Question about Cars & Trucks

Open Question

TIMING MARKS FOR 2007 TATA INDICA 1.4 DLX DIESEL

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: mazda 6 timing marks

You are all fuckin thick. ask a question on here and get answers like this ********

Posted on Nov 06, 2008

alicantecoli
  • 22095 Answers

SOURCE: need the timing marks for a 3.1 td 5 cyl diesel injection pump

isusu engine?? have you looked for a 8mm hole in timing gear that corresponds with a hole on plate behind then lock it in with a bolt ,remove bolt after tightening belt .DONT FORGET THIS ???.....if you cant find anything do it with no timing marks easy --- piston no 1 at tdc valves closed spin pump till fuel comes out of no 1 injector feed and lock it all together,indirect diesel is 6/8 ,,,,,direct injection is 12/16,,,,and turbo is 18/22 btdc

Posted on Dec 13, 2008

  • 1 Answer

SOURCE: timing marks won't stay where they are put

theposition of the gears

Posted on May 31, 2009

michaelcanto
  • 76 Answers

SOURCE: Need timing marks 94 jetta 1.9l diesel any thoughts?

The timing marks are stamped into the steel pulley and flywheel and there should be a pointer attached to the engine. Degreasing the engine with GUNK and power washing it should uncover them.

I'm pretty sure it's crucial to have the engine timed to TDC as it relates to the end of compression/beginning of power stroke, and NOT the end of exhaust stroke.

With gas engines I do the following, to determine the TDC, by removing the #1 plug and insert a long straw, while turning the motor by hand watch for the maximum height of the straw, this will give you a TDC but knowing if its on the exhaust or compression stroke can only be determined if you were watching the closure of the intake valve indicating the begining of the next power stroke. Once you have this set look for the timing marks again. if you can't find them pick up a service manual at the library or autoparts store for photos and instructions.

Also check this site: http://forums.vwvortex.com

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tata indica tdi dlx ac blower 1,2,3 settings not working, only no 4 works


The blower rheostat is bad. Should be located in vent box on the passenger side under the glove box.

Nov 04, 2016 | Tata Indica Cars & Trucks

1 Answer

Need to know timing mark on tata indica 1.4 please


this is your engine
make sure you replace cam seal and timing cover seal

number one on TDC compression
after fitting new timing belt

turn motor by hand clockwise twice and mack sure the belt tension and timing marks are correct
26214915-wof0kwh1xpwidkmx23mdilgp-4-0.jpg

Jun 08, 2016 | Tata Cars & Trucks

1 Answer

What is firing order of tata indica 1.4


If it's a four cylinder the firing order is normally 1,3,4,2 hope this helps

May 07, 2015 | 2007 Tata Indica LEi

1 Answer

How do i check timing marks on tata indica lsi


The timing marks are notches on the engine block and all the pulleys that the belt goes around! Before removing the belt make sure all pulleys are in line with there mark! If not sure contact your local mechanic!

Dec 31, 2014 | 2006 Tata Indica LSi

1 Answer

What is tata indica lsi 1.4 cylinder torque settings?


Torque settings for a TDI DLX is (in nm) 29+49 minus 90 degrees +64nm. Hope this is helpful.

Jul 22, 2014 | Tata Indica Cars & Trucks

1 Answer

Diesel engine. In the morning when the vehicle had been standing for a day, when cranking the engine it will start smooth for a second and then splutters / running rough and not respond to the acceler


2 things cause these type of problem both are related to air is getting into injection system #1 loose or pin holes in hoses from fuel tank to injection pump #2 fuel shut off solenoid is fully seating allow drain back. back car up driveway or place rear tires on some ramps with a near full tank this should keep fuel in injection system see if it starts and runs better this way if so then test for these problems

Apr 29, 2014 | 2009 Tata Indica DLX

1 Answer

Tata indica Timing marks


On. An Indica petroll or diesel there aren't aany timing marks as to say, firstly remove cylinder head, then attach a power bar or ratchet with socket to to bolt on crank shaft pulley. Rotate the engine anti-clockwise until piston one is at TDC (highest point it can go). Then at Te front of engine halfway down the block where engine meets bell housing there is a hole to. Insert a 8mm long bolt, this will lock the crankshaft. On the head on the cam shaft end cap is a hole, insert a screwdriver to fit and rotate cam with. A ratchet until the screwdriver slots in place and the cam cannot move. Replace the head, torque the bolts, fit the timing belt and tension it. Once this is done remove the locking bolt and screwdriver, Replace the cam-tappet. Cover and start the engine

Apr 04, 2014 | 2006 Tata Indica LSi

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

557 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...