Question about Cars & Trucks

Open Question

Kia pregio van cannot bleed master cylinder and clutch doing as you would a brake one

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 51 Answers

SOURCE: clutch cylinder inside car is it broke

you have to bleed the air out of it. If there is not fluid leaking from the master cylinder on the firewall.it can leak on the inside of car or the out side if the master cylinder is bad.first make sure the reservoir stays full then open the bleeder on slave cylinder. this is called gravity bleeding. once fluid comes out, tighten bleeder, pump pedal one time loosen bleeder while holding clutch pedal down and then tighten. do this repeatedly until no air comes out. you can pump pedal several times,then hold and bleed however you like but I have better luck with individual pumps. just make sure that the lines hooked to slave cylinder are tight and there are no air leaks. and that the line does not go below the slave cylinder because sometimes air gets trapped in the lowest part of system.

Posted on Jan 12, 2009

Ad
  • 232 Answers

SOURCE: Spongy brakes after bleeding them 2 times. Should I try to bleed the master cylinder or replace it?

Honestly your guess is as good as mine. But I don't think the master cylinder is NOT bad you still have air in the system. Get a big bottle of brake fluid bleed all four sides until you run out of fluid or your brakes work properly. You should divide the bottle's content in four, then use each quantity in each side. You'll be removing air and contaminated fluid from the system. Get a small hose that fits on the bleeders and an appropriate container. I have a good feeling if you do this your brakes will work just fine. I don't know how you are bleeding the brakes. I'll let you know the proper way just in case. This is a two man job, with the wheel off, have someone start the car. Have them pump the brakes a few times to get pressure. 1With the brake pedal UP open the bleeder, 2then have your assistant press the brake pedal all the way down and leave it completely pressed down. 3Close the bleeder valve, once close and only with the valve closed have'm release the brake. Repeat as necessary, bake depressed, open valve first then press brake. DO NOT depress until valve completly closed. Close valve THEN depress. Good Luck!

Posted on May 15, 2009

  • 1 Answer

SOURCE: 2003 town and country brake problem

Did your mechanic use a DRB III or equivalent scanner before performing the bleeding procedure after installing the master cylinder? This is a requirement by the manufacturer (Chrysler) when bleeding the brake system.

Posted on May 15, 2009

  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: 1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My clutch pedal has no pressure and will not go into any gear what's the problem I have a kia spectra 2004


with a cable clutch operation replace the clutch cable as it has broken
if hydraulic operation replace the clutch slave cylinder and bleed the system
if nothing has been done to the clutch for the life of the vehicle , replace both the clutch master cylinder and the clutch slave cylinder as both will have reached end of service life
IF you are not capable of the procedure take it to an accredited clutch and brake specilaist shop

Jan 07, 2016 | Kia Cars & Trucks

1 Answer

Do you need to power bleed a clutch for a 2004 pregio kia van


please post to KIA , not honda.
but is the same.
attach power bleeded to MC
set 1-2PSI
open bleeder valve at slave, let it run till no bubble and close.
dont let MC run dry
no different than brakes.

Aug 01, 2013 | 1996 Honda Accord

1 Answer

Cannot change gears while engine is on


if vehicle has clutch, it may be due to no brake fluid in clutch master cylinder, or bad clutch. if no fluid in master, bleeding will need to be completed.

Dec 25, 2012 | 2005 Kia Sorento

1 Answer

Kia Sephia 5 spd won't shift gears


You need to bleed the lines with a special tool, contact the dealer on this.

Jun 13, 2012 | 2000 Kia Sephia

1 Answer

I cannot bleed the clutch on my kia caranvil


First lets make sure we are on the same page here.Your saying you have no clutch resivioir and the system is feed from the brake master cylinder correct .Now the clutch has two clylinders the master witch atteches to the clutch pedal with the rod and it mounted on the fire wall . The slave cylinder is mounted between the bell houseing and the engine . And to replace this you would need to remove the transmission and actualy moves the pressure plate springs back when the pedal is depressed . Think of it like a light its eighter on or off and pushing the pedal down turns it off Normaly the clutch would be bleed at the slave cylinder there should be a bleeder fitting near the top of the bell hoseing. And should be bleed just a brake line no trick you just have to find the bleeder . Check for fluid at the clutch master on the pedal if you see any oil at all leaking you will never be able to keep it bleed sometimes there bad even when new .If oil can get out air is GETTING IN and it will constantly need to be rebleed. Any questions fell free to ask

Mar 19, 2012 | Cars & Trucks

1 Answer

Ford van brakes go "soft"


The master cylinder probably needs new seals and the brakes need bleeding. First try replacing the brake fluid and doing a good bleed. If that does not solve the problem, go for the master cylinder.

Mar 20, 2011 | 1993 Ford Econoline

1 Answer

I have a Pregio van that I just tried bleeding the clutch system and after a while all that was coming out was air and the pedal went soft. I think the master and slave cylinder may need replacing as when...


Hi and welcome to FixYa!

It will cost you at least $50 on both the primary and secondary. Yes they surely need replacement to resolve the problem.

Hope this helps and thank you for using FixYa! Have a good one!

Mar 06, 2011 | Kia Sephia Cars & Trucks

2 Answers

My 1996 Chevrolet K3500 Dually has a hydraulic clutch, how do I change the fluid and bleed it.


FIRST REMOVE ALL OLD FLUID FROM CLUTCH MASTER CYLINDER YOU CAN USE A SIPHON YOU HAND PUMP.AUTO PARTS STORES SELLS THE HAND PUMP SIPHONS. THEY DONT COST MUCH AND KEEP FROM MAKING A MESS.SIPHON OUT MUCH AS YOU CAN THE OLD FLUID IN THE CLUTCH MASTER CYLINDER.THEN POUR IN THE NEW FLUID DOT 3 BRAKE FLUID IN CLUTCH MASTER CYLINDER.OKAY YOU NEED A HELPER.LOCATE THE SLAVE CYLINDER.REMOVE SLAVE CYLINDER HOLD SLAVE CYLINDER 45 DEGREES WITH BLEEDER SCREW LOCATED AT THE HIGHEST POINT.HAVE A SMALL DRAIN PAN UNDER SLAVE CYLINDER.HAVE HELPER FULLY DEPRESS AND HOLD THE CLUTCH PEDAL THEN OPEN BLEED SCREW.CLOSE THE BLEED SCREW AND HAVE HELPER RELEASE THE CLUTCH PEDAL.REPEAT THIS PROCESS UNTIL ALL THE OLD BRAKE FLUID AND AIR BUBBLES LEAVES THE HYDRALIC SYSTEM AND WHEN YOU CAN SEE GOOD STREAM CLEAN FLUID NO BUBBLES YOU HAVE GOOD SOLID CLUTCH ALL IS GOOD.MAKE SURE THROUGH THE BLEEDING PROCESS YOU DONT LET CLUTCH MASTER CYLINDER RUN DRY OR YOU WILL HAVE TO START OVER.KEEP CLUTCH MASTER CYLINER FULL BRAKE FLUID WHILE DOING THE WHOLE BLEEDING AND FLUSHING PROCESS.

Jan 22, 2011 | 1996 Chevrolet C/K 3500

1 Answer

Clutch pedal drops to the floor with no real effort. How do I check the master cylinder?


CLUTCH AND MASTER CYLINDER SHARE THE SAME RESERVOIR YOU CHECK LEVEL IN THE MASTER CYLINDER.ADD BRAKE FLUID TO THE MAX LINE DONT OVER FILL.IF MASTER CYLINDER RESERVOIR IS EMPTY.CHECK FOR FLUID LEAKS AT CLUTCH LINES AND CONNECTIONS AT CLUTCH RELEASE CYLINDER AND CHECK BRAKE LINES - CALIPERS - WHEEL CYLINDERS AND BRAKE BOOSTER.FIX LEAKS AND BLEED BRAKE AND CLUTCH SYSTEM.

Jul 25, 2010 | Cars & Trucks

1 Answer

Are the brake master cylinder and the clutch slave cylinder interconnect in some way? I'm told that the slave cylinder get its fluid from the master cylinder.


The brake system and the clutch master cylinder have the same fluid tank, look at the brake master cylinder fluid tank, on the right hand side about half way up is a hose that goes over to the clutch master cylinder, if fluid level is not above this hose the clutch will stop functioning. If the clutch slave cylinder, mounted on the front side of transmission bellhousing, leaks then the clutch will stop functioning. The slave cylinder has a bleed screw, check these items and fill and bleed as neccessary. Hope this helps, let me know.

Jul 28, 2010 | 1995 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...