Question about Cars & Trucks

Open Question

How to replace camshaft position sensor 2006 sorento

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: How do I replace a camshaft position sensor on a 2000 ford escort

bullshits, the CMP sensor is near the 4 injector, you have to take out all the electric conector near injector 4, take out the 2 screws that hold the fuel rail, sometimes you have to take out the 4 injector for the space, then take out the screws that hold the CMP, lub the o´ring of the new one and reverse this steps.

Posted on Oct 01, 2008

  • 55 Answers

SOURCE: replacing bad camshaft position sensor

  1. Disconnect battery ground cable.
  2. Remove water pump pulley attaching bolts, then the serpentine belt and water pump pulley.
  3. Disconnect sensor wiring connector and remove sensor retaining bolt.
  4. Twist and pull sensor to remove.
Reverse procedure to install and prior to installing new sensor, lubricate sensor O-ring.

It is located under the water pump. Make sure when you remove the sensor that you rotate the crank shaft and look in the hole to make sure the pick up magnet is still in there. Sometimes they come loose and cause a no start or long crank. You will need to have the code cleared still.

Posted on May 06, 2009

seans46
  • 161 Answers

SOURCE: check engine light is on. Code is related to camshaft position sensor. Where is the sensor located on a 1999 BMW 323is?

This is a normal problem and you need to replace it asap. The camshaft position determines when top dead center compression of the #1 cylinder occurs and the convertsit into a pulse signal that is sent to the pcm , then the pcm uses it to determine the correct injection sequence.

Posted on May 25, 2009

  • 113 Answers

SOURCE: OBD gave code for camshaft position sensor-how to replace?

haynes should have a manual on this car, which will show the location of the cam pos sensor. check autozone or napa

Posted on Jul 22, 2009

steve_e_uk
  • 1675 Answers

SOURCE: BMW X5 CAMSHAFT POSITION SENSOR A .SHOW DIAGRAM

hi i have a diagram if you would like it i could email it to you and there are 2 of them does it say which one it is? you can email me at
s.e.morris@hotmail.co.uk
and i will send you the diagram hope this helps

Posted on Mar 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix 2012 kia sorento camshaft sensor


replaced crank and cam sensor [Archive] - Sorento Nation - KIA ...

www.sorentonation.com/forum/archive/index.php/t-913.html

20 posts - ‎6 authors
replaced crank and cam sensors put back together cranked up very rough idle some tapping any ... 12-17-2012, 12:24 AM ... It's a 2006 3.5 Kia Sorrento. ... I found theproblem the SUV has a aftermarket alarm and remote start system I tripped ...

Kia Rio Crankshaft Position Sensor Replacement - YouTube

? 4:44
https://www.youtube.com/watch?v=hihQxMWuSFY
Mar 21, 2014 - Uploaded by Jason Roush
While looking for how to replace a Kia Rio crankshaft positionsensor, ... is on and i have a P0340 code, think this is theproblem? kia rio 2002.

Kia Sorrento/Sedona: 3.5 Litre Engine/Timing Belt/Crank ...

? 20:23
https://www.youtube.com/watch?v=CjaD_zYPrUA
Mar 29, 2014 - Uploaded by JamieJones TheCarMan
Repair and/or Replacement tips for timing belt, crank sensor,cam sensor, water pump and drivebelt ...

Crankshaft position sensor - 2003 Kia Sorento - RepairPal

repairpal.com > Questions > Kia > Sorento > 2003 Kia Sorento


Jan 20, 2016 | 2012 Kia Sorento Base 4dr SUV 2.4L 4-cyl....

2 Answers

Can you bypass a camshaft position sensor on a 2005 kia sorento. with out replacing it?


no you can`t because it will affect fuel and set codes in the computer.

Mar 19, 2015 | 2005 Kia Sorento 3.5

1 Answer

How to replace a camshaft sensor


2006 Saturn Ion Camshaft position sensor location:
The camshaft position sensor is located in the top left side of the valve cover.

Feb 10, 2015 | 2006 Saturn ION

1 Answer

How many camshaft and crankshaft sensors does my 2004 KIA Sorento have?


The camshaft position sensor is mounted on the engine near the camshaft gear by the ignition coils.The crankshaft position sensor is mounted on the engine near the crankshaft.

Nov 01, 2014 | 2004 Kia Sorento

1 Answer

I changed out the MAP sensor,and the idle air sensor on my 2006 Ford Taurus. This was before I had the fault code read at a dealer. Code came back as P0340, and P0430 Band 2 cat worn out. I had the cam...


P0340 FORD - Camshaft Position Sensor Circuit Bank 1 Sensor 1Possible causes- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
P0340 FORD Description The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection. The camshaft position sensor senses the retraction of camshaft (intake) to identify a particular cylinder. The camshaft position sensor senses the piston position. The sensor system consists of a rotating part, typically a disc, as well as a static part, the actual sensor.

When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.

When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals.
P0430, main catalyst is worn out.

Dec 04, 2012 | 2006 Ford Taurus

1 Answer

Location of camshaft position sensor for 2005 Kie Sorento


If it's an overhead cam, which I think it is, then it should be toward the very front of the engine, likely within the timing case. There should be some wires coming from it. It's usually a small black sensor.

Nov 12, 2012 | 2005 Kia Sorento 3.5

1 Answer

2006 hhr 2.4 won't start after replacing both camshaft position sensors.


Did you remember to plug in the MAF sensor? Are you sure the air chamber is correctly installed on the throttle body?

Feb 18, 2012 | 2006 Chevrolet HHR

1 Answer

2006 frontier camshaft position sensor


If you do not know where the Camshaft Position Sensor is located, then it would be safe to assume that you have not properly tested the sensor or the circuits that operate the sensor. Therefore, you cannot possibly know for sure that it even NEEDS to be replaced...so why are you looking to replace it?

Nov 20, 2011 | 2006 Nissan Frontier

1 Answer

2006 Kia Sorento code P0343 and P0463


did you ever get this fixed, i am having the same problem with mine, what was wrong with it

May 15, 2010 | 2006 Kia Sorento

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...