Question about Cars & Trucks

Open Question

Bypass factory amp for BMW 328i - Cars & Trucks

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MrScary66613
  • 1990 Answers

SOURCE: AMP BYPASS

You should be Able to Bypass the Factory amp and Relocate the Speaker Wires to the New Amps and be Fine. Let me Know if you need More Help! Please Rate my Response, I need all the Help That I can Get! Thanks!

Posted on Jan 27, 2009

Ad
ZJLimited
  • 17970 Answers

SOURCE: BMW 328i Starter how to replaice

1999 BMW 328I 2.8L EFI DOHC 6cyl

Starter - Removal & Installation

The starter motor on some models is very difficult to see from the top of engine compartment as it is covered by the intake manifold. On these models, without removing the intake manifold, the starter motor must be removed from underneath the vehicle. Because the starter motor mounting bolts are not easy to access, a long extension with a universal joint mounted on a proper sized socket could be used. A three foot transmission extension is commercially available from tool vendors that has a 3 / 8 inch drive of the driven end and 1 / 2 inch drive on the drive end. If used with a non-binding impact universal joint and a proper fitting impact socket, the starter motor fasteners can be removed from underneath the vehicle.
Once the starter motor fasteners are removed, the starter motor may have to be moved side-to-side several times to loosen the dowel pin if it has corroded in place.

NOTE When the battery is disconnected, the radio code, on-board computer and clock settings will be lost. The radio code should be obtained before disconnecting the battery or radio. Once the battery has been reconnected, the radio will not function unless the code is keyed in.
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm) Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) E36 6-Cylinder Engines
Automatic Transmission Models

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Remove the climate control air intake duct at the rear of the engine compartment as follows:
    1. Release the grille clips at the rear and lift the grille upward from the rubber seal, then remove the seal.
    2. Remove the two self tapping Phillips screws from inside the duct to release the electrical harness housing.
    3. Press the electrical housing downward to expose and remove the two hex head self tapping screws on each side of the duct and lift the duct up and out of the engine compartment.
  5. Remove the intake manifold trim and valve cover trim covers.
  6. Disconnect the ignition coil electrical connectors and ground straps, label for reinstallation and place aside.
  7. Remove the two fasteners that secure the fuel injection electrical connector harness to the rail. Remove the harness and carefully place aside toward the back of the engine compartment behind the right side strut tower.
  8. Remove the intake manifold.
  9. Remove the electrical leads from the starter motor and place aside.
  10. Remove the starter motor mounting fasteners at the transmission bell housing, then remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket, then lift the starter motor upward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.
Manual Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Raise and safely support the vehicle.
  5. Remove the fasteners for the reinforcement mounted between the frame rails just behind the rear lower control arm bushing brackets. Mark the bar-s direction for proper reinstallation and remove the bar.
  6. Remove the fuel line cover located near the left side rear lower control arm bushing bracket.
  7. Release the fuel lines and reverse light wiring from their routing brackets.
  8. Note the routing of the starter motor electrical wires, remove the wire mounting nuts, and place the wires aside.
  9. Remove the top and bottom starter motor to engine-transmission mounting fasteners.
  10. Remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket and carefully lower the starter motor downward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.

Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor

cd45991.jpg

Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts

2cbfa11.jpg

I hope help you with this (rated this help) Good luck.

Posted on Sep 22, 2009

  • 1 Answer

SOURCE: 1997 bmw 328i conv.

radio does not work on my 1997 bmw 328 it gives the message
"phone" a mechanic pulled it out of its slot and reset the code...it worked for two days and again it doesnt work with same message

Posted on Sep 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 BMW 328i keys were stolen a long time ago I need to bypass the security system and ignition swtch to get it to start and drivehow do i do this?


go to dealer with vin number and proof of ownership have keys cut using vin the reason its a security system is so it cant be bypassed

Aug 25, 2015 | BMW Cars & Trucks

1 Answer

Where is the factory amp located ?


In the trunk up next to wheel wells. Start peeling carpet out of the trunk walls and you will find it. The rear speaker wires run right to it.

Please beware that only the 10 speaker systems have a factory amp. The stock 6 speaker systems run straight off of the factory radio. You can buy a factory amp bypass harness for this model at any good car audio shop.
Please find my answer helpful. 25079973-u40lsvyytnuesyuv3fbafhtd-2-0.jpg

Sep 08, 2014 | 1997 BMW 318

1 Answer

Where is the fuse for the air pump and what amp for 328i 96 bmw


I do not know of an "Air Pump" for a 1996 328i. Did you mean
fuel pump (15A fuse # 18) or
blower motor (30A fuse # 20)

Sep 07, 2014 | 1996 BMW 328i

1 Answer

Bmw diagram


Need radio make and model as not all BMW's have the same radio fitted .

May 25, 2014 | 1996 BMW 328i

2 Answers

No sound output in 2000 BMW 328i 4dr Sedan but radio functions properly?


Hi Toxey.

Does your trunk amplifier got power.
basically amp need remote power input it is coming from your radio.
please check when you turn on the radio remote power must turn on.
if no it is radio problem or wire is damaged itself.
please check the outputs,speakers with multimeter or single 1.5v cell.
if power is ok.and the remote on signal is ok your device still not working , it is the problem with power amplifier unit.

please check and let us know the status.
regards.
nuwan

Jan 20, 2014 | 2002 Chrysler Town & Country

3 Answers

1996 bmw radio code input


after entering the code hold downthe fm buttom for 5 sec.

Jun 27, 2009 | 1996 BMW 318

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...