Question about GMC Sonoma
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 94 GMC sonoma needs head gasket
no real pit falls just drain coolant remove head have head checked at machine shop. Clean engine surface good and rise good with brake clean, make sure head gasket is on correct before head goes on bolt down with proper torque and sequence then finish up then drain oil.
Posted on Jan 17, 2009
no fuel shut off switch on pickups that i know of possibly bad fuel pump find your red bypass wire at relay to test pump
Posted on Mar 29, 2009
If the dash is removed you've saved about 9 10ths of the job endurance. Look around, what you believe to be, the perimeter of the heater box. I cannot, and no one else can, tell you exactly where the bolts and nuts that mount the heater box are. Therefore you must viually sixe the box and check outide in the engine compartment and inside under the dash for the mounting bolts.You'll want to start by removing the heater hoses. Then starting at the passenger side engine compartment look for a group of 10mm or 7/16ths nuts retaining the housing and remove them. Do the same inside. The housing is usually held together with screws or clips, it changes year to year. Keep a log or pix of the wires and cables and hoses(vacuum) that are connected to the housing for reassembly. You'll need to "roll" the box out from under the dash depending on how much of the dash has been removed. The core is easy to spot for is has two hoses sticking out, and, is encircled with clips or screws . Also make sure you remove the bracket around the two entry hoses if it has one. Thank you, Dana
Posted on Oct 04, 2009
Removal & Installation
2-Wheel Drive - 2.2L Engine
Negative battery cable Front exhaust pipe, if necessary for access Starter heat shield, if equipped Brace rod from the front of the engine and the bell housing Drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well Wires from the starter solenoid Attaching bracket-to-engine mount bolt Starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you. Starter and shims (if equipped) from the vehicle Bracket from the starter assembly, if equipped
Fig. Starter motor and related components - 2.2L engine
Bracket to the starter, if removed. Tighten the bracket nuts to 97 inch lbs. (11 Nm). Starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position. Bracket-to-engine mount bolt (loosely), if equipped Starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm) Wiring to the solenoid Brace rod and tighten the retainers Front exhaust pipe and tighten the fasteners, if removed Starter heat shield, if equipped Driver-s side wheel, if removed Negative battery cable
Hope helped with this (remember rated this help) Good luck.
Posted on Nov 18, 2009
Tips for a great answer:
Aug 20, 2016 | GMC Sonoma Cars & Trucks
Nov 28, 2015 | GMC Cars & Trucks
Mar 08, 2014 | GMC Sonoma Cars & Trucks
Apr 03, 2011 | 1997 GMC Sonoma
Sep 03, 2010 | 2000 GMC Sonoma Extended Cab
Jun 09, 2010 | 2000 GMC Sonoma Extended Cab
Feb 07, 2010 | 2000 GMC Sonoma Extended Cab
Oct 06, 2009 | 1996 GMC Sonoma
Aug 01, 2009 | 2000 GMC Sonoma Extended Cab
Jun 12, 2009 | 2001 GMC Sonoma Extended Cab
70 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: