Question about 1998 Lexus Gs 300

Open Question

Have an 1998 Lexus GS300, i replaced the tps, how to reset?

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 98 lexus gs300 codes p1120 p1121

I wanted to start a thread specifically about failures within the throttle body concerning the GS300 (1998 in my case)

My symptons were:
VSC, VSC OFF, and ENGINE Lights would come on, followed by my car going into Limp Mode, where only that last 25% (if that) of the throttle would respond (basically have to floor the pedal to even move at all).

During the mornings, or when the engine was COLD, the throttle operated normal...then once the car warmed up, usually at about 10 mins, the problem would start...it happened intermitantly at first...1 or 2 days over the course of a week, then it became more consitent, until last week it became a daily problem.

The first part I tried was the Throttle Position sensor, which is on the front side of the throttle body, and the easiest thing to replace...this didnt help at all. $300 part from Lexus, $80 part from RockAuto.com (exacly same part toyota OEM)

THE PART THAT FIXED THE PROBLEM:
===========================================
"Idle Valve Motor", which is the larger electrical object next to the TPS on my 98 GS300. Problem is solved.

The Codes I got were P1120 and P1121 - Accelerator Sensor problem. However it wasnt really the Accelerator Sensor, it was indeed to actual electrical Motor that controls the opening of the Butterfly valve inside the Throttle body.

I found the problem by good old trouble shooting, and using an ohm meter to see if the throttle electric motor was getting elev, I found that the elec motor just to the left of the TPS was basically freaking out and shutting down. The Accelerator Pedal Sensor is on the Back-side of the throttle body where the throttle cable connects to, and has a spring on it. It was fine.

GS300's are indeed "drive by wire" concerning the throttle...the cable triggers the Accel Pedal Sensor, which sends a signal to the ECU, the ECU then sends power to the Idel Valve Elec Motor (next to the TPS), which opens and closes the mechanical butterfly valve, then the TPS sensor detects how far the elec motor is actually opening the butterfly valve...its a closed-loop feed-back system, meaning any failure in any sensor will cause the entire systm to fail.

The throttle cable apparently is ONLY there to allow the fail-safe of having that last 10-25% throttle when the electronic system fails...there is a gearbox inside the throtle body which allows the tail end of the throttle to manually engage the butterfly valve...the rest of the time, the butterfly valve is 100% opened and closed via the idle control motor.

Posted on Jul 08, 2009

ZJLimited
  • 17970 Answers

SOURCE: HOW TO REPLACE 100A FUSE ON 1994 LEXUS GS300

The 100 Amp alternator fuse is blown under the hood in the fuse block, it has a clear plastic cover on it for inspection, the designation is marked inside the fuse panel. This fuse is bolted in inside the fuse box, the fuse box has to be removed and opened to get to the bolts that connect the fuse in.

Here you have the Lexus-GS-300-Wiring-Diagram-Manual

Good luck (remember rated this help).

Posted on Dec 01, 2009

  • 7 Answers

SOURCE: how to replace fuel filter on 1994 lexus gs300

you first find the fuel pump fuse then allow to run the engine then remove the fuel pump pressure fuse, immediately engine will stop, this is to reduce the fuel pressure in fuel lines, jack up the vehicle fuel filter is located under the car just infront of rear side driver tire remove the old one and fix the new.

Posted on Dec 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 gs300 high idle when warm


check the TPS sensor and circuit

May 25, 2017 | 1994 Lexus GS 300

1 Answer

1998 lexus gs300 code p0155


P0155 O2 Sensor Heater Circuit Malfunction (B2S1)
bank 2 ...side one

either the 02 sensor has failed or getting too much voltage

go with replace 02 sensor first

Mar 08, 2017 | Lexus Cars & Trucks

1 Answer

1998 Lexus gs300 Changed battery with door locked


Hi follow this link , i know it refers to a different model lexus but i'm pretty sure the procedure would be the same, otherwise ring a Lexus dealer and ask them for the procedure but knowing these top marque vehicles they do like to charge for doing very little , hopefully this link will help
How to Reset the Anti Theft Lock on Lexus LS400 Sedan eHow

Sep 30, 2014 | 1998 Lexus Gs 300

2 Answers

98 GS300 HEAT


as in no buttons or what.. all electronic controls?? some have 2 buttons.. temp up and temp down..if it shows a number..raise it..

Dec 09, 2013 | 1998 Lexus Gs 300

1 Answer

Where can I purchase a shift solenoid for a Lexus GS300 1998, with the a650 tranny?


You can buy the solenoid in the below link

http://www.lexuspartsnow.com/components/1998-lexus-gs300~shift-lever-retainer-33-12-4413.html

Or if you want to know any nearby store please tel us where you live at to give the nearest location.

Jan 18, 2011 | 1998 Lexus Gs 300

1 Answer

Changed battery in 94 lexus GS300, now the check


try to take cables off battery let sit for five or tem min. then put + on first

Jan 01, 2010 | 1994 Lexus Es 300

3 Answers

98 lexus gs300 codes p1120 p1121


I wanted to start a thread specifically about failures within the throttle body concerning the GS300 (1998 in my case)

My symptons were:
VSC, VSC OFF, and ENGINE Lights would come on, followed by my car going into Limp Mode, where only that last 25% (if that) of the throttle would respond (basically have to floor the pedal to even move at all).

During the mornings, or when the engine was COLD, the throttle operated normal...then once the car warmed up, usually at about 10 mins, the problem would start...it happened intermitantly at first...1 or 2 days over the course of a week, then it became more consitent, until last week it became a daily problem.

The first part I tried was the Throttle Position sensor, which is on the front side of the throttle body, and the easiest thing to replace...this didnt help at all. $300 part from Lexus, $80 part from RockAuto.com (exacly same part toyota OEM)

THE PART THAT FIXED THE PROBLEM:
===========================================
"Idle Valve Motor", which is the larger electrical object next to the TPS on my 98 GS300. Problem is solved.

The Codes I got were P1120 and P1121 - Accelerator Sensor problem. However it wasnt really the Accelerator Sensor, it was indeed to actual electrical Motor that controls the opening of the Butterfly valve inside the Throttle body.

I found the problem by good old trouble shooting, and using an ohm meter to see if the throttle electric motor was getting elev, I found that the elec motor just to the left of the TPS was basically freaking out and shutting down. The Accelerator Pedal Sensor is on the Back-side of the throttle body where the throttle cable connects to, and has a spring on it. It was fine.

GS300's are indeed "drive by wire" concerning the throttle...the cable triggers the Accel Pedal Sensor, which sends a signal to the ECU, the ECU then sends power to the Idel Valve Elec Motor (next to the TPS), which opens and closes the mechanical butterfly valve, then the TPS sensor detects how far the elec motor is actually opening the butterfly valve...its a closed-loop feed-back system, meaning any failure in any sensor will cause the entire systm to fail.

The throttle cable apparently is ONLY there to allow the fail-safe of having that last 10-25% throttle when the electronic system fails...there is a gearbox inside the throtle body which allows the tail end of the throttle to manually engage the butterfly valve...the rest of the time, the butterfly valve is 100% opened and closed via the idle control motor.

Nov 23, 2008 | 1998 Lexus Gs 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...