Question about Cars & Trucks

Open Question

Need a exploded view of 01 vw 2.8 litre passat timing marks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
robshow
  • 367 Answers

SOURCE: 2002 kia optima 2.4

www.kiatechinfo.com Sign up for login and you can locate any and all information there.

Electrical issue to you name it.

Posted on Jan 05, 2009

Ad
  • 1 Answer

SOURCE: Timing Marks on VW Jetta GL 1995 2.0 Litres

timing belt marks

Posted on Apr 21, 2009

  • 4102 Answers

SOURCE: I am having troubles locating

hi, here is a guide i have come across on this site written by another expert it should be the one for your engine but always double check.

If you are unsure what you are doing then please go out and buy a haines workshop manual as these tell you every detail you need to know so that would be your best solution.

Please dont do this work if your unsure what you are doing as you could damage the engine beyond repair so you have been warned;

it covers single cam and if you scroll down it shows double cam ok

Sep 14, 2009 - VW Passat & Audi A4 1990-2000 Repair Guide
Timing Belt - REMOVAL & INSTALLATION

2.8L SOHC (AFC) V6 Engine

  1. Note the radio security code and disconnect the negative battery cable.
  2. Place the (hood) lock carrier in the service position. For additional information, please refer to the following topic(s): Body And Trim, Service Position, Front Bumper, Hood Lock Carrier.
  3. Remove the engine accessory drive belt. For additional information, please refer to the following topic(s): General Information And Maintenance, Routing Maintenance And Tune-up.
  4. Turn the engine by hand to Top Dead Center (TDC) on the firing stroke for cylinder No. 1.
NOTE The large holes in the camshaft sprocket lock plates should be on the inside facing one another.
  1. Remove the Crankshaft Position (CKP) sensor from the lower left side of the engine block. Make sure the engine is at TDC and install the threaded crankshaft holding pin Tool No. 3242 and lightly tighten.
  2. Remove the upper timing belt covers, the crankshaft vibration damper and then the lower timing belt cover.
  3. Loosen the camshaft sprocket bolts slightly and use a suitable pulley to release the sprockets from the tapered ends of the camshafts.
  4. Loosen the tensioner roller and remove the drive belt.
To install :
  1. Install the timing belt over the sprockets, then the idler rollers and lastly over the tensioner.
  2. Install camshaft alignment tool holder Tool No. 3243 into the camshaft alignment flanges.
  3. Check and adjust the cam belt tension such that the upper left portion of the belt between the tensioner and the left cam gear can just be twisted 90° ( 1 / 4 turn).
  4. Tighten the cam belt tensioning roller to 33 ft. lbs. (45 Nm), and the camshaft sprocket bolts.
  5. The balance of the installation is in reverse order of removal.

2.8L DOHC 5V (AHA) V6 Engine
  1. Note the radio security code and disconnect the negative battery cable.
  2. Place the (hood) lock carrier in the service position. For additional information, please refer to the following topic(s): Body And Trim, Service Position, Front Bumper, Hood Lock Carrier.
  3. Remove the engine accessory drive belt. For additional information, please refer to the following topic(s): General Information And Maintenance, Routing Maintenance And Tune-up.
  4. Turn the engine by hand to Top Dead Center (TDC) on the firing stroke for cylinder No. 1.
NOTE The large holes in the camshaft sprocket lock plates should be on the inside facing one another.
  1. On the cylinder block near the crankshaft, remove the sealing plug from the lower left side of the engine block. Make sure the engine is at TDC and install the threaded crankshaft holding pin Tool No. 3242 and lightly tighten.
  2. Remove the upper timing belt covers, the crankshaft vibration damper and then the lower timing belt cover.
  3. Loosen the camshaft sprocket bolts slightly and use a suitable pulley to release the sprockets from the tapered ends of the camshafts.
  4. Using a 8mm Allen® wrench, rotate the timing belt tensioner roller clockwise until the tensioner is compressed; then, insert a 2mm spring pin through the tensioner housing and tensioner plunger to secure it in place. When the plunger is secure, release the wrench tension.
  5. Remove the damper-to-crankshaft bolts and the damper.
NOTE It is not necessary to remove the center bolt when removing the crankshaft damper.
  1. Remove the serpentine belt idler and the crankshaft damper guard.
  2. Mark the running direction of the timing belt and remove it from the pulleys.
58637f8.jpg

Fig. Crankshaft pulley alignment location for TDC-Audi 2.8L V6 engines


d58d8c0.jpg

Fig. Left camshaft sprocket alignment position for TDC; right camshaft position is similar-Audi 2.8L V6 engines


934cbaf.jpg

Fig. View of crankshaft holding tool installed-Audi 2.8L V6 engines


9091ff0.jpg

Fig. View of camshaft locator bar installed-Audi 2.8L V6 engines


To install:
  1. Make sure that the camshaft pulleys and the crankshaft pulley are in alignment with TDC of the No. 1 cylinder's compression stroke.
  2. Install the timing belt; make sure the timing belt is installed in the correct running direction from which it was removed.
  3. Using a 8mm Allen® wrench, rotate the timing belt tensioner roller clockwise until the tensioner is compressed; then, remove the 2mm spring pin from the tensioner housing. Slowly, release the tensioner spring pressure to put pressure on the timing belt.
  4. Install the crankshaft damper guard and the serpentine belt idler pulley; torque the idler pulley bolts to 33 ft. lbs. (45 Nm).
  5. Install the crankshaft damper and torque the damper-to-crankshaft bolts to 15 ft. lbs. If the damper-to-crankshaft center bolt was removed, torque it to 147 ft. lbs. (200 Nm) plus 180° 1 / 2 turn).
  6. Remove the Crankshaft Holder tool No. 3242 and install the sealing plug.
  7. Replace the remaining components by reversing the removal procedures.
  8. Refill the cooling system and the automatic transaxle. Connect the electrical connectors. Install the negative battery cable last.
  9. Test drive the vehicle.

Posted on Jan 18, 2010

  • 617 Answers

SOURCE: How do you set the timing marks on a '99 VW passat

I have a diagram with pictures and directions for timing belt procedure, need email address to send to.

Posted on Feb 09, 2010

  • 1 Answer

SOURCE: need 2.0l 4-CYL ALIGNING CAMSHAFT/ TIMING MARKS

2005 vw jetta 2.0l timing marks

Posted on Feb 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2014 vw Passat 1.8l engine oil capacity how much oil


4.7 litres of 0-30 0w-40 or 5w-30 longlife oil

Feb 20, 2015 | 2014 Volkswagen Passat

1 Answer

I purchased a 2003 late 52 plate vw passat 2.0 petrol 130 sport after a few days the oil light came on then i topped it up after two weeks of driving local i found i done a check and found it needed...


from the VW manual........"expect to use about 1 litre for every 500 km."the oil level should be checked every week".........some cars have a breather on the side of the block that needs cleaning every year.(looks like a metal canister about 2.1/2" tall by 4"wide with a hose to the inlet manifold/air cleaner).

Nov 20, 2010 | 2003 Volkswagen Passat

1 Answer

How many quarts of oil for an oil change on a 96 vw passat with a 2.8? changing filter also.


oil and filter change,about 3.1/2 litres(put in 2 then dip and fill to midway on dipstick....do NOT overfill.(with filter, jab a screwdiver though the side and unscrew it its easier.)

Sep 06, 2010 | 1996 Volkswagen Passat

1 Answer

For a 2008 vw Passat, is it normal to burn 2 qrts of oil between changes? 4 cyl 2 0 turbo


VW RECKON that oil usage around 1/2 litre per 500km is acceptable !!!!!!!! yeah right...i suppose it does lubricate the turbo blades....and the exhaust pipe internally....you could use 20/50 instead of 5/40 that would cut it down,but not do much good to the engines long life..... VW reckon about 150,000m before rebuild.

Aug 20, 2010 | Volkswagen Passat Cars & Trucks

1 Answer

VW Passat 1,9 tdi Automatic transm, 96Kw-2001/2 model Removed sump totaly, repaired it (smashed,leaking) drained oil.How much oil to fill, how to fill it, and how to measure (important?) VW says 6 litres,...


There is a small drain plug that needs to be removed, the car level, suspended on Jack's, monitor the tranny fluid temperature with obd2 tool, engine started from cold, , the fluid will ooze out of the open plug hole at proper temperature. Use a new plug when done topping the fluid. Intricate task

Oct 09, 2017 | 2002 Volkswagen Passat

1 Answer

Reset service interval alarm on VW Passat-01?


This is a mileage interval light that trips every 3,000 to 5,000 miles that indicates an oil change is necessary. You do not need a special tool to change your oil, nor do you need to bring the car in to the dealer.
1. Sit in the driver's seat of the Passat and close all the doors.
2. Position the trip/odometer button to display the odometer mileage reading, then hold it down with the forefinger on your left hand.
3. Turn the ignition key to the "key-on/engine-off" position to turn on all the power options for the Passat without actually starting the engine. At this point, a service indicator light will display (in the form of a wrench).
4. Press the minute adjustment button on the clock (or turn the knob clockwise on European manufactured Passats) and release the trip/odometer button.
Good luck and thank you using Fixya

Mar 15, 2010 | 2001 Volkswagen Passat

1 Answer

WHAT IS THE CAPACITY OF THE FUEL TANK IN MY VW PASSAT ESTATE 2004 HIGHLINE 130 DIESEL?


60 litres. 13.2 Imperial gallons or 15.85 US gallons. The next year's model has a 70 litre tank.

Feb 26, 2010 | 2004 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...