Question about 2005 Ford Taurus
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
couple things could had appened first the cruise control module or cru may have went out could be a malfuntion in the with some speed sensors or the vaccum lines have gotten to dry rotted to do the job necessary to maintain the speed
Posted on Mar 24, 2009
clock spring in the steering column is my guess. They are delicate and have to do with anything in the steering wheel like airbag, horn, or anything that is operated by buttons on the wheel. These wires have to turn constantly with the steering wheel and the "clock spring" goes bad often enough
Posted on Jul 08, 2009
Try pulling up the brake pedal with your foot,Sometimes your brake doesnt come back all the way,and the brake switch keeps the cruise from working.Also,check the fuse.If those answers dont help,It could be the swith itself is bad.Those can be bought at a parts store.
Posted on Jul 26, 2009
First the vehicle has to be operating at least 35mph. There will be two sets of switches, one set is to the left and the other set is to the right of the horn on the steering wheel. The switches on the left will be labeled on/off, the ones on the right we be labeled Coast/Accel/Resume..
At a steady highway speed press the ON switch, (at the left hand side of the horn) This will activate and turn the speed control system ON...
Then you have to set and adjust your desired speed...
To SET YOUR DESIRED speed , press and hold the accel switch (Right side of Horn) until your desired speed has been reached and then release the switch.. Speed control will now be on, activated and set, you will be in cruise mode..
If you need to coast due to possible traffic, press and hold the coast switch as long as you need to.. This is like taking your foot off of the accelerator pedal.. When you let go of the coast switch you will return to you set cruising speed.
Stepping on the brake pedal at any time will deactivate the system.. If you step on the brake, and then want to return to your previous set cruising speed... All you have to do is press resume...
I hope this has helped you? You can find detailed speed control activation instructions in your 2005 Ford Focus Owners manual.. If you did not receive your owners manual when you bought the vehicle.. You can purchase one at your local Ford, Lincoln or Mercury dealership..
Bill Andrade Ford Master Technician/Shop Foreman
Posted on Sep 22, 2009
Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.
It could be a blow fuse in the recall harness, if you did have it done.
Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in teh recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked.
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.
1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.
2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.
If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.
The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.
There will be a slight delay when the last button is pressed and the lamp flashes.
3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.
If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:
— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).
Posted on Feb 23, 2010
Tips for a great answer:
Aug 15, 2014 | 2003 Ford Focus
Apr 30, 2013 | 2006 Ford Focus
Aug 06, 2012 | 2005 Ford Focus
Feb 07, 2012 | 2005 Ford Ranger
Jul 21, 2010 | 2005 Ford Mustang
May 27, 2010 | 2005 Ford Focus
Sep 22, 2009 | 2005 Ford Focus
69 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: