Question about Suzuki Cars & Trucks

1 Answer

Coolant sensor location

Where is ECT on the 2001 Esteem 4-1.8

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

Did you find it yet, if not, i can, ask.
i can click, alldata dot com and see it.
the 1.8L is used on Esteem and Sidekicks
ECT (rules)
it has 2 pins or more, never 1.

on my 1.8l
see RADiator, see 2 large hoses to it.
one is input other is out put.
one goes to the thermostat housing, no its not there. like most cars. not on PUMP (coolant)
the other hose (huge) goes to a fitting on the engine block.
page 21 and part ID 21.
here ,called the coolant return fitting. IT IS THERE on mine.
http://www.fixkick.com/engine/20Liter/20L-PARTSFINDER1.pdf

Posted on Sep 15, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 345 Answers

SOURCE: 2001 focus/ect sensor

its screwed into the cylinder head ,when you fit a new 1 dont overtighten it they sense temp of the head they dont screw into the water jacket!!!!!!!!!!!!!!!!!!!!

Posted on Oct 10, 2008

  • 141 Answers

SOURCE: location of ECT sensor

when you open the hood take your right hand and follow the upper rad hose down to the eng. when it stops thats the themostat housing the ect sensor is screwed into that housing there are two sensor one will have one wire and the other will have two you want the two wire one. be carful remove the conector the like to break good luck kdc744

Posted on Jan 08, 2009

jeffbvegas1
  • 520 Answers

SOURCE: where is the coolant temperature sensor

These are located in the cylinder head in the back of the head...meaning 180 degrees from the belts and pulleys(front) or the side the transmission is on. Two sensors exist...the single wire sensor is for the dash gauge. Saturn pn# 21025106 is the one you need

Posted on Aug 12, 2009

  • 4 Answers

SOURCE: Location: Coolant Temp Sensor 2001 Lincoln LS V6

It is on the Driver side of engine in between the COP's (Coil on plugs) simply unplug the wire use a 19 or 3/4 deep well socket and unscrew it and put it new one... The whole process should only take 10-15 minutes.

Posted on Aug 09, 2010

  • 1608 Answers

SOURCE: where is the ect(coolant) sensor

The engine coolant temp sensor is located just below the throttle body.Just remove the air cleaner tube and you should be able to see it.There will be a black and a yellow wire on the connector.Hope this helps.Good luck.

Posted on Nov 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the coolant temp.sensor located on 2001 dodge 1500


The alternator needs to be removed to easily access and locate coolant temperature sensor.For more details and ECT diagram on 2001 dodge ram click the link below and follow the details to replace the coolant sensor:-----

http://technoanswers.blogspot.com/2012/10/dodge-coolant-temperature-sensor.html
--------
These details will help.
Thanks.

Oct 21, 2012 | 1997 Dodge Ram 1500 Club Cab

3 Answers

P0118


As with all engine codes there is no one solution fits all, here is the info on the code from the diagnostic material.
P0118 - Engine Coolant Temperature Circuit High Input
Possible causes - Low engine coolant level
- Engine Coolant Temperature (ECT) sensor harness is open or shorted
- Engine Coolant Temperature (ECT) sensor electrical circuit poor connection
- Faulty Engine Coolant Temperature (ECT) sensor
- Faulty engine coolant thermostat P0118 Description The Engine Coolant Temperature (ECT) sensor is used to detect the engine coolant temperature. The sensor modifies a voltage signal from the Engine Control Module (ECM). The modified signal returns to the ECM as the engine coolant temperature input. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases.

Feb 02, 2012 | 2005 Chevrolet Tahoe

1 Answer

Location of engine coolant temperature sensor


Automobiles: 2000 Ford Escort ZX2 4-cylinder 2.0L MFI DOHC

NOTE
The "left" side of the engine is the driver's side.

The Engine Coolant Temperature (ECT) sensor is a thermistor (a device which changes resistance or voltage as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM (Powertrain Control Module - aka "the car's computer").

The ECT sensor is mounted in the following locations (small Ford engines):

1.8L engines: in the cylinder head
1.9L engines: threaded into the heater hose inlet pipe
2.0L engines: at the left rear of the engine

2.0L Zetec Engine

(1) Partially drain the engine cooling system using a clean container. If coolant is in good condition, retain for reuse.
(2) Disconnect the battery ground cable.
(3) Disconnect the electrical wiring connector from the engine coolant temperature (ECT) sensor.
(4) Remove the retaining clip and the ECT sensor.


12_5_2011_5_38_05_pm.jpg

Fig. 1 Escort ZX2 ECT sensor - The retaining clip is removed (at the solid arrow). Withdraw ECT sensor by gently wiggling/pulling in the direction of the dashed arrow.

To install:

NOTE
Coat the ECT sensor O-ring with clean coolant prior to installation.

(1) Replace the retaining clip and the ECT sensor.
(2) Connect the electrical wiring connector from the Engine Coolant Temperature (ECT) sensor.
(3) Connect the battery ground cable.
(4) Refill the engine cooling system. An inexpensive plastic "Radiator Funnel" will help with this task.

Dec 05, 2011 | 2000 Ford Escort

1 Answer

Where is the temp gage sensor location 2001 merk cougar


Hi there,

The temperature gauge relies on readings from the Engine Coolant Temp (ECT) Sensor.

The ECT sensor is usually located on (or near) the thermostat/coolant housing.

Refer to component No. 8 (2.0L Engine):

wolfman304_70.gif


Refer to component No. 9 (2.5L Engine) locate under bypass tube:

wolfman304_71.gif

Hope this helps.


Cheers,

Aug 27, 2011 | 2001 Mercury Cougar

1 Answer

Coolant sensor replacement


The exact locations and picture of Engine Coolant Temp (ECT) sensors on 2001 VW Jetta TDI:

1. ECT sensor 1 placed on cylinder head:

tdisline_485.jpg




2. ECT sensor 2 placed on the left bottom side of the radiator:

tdisline_486.jpg

Apr 28, 2011 | 2001 Volkswagen Jetta TDI

1 Answer

How do you replace coolant temperature sensor on an 2001 Oldsmobile Intrigue


Removal & Installation To Remove:
ECT sensor 3.5L engine 93174g14.gif

  1. Disconnect the battery ground cable.
  2. Drain the coolant below the level of the engine coolant temperature (ECT) sensor.
  3. Disconnect the ECT sensor electrical connector.
  4. Carefully remove the ECT sensor.
To Install:
WARNING
Damage to the coolant sensor will affect the operation of the fuel control system.
  1. Coat the ECT sensor threads with thread sealer.
  2. Install the ECT sensor. Tighten the sensor to 15 ft lb (20 Nm) on 3.5L engines and 22 ft lb (30 Nm) on 3.8L engines.
  3. Install the ECT sensor electrical connector.
  4. Connect the battery ground cable.
  5. Refill the cooling system using the recommended procedure.
prev.gif next.gif

Aug 29, 2010 | 2001 Oldsmobile Intrigue

1 Answer

Temperature gauge location


Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • The coolant to just below the level of the engine coolant temperature (ECT) sensor
    • The air intake duct (1997-1998) gm_mv_ven_ect.gif

    • The ECT sensor electrical connector
    • The ECT sensor
To Install:
  1. Install or connect the following:
    • P/N 9985253 sealer or equivalent to the threads
    • The sensor
      1. Torque to: 15 ft. lbs. (20 Nm) (2001-2005)
      2. Torque to: 17 ft. lbs. (23 Nm) (1997-2000)
    • The ECT sensor electrical connector
    • The coolant
prev.gif next.gif

Aug 17, 2010 | 2000 Oldsmobile Silhouette

1 Answer

I need a diagram of the exhaust system on a Mazda 626


0996b43f80203328.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2000 MPV

1 PCM 2 Mass air flow (MAF)/intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Fuel tank pressure sensor 5 Engine coolant temperature (ECT) sensor 6 Crankshaft position (CKP) sensor 7 Camshaft position (CMP) sensor 8 Knock sensor 9 Heated oxygen sensor (HO2S) (front, LH) 10 Heated oxygen sensor (HO2S) (front, RH) 11 Heated oxygen sensor (HO2S) (rear, LH) 12 Heated oxygen sensor (HO2S) (rear, RH) 13 EGR boost sensor 14 Power steering pressure (PSP) switch 15 Main relay


0996b43f8020330c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2001 MPV

1 PCM 2 Mass air flow (MAF)/Intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Engine coolant temperature (ECT) sensor 5 Crankshaft position (CKP) sensor 6 Camshaft position (CMP) sensor 7 Knock sensor 8 Heated oxygen sensor (HO2S) (front, LH) 9 Heated oxygen sensor (HO2S) (front, RH) 10 Heated oxygen sensor (HO2S) (rear, LH)* 11 Heated oxygen sensor (HO2S) (rear, RH)* 12 EGR boost sensor


0996b43f8020330f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart- 2002-06 MPV

May 22, 2010 | 2004 Mazda MPV

2 Answers

Engine code p0115


replace the sensor and or check the wiring socket going to the sensor

Jun 02, 2009 | 2001 Hyundai Elantra

1 Answer

2001 4.6L f150 temperature control sensor location


temp control for cooloing system or heater sysem?

ECT - Engine Coolant Temperature Sensor

The engine coolant temperature (ECT) sensor (Figure 27) is a thermistor device in which resistance changes with temperature. The electrical resistance of a thermistor decreases as the temperature increases, and increases as the temperature decreases. The varying resistance affects the voltage drop across the sensor terminals and provides electrical signals to the PCM corresponding to temperature.
Thermistor-type sensors are considered passive sensors. A passive sensor is connected to a voltage divider network so that varying the resistance of the passive sensor causes a variation in total current flow.
Voltage that is dropped across a fixed resistor in a series with the sensor resistor determines the voltage signal at the PCM. This voltage signal is equal to the reference voltage minus the voltage drop across the fixed resistor.
The ECT measures the temperature of the engine coolant. The sensor is threaded into an engine coolant passage. The ECT sensor is similar in construction to the IAT sensor.
-----------------------------------------------------------------------------------
115d42e.gif

Jan 19, 2009 | 2001 Ford F150 Styleside SuperCrew

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...