Question about 2005 Ford Explorer Sport Trac
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Flex Fuel sensor Truoble Code
If your flex fuel sensor is bad there is a product on the market that is a much better alternative compared to purchasing a new sensor for over $600 or even a used one for typically around $300. The product is called a Flex Fuel Sensor Replicator made by T&S Electronics and can be purchased off their website www.tandselectronics.com. The cost of the Replicator is $150 and it is very simple to install. In fact, your old flex fuel sensor stays in place so you don't have to mess with your fuel line. The wiring from the original flex fuel sensor is hooked up to the Replicator which sends an electronic signal to your engine control unit that "replicates" the signal the ECU would get from the original FFS when you are burning standard unleaded gasoline containing up to 10% ethenol.
The only limitation present with the Replicator installed is that you can no longer burn E85 or other alternate fuels (no big deal for most people). And, as an advantage you should see a 1-2 mpg improvement with the Replicator installed.
Check out www.tandselectronics.com for more information or contact us via e-mail at firstname.lastname@example.org.
Posted on Oct 08, 2008
your code is or the following. Fuel Pump Secondary Circuit Malfunction. This may involve removing your gas tank to fix. Go to the parts store and they can get you the parts you need and let you know for sure.
Posted on Jun 29, 2009
SOURCE: 2007 Ford expedition won't start
ur oil pump may be failin-there r sensors everywhere on new cars-keepin u from starting as safety measure-computer systems r complex n things dont always show on 1 scan-they kinda hav the mindset of a pc
Posted on Sep 15, 2009
Testimonial: "Thank you. I have spoken with 2 other mechanics who said the same thing regarding the oil pump. It's being looked at. So I'll post more once I know"
SOURCE: I am having two issues
P0302 code is a mifire for cyl #2, Check the ignition coil for the number 2 cylinder.
P0715 Turbine Shaft Speed Sensor Circuit Malfunction - With Automatic Transmission
Possible Causes Setting Conditions
* TSS connector is damaged (check pins for damage, and for moisture)
* TSS signal circuit is open, shorted to ground or shorted to voltage
* TSS has failed
* PCM (Powertrain Control Module) has failed
To test the ignition coil for the P0302 code
Turn the ignition OFF
Disconnect the negative battery cable.
Disconnect the wiring harness from the ignition coil.
Check for dirt, corrosion or damage on the terminals and repair as necessary. Measure coil primary resistance between ignition coil pin 4 (B+) and pins 1 (coil 2), 2 (coil 3) and 3 (coil 1)Resistance should be 0.3-1.0 ohms. If resistance is out of specifications, replace the coil pack. If resistance is within specifications, proceed to secondary windings testing.
Posted on May 04, 2011
SOURCE: 2003 ford focus 2.0L everytime
It sounds like you are losing your Keep Alvie Memory when you turn the key off. There should always be power to the PCM.
OBD Inspection Maintenance (IM) Readiness indicators show whether all of the OBD monitors have been completed since the last time KAM or the PCM DTC(s) have been cleared. Ford also stores a P1000 DTC to indicate that some monitors have not completed. In some states, it may be necessary to perform an OBD check in order to renew a vehicle registration. The IM Readiness indicators must show that all monitors have been completed prior to the OBD check.
Keep Alive Random Access Memory (RAM) The PCM stores information in Keep Alive RAM (a memory integrated circuit chip) about vehicle operating conditions, and then uses this information to compensate for component variability. Keep Alive RAM remains powered when the ignition switch is off so that this information is not lost.
I can see pins 71 & 97 at the PCM supply battery power to the PCM. There may be another pin that supplies power at all times but I can't find it right now. You need to find the pin that is powered to the PCM with the key off, and make sure it's got power with the key off.
Posted on Jul 02, 2011
Tips for a great answer:
Dec 11, 2014 | 2000 Ford Taurus
Mar 04, 2013 | 2000 Ford Ranger SuperCab
Nov 08, 2012 | Cars & Trucks
Nov 05, 2012 | 2000 Ford Taurus
Feb 06, 2012 | Ford F-150 Cars & Trucks
Jul 29, 2010 | 2000 Ford Mustang
Feb 05, 2010 | 2002 Ford Taurus
Sep 14, 2009 | 2002 Ford Taurus
13 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: