Question about 2001 Mazda Tribute

Open Question

Hesitation when driving my 1988 Mazda B2200 pickup

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jingB
  • 19 Answers

SOURCE: mazda engine bad

yes, i believe you could put any engine on your pick-up provided it is the rear wheel type set-up and the engine comes with its own tranny. problem is, if changing the engine mounts, tranny mounts, wiring set-up and exhaust system layout would not be of any problem to you. might as well look for the same mazda engine you have as a replacement to ease installation.

Posted on Apr 14, 2009

soc21610k
  • 215 Answers

SOURCE: price on a 1991 B2200 Mazda Pickup truck carburetor

Depends if you want new or used, Location, and a few other variables

Posted on Jun 04, 2009

  • 6 Answers

SOURCE: can a bad ignition switch cause the truck to die

Yes, bad ignition switch can cause that, did on my B2200.

Posted on Dec 14, 2009

  • 384 Answers

SOURCE: speedometer and odometer stopped working

need a new speedo cable from tranny to back of dash

Posted on Feb 25, 2010

ZJLimited
  • 17970 Answers

SOURCE: i need a duagram on replacing a thermostat 1994

Mazda Trucks 1987-1993 Repair Guide
Thermostat

printpage_icon.gif

REMOVAL AND INSTALLATION

If the replacement thermostat is equipped with a &inch;jiggle pin&inch;, the pin must be install facing upwards toward the top of the engine (12 o'clock), and should be on the side facing the water outlet. When installing the thermostat gasket, the seal print side should face the cylinder head.
2.2L Engine
See Figure 1
  1. Drain enough coolant to bring the coolant level down below the thermostat housing. the thermostat housing is located on the left front side of the cylinder block.


CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethelyne glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Disconnect the temperature sending unit wire.
  2. Remove the coolant outlet elbow.
  3. If so equipped, position the vacuum control valve out of the way. The vacuum control valve is not used on California trucks.
  4. Disconnect the coolant by-pass hose from the thermostat housing.
  5. Remove the thermostat and housing from the engine.
  6. Note the position of the jiggle pin and remove the thermostat from the housing.
  7. Remove all gasket material from the parts.
e0283c4.jpg

Fig. 1: Thermostat installation

To install:

  1. Position the thermostat in the housing with the jiggle pin up. Coat a new gasket with sealer and install it on the thermostat housing.
  2. Install the thermostat housing using a new gasket with water resistant sealer. Tighten the bolts to 14-19 ft. lbs. (19-25 Nm).
  3. Install the coolant outlet elbow and vacuum control valve (if equipped).
  4. Connect the by-pass and radiator hoses.
  5. Connect the temperature sending unit wire.
  6. Fill the cooling system with the proper coolant. Operate the engine and check the coolant lever. Check for leaks.

Hope helps with this (remember rated this).

Posted on May 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 1989 mazda b2200 pickup it just started blowing fuses every time i turn on my park lights.


check tail & park light circuits for short to ground. best place to start is at trailer wiring harness. (if equiped) i might want to purchase a "short finder" tool. (fairly cheap at harbor freight.) to help locate area of short. good luck.

Oct 21, 2011 | 1988 Mazda B2200

1 Answer

What side is the high pressure side on the power steering gearbox of a 89 mazda b2200 pickup


It should be the larger of the 2 power steering hoses. It should have metal crimped fittings attached to it.

4c162a4.jpg

Oct 23, 2010 | 1988 Mazda B2200

1 Answer

How do i lower the spare tire on 1989 Mazda b2200 pickup?


will need the original wheel tools is about 4 foot long with hook on one end and square solid tool joint on the other which takes the handle supplied. go to the rear of the vehicle and insert the tool into the slot on top of the spare wheel and wind anti clockwise until the wheel is onthe ground

Jul 27, 2010 | 1988 Mazda B2200

1 Answer

How to quiet noisey lifters


replace lifters or run diesel fuel thru engine at next oil change to remove sludge and coating on lifters

Mar 03, 2010 | 1988 Mazda B2200

1 Answer

I own a 1993 mazda b2200 pickup and put 2inch drop spindals on it and the outer steering components hit the factory tires and rims how can i remidey this


i understand the problem chad skeet69 is having w/his 1988 mazda b2200. why would you lower a b2200? doesn't that kind of defeat the purpose of hauling water with it? one way to fix your problem is to move. get expert help from a certified mechanic. it was fun talking to you in emails but i'm not interested in those kind of activities.

Jan 20, 2010 | 1988 Mazda B2200

1 Answer

Price on a 1991 B2200 Mazda Pickup truck carburetor


Depends if you want new or used, Location, and a few other variables

Jun 04, 2009 | 1988 Mazda B2200

1 Answer

How do you change the starter out of a 88 mazda pickup B2200???


first things first make sure you unhook you battery then mark all the wires to your starter as you are removing them. remove the starte.then put its all back the way it was.

Apr 29, 2009 | 1988 Mazda B2200

1 Answer

Mazda engine bad


yes, i believe you could put any engine on your pick-up provided it is the rear wheel type set-up and the engine comes with its own tranny. problem is, if changing the engine mounts, tranny mounts, wiring set-up and exhaust system layout would not be of any problem to you. might as well look for the same mazda engine you have as a replacement to ease installation.

Apr 14, 2009 | 1988 Mazda B2200

1 Answer

B2200 Chassis prt number


They are two totally different frames. The 2200 is a Mazda sourced vehicle while the 2500 is Ford sourced, based on the Ranger pickup.

Mar 11, 2009 | 1988 Mazda B2200

1 Answer

ROUGH IDLE AND HIGH FUEL CONSUMPTION - HESITATION


Try checking your Spark plugs (they MUST be the right type, clean, and properly adjusted: and try adjusting your timing. Either or both of these could cause this type of problem Hope it helps. If so, don't forget to rate the answer, will you?

Dec 13, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
2001 Mazda Tribute Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...