Question about 2010 GMC Terrain

Open Question

Hazard lights won't work when the button is pressed? Could this be a fuse issue, where would that be located?

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hazard lights on my 2000 volvo s40 won't turn off please help pressed switch couple of times only turns off while you hold the button in


Sounds like a sticky/bad switch. You can try rapidly pressing the hazard button numerous times to see if switch will release. Usually it will. If not, you can pull the fuse for the hazards (location and identification in owners manual)

May 23, 2015 | 2000 Volvo S40

1 Answer

Turn signal & hazard light switch


does all else work? car run and drive and head lamps work at same time, yes,then you blew the turn/haz fuse in the fuse box.
the operators guide answsers were those are. read it.

Dec 21, 2013 | 1988 Honda Prelude

2 Answers

Chrysler Vision hazard light


on some of these models, the hazard switch operates through its own flasher fuse. if this is the case, locating and replacing the fuse ($4) should do it. Location should be in the owners manual.

Nov 10, 2013 | 1997 Chrysler LHS

1 Answer

I have a 1998 Chevy Z71 and I broke my hazard light button. My hazard lights won't go off so I had to pull the fuse out but now I don't have brake lights or turn signal lights. What should I do?


Pull the wires off the back of your hazard button ,isolate them with tape or terminal block until you replace your broken hazard button. Replace the fuse you took out.

Nov 10, 2012 | Cars & Trucks

1 Answer

1992 Ford Ranger Turn signal/Hazard light issue


Can you just check to make sure the ignition key switch is not staying over to far and not backing off when you try to start it. I had a truck that did that and it messed up my turn signals until I brought the key switch back a little after starting it. Just a simple idea. Be kind with your rating for me. Raz

Apr 19, 2010 | 1992 Ford Ranger

1 Answer

Hazard lights wont come when you push hazard button turn signals will not work push it again and they work


it sounds like the relay has gone for your hazard lights, when you press the button to turn them on, it will disconect the power to the main indicators hence wont work when hazards pused in, try locating either the hazard flasher unit, or the relay , have you checked the fuses?

Feb 01, 2010 | 2000 Hyundai Elantra

2 Answers

Hazard button and door lock button not working 325i 02


Your vehicle only has fuses behind the glove box. But since your central lock button is also inop. The your solution is to replace the switch assembly, it comes with both the hazard switch and the lock/unlock button. The removal of the switch assembly is pretty simple. it just pops up with some plastic body tool to pry on it.

Apr 01, 2009 | 2002 BMW 3 Series

2 Answers

Turn signal


The wire under the hazard button has probably come loose. Most GMC vehicles this year range were made with a closed circuit wiring between the flashers, hazard lights, and rear defrost. Over time the wiring under the hazard button has been known to loosen. This causes the whole system to lose function. If pop out the hazard button on you center console you should be able to tighten that wire back on and the system should work again.
The same thing happened to me when I put in a new radio. I bumped the wires off and my blinkers, rear defrost, and hazard lights went out. I replaced the fuses and the flasher relay but nothing. Then I asked a mechanic and he told me what I just told you.
Hope it helps!

Nov 04, 2008 | 1997 Geo Prizm

1 Answer

2003 Dodge Stratus Hazard Light problem


I had the same issue with a 2002 stratus, the problem was the flasher relay. It's located inside the steering column, inside the multiswitch, and its fairly easy to replace. Two screws under the steering column to remove the top cover, then two hex screws to remove the multiswitch, then you can remove the relay which is green, mine was part# 04606478AD. You won't find this exact relay at the local auto parts store, but you can order from mopar parts online, or check the parts dept. at your local dealer. I called a local dealer, he didn't have it but was able to find one a few miles away, cost was $30.

Aug 23, 2008 | 2003 Dodge Stratus

Not finding what you are looking for?
2010 GMC Terrain Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...