Question about Cars & Trucks

Open Question

How do you remove the reel from a mitchell punch 200 fishing reel

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I release the spring tension on this reel? How does one separate the top from the encased spring load area?


If this is fishing equipment, you have posted in wrong section. If this is automotive item, sorry, I am unfamiliar with it.

Aug 11, 2015 | Cars & Trucks

1 Answer

Where can I find a schematic of Shakespeare Fishing reels? They aren't necessarily at the Home address.


well any new reel I have gotten lately has the schematic printed on the box.but since I don't have any shakespear I can't say for sure Sorry

Jan 11, 2014 | 2004 GMC Sierra

1 Answer

Belt diagram


this can be found in many places.
1: on Radiator shroud
2: in FSM.
3: in operators guide under belts, if lucky, lost it?
4:alldata.com or mitchels

FSM
http://hondatech.info/downloads/Auto/Manuals/Civic/
OP GUIDE
http://justgivemethedamnmanual.com/honda/

today , i teach to fish.
and last
google is your friend.
google image, finds it.

Jan 02, 2014 | 1993 Honda Civic 4 Door

1 Answer

Sunroof slow operation


take a rag and spray it with brake part cleaner and clean down the sunroof tracks and then lube them with lube made for fishing reels from a sporting good store

Jul 04, 2012 | 2003 Chevrolet Impala

1 Answer

How do i re-spool the window regulator in my 99 Dodge caravan


You DON'T and you CAN'T. You need a new window regulator. It'n not as easy as putting new line onto a fishing reel. Sorry but I hope this helped.

Jul 14, 2011 | Dodge Caravan Cars & Trucks

1 Answer

Ignition switch is broke


Here are procedures for removing the ignitionlock assy. If equipped with SRS, extra care must be taken while removing ang installing to avoid damage to the SRS cable reel.

IGNITION SWITCH & LOCK CYLINDER
Removal
1. Remove steering wheel and combination switch (if necessary). Disconnect ignition switch harness connectors. If shear bolt studs are accessible, use a hacksaw to cut slots into exposed studs.

2. Remove studs using a screwdriver. If shear bolt studs are recessed or hard to reach with hacksaw, use a center punch on studs. Using a drill bit and screw extractor, remove studs. Place key in ACC position and remove ignition switch and lock cylinder.

Installation

To install, reverse removal procedure. Install NEW shear bolts. Tighten shear bolts finger tight. Ensure proper operation of ignition switch and lock cylinder. Tighten shear bolts until heads break off. Install combination switch, upper and lower steering column covers and steering wheel (if removed). Tighten steering wheel nut and Torx screws to specification.

Sep 26, 2010 | 1996 Toyota Avalon

1 Answer

Replace airbag on `92 honda accord


When an SRS cable reel assembly is removed and set aside during vehicle repairs, the cable reel may rotate inside the assembly so it is no longer centered. If the assembly is reinstalled with the reel off-center, the cable can break when the steering wheel is turned to full lock. The cable reel holding fixture locks the reel while the assembly is off the vehicle, keeping it centered for reinstallation.
CABLE REEL REMOVAL PROCEDURE
1. Follow the procedure in the appropriate service manual for disconnecting the battery, and removing the dashboard panels, steering column covers, airbag, and steering wheel.
^ Always install short connectors on the connectors for the driver's and passenger's (if so equipped) airbags.
^ Make sure the front wheels are pointed straight ahead before removing the steering wheel.
2. Verify that the cable reel is centered; the yellow gear tooth is lined up with the alignment mark on the cover. Install the cable reel holding fixture in the cable reel assembly as shown. Use a TORX T-10 wrench.
3. Disconnect the 6-P connector, then remove the cable reel assembly.
CABLE REEL INSTALLATION PROCEDURE
1. Verify that the front wheels are still pointed straight ahead.
2. Reinstall the cable reel assembly, and reconnect the 6-P connector.
3. Remove the cable reel holding fixture.
4. Follow the service manual procedure for reinstallation of the steering wheel, airbag, steering column covers, and dashboard covers.
5. Verify SRS operation as described in the service manual. Road test the vehicle.
^ If the steering wheel spoke angle is not correct, change it by adjusting the tie rod ends. Do not remove and reposition the steering wheel.
PARTS INFORMATION
Cable reel holding fixture:
For 1992-95 Civic and Ohio-produced 1992-95 Accord
P/N 77900-SPO-999, H/C 4733564
For 1991 Accord Wagon, 1992-95
Prelude, 1995 Odyssey and Japan-produced
1992-95 Accord
P/N 77900-SM5-999, H/C 4733572
WARRANTY CLAIM INFORMATION
Use the Flat Rate Manual information for the repair being performed.

Jan 28, 2009 | 1992 Honda Accord

5 Answers

Cv joint


is it on the driver side or the passenger side? when i have a little trouble i use a slide hammer. put the nut on the shaft and use the 3 jaw attachment of a slide hammer this will help you.

Sep 01, 2008 | 1997 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...