Question about Chrysler PT Cruiser
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Hi, i have put together a step by step guide that will help you with this replacement job. Make sure the vehicle is in a cool state before starting this job.
* Drain some coolant into a clean container until the coolant level is below the thermostat housing.
* Remove the upper radiator hose connection from the thermostat housing.
* Loosen the housing bolts and remove the housing.
* Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
* Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
* The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
* When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
* Install the gasket.
* Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
* When the engine has reached operating temperature make sure the thermostat opens.
* You should be able to see coolant circulating within the radiator.
* Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
* If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.
When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.
Posted on Apr 30, 2009
Here are my photos what you need to open when replace plugs&wires:
Posted on May 31, 2009
check to see if the serpantine belt is still there. It sounds like like it broke. this belt runs all of the accesories on the vehicle including the water pump. So if this happened it probably starting running hot too
Posted on Jun 23, 2009
Asked under 2001 Category for a 2002 Question.
Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 2002 Chrysler PT Cruiser 2.4L DOHC In-Line 4-Cylinder Engine with the Engine Options (AC/No AC etc.). It also has Instructional and Directional Diagrams inorder to remove and/or replace the Belt(s).
Note: the differences between the Automatic Tensioner and those Tensioners with Adjusting/Locking Bolts/Nuts
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!
Posted on Apr 03, 2010
Tips for a great answer:
Sep 12, 2016 | 2007 Chrysler PT Cruiser Base
Dec 30, 2015 | 2002 Chrysler PT Cruiser
Oct 10, 2014 | 2002 Chrysler PT Cruiser
Sep 09, 2010 | 2002 Chrysler PT Cruiser
Jun 05, 2010 | 2002 Chrysler PT Cruiser
Dec 06, 2009 | 2002 Chrysler PT Cruiser
Jul 08, 2009 | 2002 Chrysler PT Cruiser
Jun 05, 2009 | 2002 Chrysler PT Cruiser
Dec 03, 2008 | 2002 Chrysler PT Cruiser
41 people viewed this question
Usually answered in minutes!