Question about Cars & Trucks

Open Question

Timing marks on toyota 2.7 quantum - Cars & Trucks

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: how to find timing belts marks toyota rav4 2l

I have just replaced my water pump on my 1998 RAVE4, also, the timing belt and the other two belts. I had a tough time with the timing marks. The way you line these marks up is easy if you take the time, First, if you are changing the timing belt you pull the balancer and both top and bottom plastic covers,(do not try to pull top cover off before you take off balencer and the motor mount off or you will just break it.), Second after covers are removed you will have access to the timing belt, you can now remove it by loosening the tensioner bolt and pushing down on the tensioner wheel, the belt then can be taken off. Third take out number one sparkplug and replace the bottom cover by maybe two bolts so that you can see marks on cover, next replace the balancer and bolt. Turn the motor over by hand with the balancer so the small divit on the back of the balancer is on 0 or top dead center on the compression stroke, you can use a compression gauge for this or I just used a mirror and light to shine in the number one cylinder to see the piston. Next remove the balancer and cover and make sure to make a mark on crankshaft gear and housing. Next you will need mirror and flashlight, now turn camshaft gear clockwise to line the hole in the gear with the top timing mark. I recommend a small circle mirror for this. Now replace the belt. I turned the crank shaft gear one tooth counter clockwise off mark and the camshaft one tooth clock wise off mark so when the belt is on you can turn the camshaft gear counter clockwise to get tension on the belt and marks will line up. I would recommend changing water pump,tensioner wheel, and the idler wheel. After belt is on I would replace the bottom cover the balancer and the crankshaft sensor. Iwould then start it to make sure the water pump is not leaking and the motor is not pinging or you will have to tear it back apart again. Good luck and no I am not a certified mechanic just thought this would be helpful from my own experience.

Posted on Apr 30, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Aligning timing belt after breakage on 1996 toyota camry 2.2 liter 4 cylinder


Dustin, The attached links will explain timing alignment on 2.2 Camry engine. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Diagram of Timing Belt Marks and Installation
work on camry engine
Aligning timing belt after breakage on 1996 toyota camry 2 2 liter 4...
DIY GEN3 Timing Belt Waterpump Oil Seal Change Part 1 Toyota Nation Forum...

May 15, 2016 | Toyota Cars & Trucks

1 Answer

Set timing belt light on a quantum 2.5 diesel


Simply line-up the two timing marks, mount the belt, and try starting the vehicle. If the vehicle fails to start or backfires, remove the belt and rotate the cam sprocket ONE FULL TURN, then re-mount the belt. MAKE SURE THAT YOU ARE NOT ONE TOOTH OFF ONCE YOU MOUNT THE TIMING BELT (THE MARKS SHOULD STILL MEET EXACTLY).

May 14, 2015 | 2007 Toyota Quantum 2.5

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

1 Answer

Cam timing toyota quantum


double posted in 2 hrs.
back up one post.
and you forgot your car is in S. Africa and not most other places
location is 100% important. or no one knows what
quantum means.

Feb 20, 2014 | 2007 Toyota Quantum 2.7

1 Answer

How to set timing on toyota quantum 2,7


2007 , not in USA>

Toyota Quantum (South Africa)
wiki says.
2TR-FE 2,700 cc petrol engine

so google 2TR-FE, or read your FSM.
It features DOHC, 16 valves and VVT-i

changing chain are not easy.
lots of mistakes can blow an engine. if you let it snap.

our 2.7L in the Tacoma, is CHAIN drive.
im at alldata.com
58 steps and 25 photos. for just removal.
how'd you like that, here,
it take me 2 hours to get this , host it and link it.
why would any one do that.
why not pay $15 like we do.. and discounted here.
we dont have your car so pick 07 tocoma , it has same engine.
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

but your body is different so many steps will vary.
why no go to toyota and buy the FSM for your car and your country.
for best play

Feb 20, 2014 | 2007 Toyota Quantum 2.7

1 Answer

2TR TIMING MARKS


cam?
or spark,. my guess cam timing.
its in the FSM> and is not trival.
there are lots of steps. not just simple marks.
my guess, asking for hubby?

tell him to log in to alldata.com and read the page on topic.
there are lots of pitfalls. and for sure guessing.
hope i saved you a blown motor

Dec 19, 2013 | 2007 Toyota Quantum 2.7

1 Answer

TOYOTA QUANTUM 2.7VVTI TIMING


How to do timing on 2.7 toyota quantum

Sep 07, 2013 | 2007 Toyota Yaris

2 Answers

How to do timing on 2.7 toyota quantum


how to set the timing marks on the timing sprockets on a vvti quntum

Apr 30, 2012 | 2007 Toyota Quantum 2.7

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...