Question about 2006 Chevrolet HHR

Open Question

Remove fuse box to get to replace master cylinder

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is required to replace a fuel pump relay in a 2003 Ford Explorer?


In the under hood fuse box, beside the master cylinder. The fuel pump relay location number is 50B, in the same box also check fuse # 23 which I believe is a 20 Amp Mini fuse for fuel pump power.

Feb 09, 2017 | 2003 Ford Explorer

1 Answer

1995 e150 ford van fusebox location


You can access the fuse panel through the steering column lower opening. Remove the cover using the quick release fasteners. 2. On the fuse panel cover, find the number of the fuse you want to check. The diagram on the cover tells you where to locate the fuse on the panel. 3. Check the fuse to see if it is blown. Look through the clear side of the fuse to see if the metal wire inside is separated. If it is, the fuse is blown and should be replaced. There also is a fuse box under the hood by the break Master Cylinder

Aug 03, 2016 | Ford Cars & Trucks

1 Answer

How to remove clutch master cylinder at gearbox


the clutch master cylinder is on the fire wall at the pedal. The slave cylinder is on the gear box bell housing and in some cars it is now inside the bell housing which necessitates the gearbox removal to replace it.. Removal of an external cylinder is to loosen the hose fitting ,unbolt the slave cylinder and then un-csrew the cylinder off the hose

Jan 06, 2015 | Cars & Trucks

1 Answer

How to reset the abs light


Usually when you bleed brakes you must disable abs by removing it's fuse from fuse box. Maybe it's still not in place and giving you the light. Not sure if it's related to that but it would be the first thing I would look into.

Nov 27, 2013 | Cars & Trucks

2 Answers

My clutch seems to have gone out tonight. The clutch is very easy to push to the floor...and it pops back....there's no pressure at all. The clutch fluid is leaking from the hose. Could this be the...


it could be either the master cylinder or the slave cylinder,it could also be the clutch pressure plate check the master & slave cylinders first because if it's the pressure plate the gear box will have to be removed to replace the pressure plate, even if you are uncertain it is most likely cheaper to replace the master & slave cylinders than it would be to replace the pressure plate.....hope this helps......cheers.

Aug 31, 2011 | Saturn Vue Cars & Trucks

2 Answers

When driving and applying the brakes pedal goes to the floor brakes do stop but no peddle . looking for a diagram of the fuse boxes and such


perhaps the master cylinder is sick put a little pressure on the pedal and keep your foot on the pedal just to keep it hard a little if the pedal goes down slowly the it s the master

Jun 19, 2010 | 1995 Ford Ranger Supercab

1 Answer

How to change a master cylinder


a Master rates about a 5 out of 10 with 10 being the hardest

you may find the hardest part is the actual bench bleeding of the master
and/or
the replacement of the reservoir

These are the instructions from my service manual, but I do not remove the fluid prior to service steps 2-6

  1. Disconnect battery ground cable. Disconnect electrical connector from filler cap.
  2. Remove fluid reservoir filler cap.
  3. Raise and support vehicle.
  4. Remove front wheels.
  5. Remove dust cap and loosen bleed nipple. Connect a bleed tube to bleed nipple and into a suitable container.
  6. Pump brake pedal until all fluid is expelled. Tighten bleed nipple.
  7. Lower vehicle. Install brake fluid reservoir cap. Remove air cleaner and air cleaner outlet tube.
  8. Disconnect central electrical box electrical connector.
  9. Remove central electrical box retaining screw.
  10. Remove central electrical box and relocate to air cleaner area.
  11. Disconnect brake fluid feed tube. Disconnect brake lines.
  12. On models with anti-lock brakes, disconnect brake lines from Hydraulic Control Unit.
  13. On all models, remove brake booster vacuum hose.
  14. Extract master cylinder from vehicle.
  15. On models with manual transaxles, remove clutch hose from brake/clutch reservoir.
  16. On all models, remove master cylinder nuts and remove master cylinder.

To install, reverse removal procedure. Bleed brake system.

May 31, 2010 | 2001 Ford Focus

1 Answer

Where is the fuse for the fuel pump located?


its located under the hood in the fuse/relay box, remove cover, under cover on the back is a diagram of which fuses are were, you will see the fp/inject fuse thats for the fuel pump and injectors and there is also a pump relay in there as well, hope this helps
this fuse box is on the driverside next to master cylinder under the hood.

Dec 13, 2009 | 2003 Pontiac Grand Am

1 Answer

Do you have instructions on removing and replacing master cylinder in 1993 GMC Sierra K3500 pickup?


REMOVING
Removing the master cylinder is really simple, only requiring a few steps. Keep in mind that brake fluid will eat the paint of the car. So use a plastic or vinyl type fender cover to protect the vehicle's paint. Brake fluid is water soluble so if you should get some on the paint, wash it off with plenty of water as quickly as possible.
  1. Using a siphon, an old turkey baster works great, empty the master cylinder reservoir and dispose of the old brake fluid in the proper manner.
  2. Disconnect the wire connector for the brake fluid level and/or brake pressure-warning switch, if your vehicle is so equipped.
  3. Disconnect the brake lines from the master cylinder with a line wrench. A line wrench is specially designed to remove and install hydraluic fittings without rounding them off.
  4. Remove the master cylinder mounting nuts, then the master cylinder.
  5. On non-power brake vehicles, disconnect the master cylinder linkage from the brake pedal underneath the dash.
  6. On models with separate fluid reservoirs, remove the reservoir.
REPLACING
Before installing the new master cylinder on the vehicle, it must first be bled using a specialized bleeder kit. The master-cylinder bleeder kit comes with tubing, clips and multiple adapters. Most new or rebuilt master cylinders come with a bleeder kit for that particular master cylinder.
  1. Begin by removing the cap.
  2. Follow the directions that come with the kit to select the suitable adapters, and then connect the adapters and tubes to the ports on the cylinder. The other ends of the tube extend down into the master cylinder, and are held in place by a plastic clip. Figure 2.
  3. With the bleeder kit installed, fill the master cylinder about halfway with new brake fluid. Use a large screwdriver to depress the valve assembly inside the master cylinder. If you do not have a vise you can mount the master cylinder on the vacuum brake booster and bleed the master cylinder.
  4. Small bubbles will appear in the fluid. Continue working the valve assembly until no more bubbles appear. This indicates that the cylinder has been thoroughly bled.Reverse the removal procedure to install the master cylinder, noting the following Refer to your service manual for any Master Cylinder Push Rod Adjustment procedures if your vehicle requires it.Bleed brakes as described under Brake Bleeding.Operate the brakes several times and check for external hydraulic leaks.This is fairly straightforward job. Replacing a master cylinder should take you about 1 to 2 hours, depending on the make and model of car. If you are rebuilding the master cylinder, add about another hour or so.

Oct 12, 2009 | 1993 GMC Sierra K3500

1 Answer

Windows want unlock,and inside lights want come on. help where are the fuses located in the box for these problems.


The fuse panel is located under the left side of the dash behind a removal panel by the steering wheel. There is also a fuse box in the engine compartment by the master cylinder. I would check all the fuses while you are in there.

Jun 13, 2009 | 1998 Ford Expedition

Not finding what you are looking for?
2006 Chevrolet HHR Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...