock as shown in Hub And Bearing To Stub Axle Retaining Nut
  18. Check for correct fluid level in transaxle assembly. Refer to Group 21, Transaxle for the correct fluid level checking procedure for the type of transaxle being checked.
  19. Set front toe on vehicle to required specification.

May 07, 2014 | 2000 Dodge Caravan

2 Answers

Rear wheelbearings keeps on humming. this is the third set in a year. whe have fitted new locknuts, is there a spesific torque on the bearings, and is there anything i can do to reduce the noise


how tight do you have these???torque?? never heard of tourquing wheel bearing nuts...all we ever did was put the bearings in the wheel hub..mount it on the axle shaft..rotate the hub while tightening the first nut by hand until thers no slop in the hub(it does not shake on the axle shaft) it turns firmly and smoothly.then put the star nut and cotter lock pin on.. (older cars) if youre torquing these thats putting those new bearings in a bind.. heating them up and making them fail due to excessive heat and wear..are the bearing surfaces gualded now? the whole assembly is damaged and total replacement is required..I hate to say this at the risk of making you mad.. but seriously if you dont know what you are doing exactly.. get some guidance from your parts store they can give you specific instructions on these proceedures and if torquing is called for it will be in/on thoise instructions..

Dec 24, 2013 | 2005 Ford Bantam 1.3i

1 Answer

How do you remove the rear hub nut on a 2004 ford f450 need to get to axle seal


Remove the bolts or nuts at the end of the axle and remove the axle from the axle tube. There will be a little gear lube that will come out that you will need to replace before you use the vehicle again after you replace the wheel seal. That will expose the axle nuts to the axle hub that you will need to remove to replace the inner wheel seal. It's basically very simple once you get the axle out you will see how it all comes apart. Be sure to torque the axle nut and locking nut correctly upon reassembly.

Dec 31, 2010 | 2004 Ford F150

1 Answer

How to disassemble the rear end in a 2000 gmc yukon and how to remove axles


Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Loosen the lug nuts on the wheel and tire assemblies but do not remove the lug nuts
  3. Raise and support the vehicle
  4. Remove or disconnect the following:
    • Wheel and tire assemblies
    • Axle lubricant into a suitable container
    • Rear driveshaft
    • Parking brake cable
    • Brake calipers
    • Shock absorbers from the axle brackets
    • Vent hose from the rear axle vent fitting
    • Nuts and the washers from the U-bolts
    • U-bolts, spring plates and spacers from the axle assembly
  5. Lower the axle assembly from the vehicle
To Install:
  1. Place the rear axle assembly under the vehicle
  2. Align the rear axle assembly with the springs then connect the spacers, spring plates and the U-bolts to the rear axle
  3. Raise the rear axle assembly into position
  4. Install or connect the following:
    • Washers and nuts to the U-bolts; Torque to: 59 lb-ft. (80 Nm) then, Torque to: 89 lb-ft. (120 Nm)
    • Vent hose to the rear axle vent fitting
    • Shock absorbers to the rear axle
    • Brake calipers (See: Brake Caliper)
    • Parking brake cable (See: Parking Brake Cable)
    • Rear driveshaft (See: Rear Driveshaft)
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  5. Fill the rear axle with lubricant
  6. Bleed the brake system (See: Brake Bleeding)
  7. Install the wheel and tire assemblies
  8. Lower the vehicle to the ground
  9. Torque lug nuts as follows:
    • Single Wheel: Torque to: 140 lb-ft. (190 Nm)
    • Dual Wheel: Torque to: 175 lb-ft. (240 Nm)
  10. Road test the vehicle to check performance
prev.gif next.gif

Aug 03, 2010 | 2000 GMC Yukon XL

1 Answer

Wheel bearing


the rear bearing is pressed into the hub so take the hubs off and take to a engineering shop to have the new one pressed in ,now the front ones are similar in as much as they need pressing in and out ,DO NOT TRY TO DO IT WITH A BIG HAMMER ,its dangerous ,remove the wheel trim and slacken the big nut in the middle ,think its a 32mm then jack vehicle up remove the wheel ,undo the brake caliper by the 2 bolts that hold it to the stub axle ,slacken bolt on track rod end but do not remove fully and then wack the end of the stub axle where the track rod end goes through .One good wack with a 1kg hammer will do it on the end of the steering /stub axle shaft without damaging anything because you have left the nut on loose.then remove the bottom track control arm pinch bolt it has a star head and a 17 mm nut on the other end ,use a lengh of scaffold pole or a big crow bar to pull the track control arm down so the ball joint come apart ,take the stub axle off and in the back is a big circlip but leave it alone and just take it to the engineering shop ,its very dangerous to try to remove the bearing with a big hammer and drift because it can and will chip and hit you in the face trust me on this

May 27, 2010 | 2007 Ford Focus (3 Door) Hatchback

1 Answer

Does anyone know the torque wrench settings for the rear hub/wheel bearing nuts on a 2002 Peugeot 206 1100cc please? Also the road wheel bolts?


Tightening torque for the hub nut is 200Nm and the road wheels are 85Nm

NOTE: The rear wheel bearings are remowned on these cars for sticking to the stub axle quite badly, and often have to be forced off using a slide hammer on the drum, it is quite common to end up damaging the wheel bearing, so be prepared to replace this as well in this event

Jan 23, 2010 | 2005 Peugeot 405

1 Answer

Keeps chewing wheel bearings


I'm not familiar with the style of this rear bearing, there are 3 basic designs that are generally used. The single most important thing to consider when installing any of them is preload torque. Obviously the bearing must be properly lubricated and protected with new seals when installed, but the whole job comes down to how tight that big gland nut is when you finish the job. Because the Festiva is really a Mazda, I would cross check the final installation torque of that nut between different spec sheets and see if some answers can be found there.

Mar 12, 2009 | 1991 Ford Festiva

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...