Question about Honda Accord
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Bumper cover removal
It is a little more complicated than that. There are two nuts below the headlight assemblies in the engine compartment. You will need to remove the battery and overflow bottle to get at the one on the passenger side. Remove the turn signals in the bumper, then there are 2 or 3 bolts holding a mounting bracket behind the each of the turn signals. There are a number of bolts with washer heads and reatiners on the underside of the bumper as the previous responder indicated.
Posted on Jan 26, 2009
reach underneath bumper, you will see the post with screws on each post. Just remove the nuts on both sides, and bumper will come off.
Posted on Jun 12, 2009
easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time
Posted on Jul 03, 2009
youll have to pull up very firmly or it may have to slide to the side its held in place by a bodyfastener. a screw that fits into a slot. but i would try pulling up first.
Posted on Dec 29, 2009
Installation of a front bumper can be
complicated. These helpful instructions may help a person with this
task. If you choose to install a bumper yourself, please be cautioned
that professional installation is always recommended. Please confirm
before you start that your safety equipment has been applied to you,
your car and your new bumper. These 10 easy steps can make a difficult
install relatively easy.
The following steps are detailed instructions that you can follow. It is very important that you make sure to read each step carefully and completely:
1. Look closely at the new bumper and your car for screws, bolts and clips. Remove these pieces from your existing front bumper and place them in a safe area. Follow this by the full removal of the cars current front bumper.
2. Next, test the fit of the new front bumper. Make sure that nothing hinders with the placement and fit on the car.
3. If the fitment is correct the installation process may move forward.
4. If the fitment is incorrect then the removal or repositioning of certain components, such as reinforcement bars may be required. This is because every car is different. If this is the case remove the element and test fit the front bumper again. This should be done with caution and is done at the installers own risk.
5. Most of the time the new aftermarket bumper is placed the exact way the factory piece was. The most important key to great fitment in installation is the drilling procedure. The holes should be drilled in the places that will give the piece a great fit. Usually, these holes will be drilled in the same place as the factory bumper. At this point only mocking is required.
6. When the bumper is in place, shaving or filing maybe required. Many parts will require this because certain areas are made with more material to lower the risk of damage. Also, if a car has been in an accident or previously modified, this may cause additional sanding, cutting or filing.
7. Now that the front fits well, be very precise and drill the holes.
8. Prepping for paint is what needs to be done after the holes have been drilled. Depending on what material the front bumper is made of will determine the steps for prepping.
9. After the piece has been painted, clear coating may be appropriate.
10. Make sure there are not any leftover parts and that everything is secure. After this is done, your front bumper installation process is complete.
Posted on Jun 02, 2010
Tips for a great answer:
Oct 18, 2012 | 1997 Honda Accord
Apr 27, 2011 | Honda Civic Cars & Trucks
Oct 07, 2009 | 2004 Honda Accord
Jul 14, 2009 | 2000 Dodge Grand Caravan
Jun 11, 2009 | 2005 Honda Accord
Jun 09, 2009 | 1998 Honda Accord
Feb 02, 2009 | 1993 Honda Accord
Jan 24, 2009 | 2002 Honda Odyssey
Dec 10, 2008 | 1998 Honda Accord
19 people viewed this question
Usually answered in minutes!