Question about 2005 Volkswagen Polo 1.4i

Open Question

Setting timing marks - 2005 Volkswagen Polo 1.4i

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Setting timing marks to get vehicle to start after engine overhaul


Timing marks setting Corolla 4A-FE.
Align the notch on the crankshaft pulley with the "0" mark on the timing belt lower cover.
25679262-y0srr1ownybx5goll4rgvnpm-5-0.jpg

With the crankshaft pulley being aligned with the 0 mark on the timing belt cover, the hole on the camshaft sprocket should exactly be in front of the notch of camshaft bracket.


25679262-y0srr1ownybx5goll4rgvnpm-5-2.jpg
Hope that works.

May 04, 2015 | 1998 Toyota Corolla

1 Answer

What is timing belt installation sequence on a 1999 Mazda 626 6 cylinder?


set mark on crankshaft to TDC mark on timing cover. set mark on cam pulley to align with mark on head .if more than one mark on pulley rotate by hand till exhaust and inlet just rocking then align closest marks .

May 11, 2014 | Cars & Trucks

1 Answer

Ichanged the head on my 91 geo storm 1.6 dohc and now it won't start


Double check crankshaft timing mark, on your lower timing cover has some timing marks - crankshaft should be on the 0 mark. Camshaft timing marks--intake camshaft mark set at 3 o'clock and exhaust camshaft mark set a 9 o'clock. These timing marks are critical for motor to run and start correctly. These timings marks can move while trying to install the timing belt. After, you confirm or reset timing and belt, you can confirm timing is correct by rotating the crankshaft twice. Your timing marks should be on right on timing marks discussed at the top of the page. If timing marks are off, start over with timing process.

Jul 11, 2012 | 1990 Geo Storm

1 Answer

1983 lincoln mark vi how to set the time


see internet.

1983 LINCOLN MARK VI Timing Set - RockAuto

www.rockauto.com/catalog/x,carcode,1188323,parttype,5756
1983 LINCOLN MARK VI 5.0L 302 cubic inch V8 : Engine : Timing Set, Price, Add ...Timing Set - 3 Pc.

Feb 22, 2012 | 1983 Lincoln Mark VI

1 Answer

I need to set up the camshaft timing marks on a 1994 mazda b2600


its not just the camshaft timing marks you set up, you also have to have the crankshaft timing mark set right to or you may damage your engine
check the internet for the right timing procedure for you model car ok

Jun 11, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

How do u set the ignition timing i have 2 marks then have 3 marks after it


Hello! Timing is set using the RED mark...It is the middle mark in the equally spaced group of three marks...Set with engine at normal operating temperature...All vacuum lines connected...670 RPM...

Guru............Saailer

May 04, 2010 | 1994 Honda Civic

1 Answer

I have a 2000 dodge caravan trying to time it dont know how has a 3.0 motor


set the timing mark on the crankshaft to the mark on the oil pump, then set the timing mark on the camshaft to the mark on the alternator bracket/set second camshaft mark to mark on the inner timing belt cover. line up all mark as decribed. be sure before u set anything to bring #1 piston all the way up to top. with belt on turn crankshaft 2 full turns to bring #1 piston back to top if the cams are not lined up correctly loosen belt and start over again until everything lines up correctly. you may have to do this a few times but it will work.

Mar 31, 2010 | 2002 Dodge Caravan

1 Answer

Timing marks setting Hyundai Lantra


Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Mar 21, 2010 | Hyundai Motor 1996 Elantra

1 Answer

Cant get timing belt on


The mechanic should check on the timing mark . sir you have to look at the timing mark to set the timing chain .there is a timing mark in the pulley where you will place the timing chain.and then there also is a timing mark in the place where you place the pulley set it both align with each other then after it then place the belt.then it is set.

Aug 16, 2009 | 1995 Honda Accord

1 Answer

Timing belt settings


the tension setting for the belt?

or the timing marks? the timing marks differ. best set cyl. no 1 to tdc.. take out no. 1 spark plug and put sumthin long and thin down the hole.. like a long quarter drive extension.. and check to see that cyl 1 is at tdc.. then set your cam to the OT marks marked on the cam pulley and rocker cover... then you have to set the distributor also.. slacken the 13mm bolt for the dizzy clamp... you will find a line on the lip of the dizzy body.. this needs to align with the middle of rotor arm tip... (sumtimes a mark on the roror arm tip)... tension belt and your timing is set.. set your timing incorrectly and the car will run rough and not rev past 5k...

Sep 26, 2008 | 1993 Volkswagen Golf

Not finding what you are looking for?
2005 Volkswagen Polo 1.4i Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...