Question about Cars & Trucks

Open Question

2007 chevy Malibu passenger side airbag module out. need price

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jj127
  • 37 Answers

SOURCE: 2000 Chevrolet Malibu LS airbag problems

The passenger side airbag is a lot easier then driver side. Take the glove box out and you will see two 10mm bolts holding it in place. When you open the passenger side front door, remove the panel on the side of the dash and you will see yellow connectors.The 1 closest to the front is attached to the air bag, it is clipped into the frame. Just pull it loose and take it out and your done. For the Driver side, it takes a skinny T27 to remove the two star bolts, then just disconnect the horn red clip and ground and install new airbag. The module is located under the passenger seat, underneath the carpet. Kinda stupid but thats where its at. You also need to replace the front impact sensor located behind the grille on the back side of the metal bar to each side. Follow the hood latch down. Also just to make sure, you know to disconnect the battery before you do all this. You don't want new airbags to accidentally deploy.

Posted on Jun 20, 2009

Murphybanton
  • 2004 Answers

SOURCE: need estimate on 2001 chevy malibu( evap solonoid

Visit www.repairpal.com

Posted on Sep 27, 2009

  • 1986 Answers

SOURCE: Need to replace passenger side mirror of 2004 Chevy Malibu max

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

  • 134 Answers

SOURCE: NEED 2007 CHEVY MALIBU RADIO CODE

I just got the code for my radio by calling 1-800-537-5140 and choosing the option for my vehicle make. 1 for chevrolet. then i entered 106010 for the customer # and then entered my serial # from the stereo and it gave me a lock code for free. Now i am just trying to figure out how to enter it since my manual tells me to take it to the dealership. Now that you have your 4 to 6 digit code, you can enter it by following the these steps. 1. Make sure your ignition is in the "on" position, but no started. 2. Press/Hold the "HR" button to set the first 2 or 3 numbers. 3. Press/Hold the "Min" button to set the next 2/3 numbers. 4. Press the AM/FM button one time. "SEC" should be displayed. You can now turn the radio on. Good luck!

Posted on Oct 28, 2009

  • 3640 Answers

SOURCE: dtc code p0121 and p2135 2007 chevy malibu

both codes refer to the throttle position sensor, the sensor is at the throttle plate, on the side of the throttle body. to test remove the connector to sensor, use a ohms meter to test. put 1 lead to top connection and the other to the bottom one. move throttle and the needles on the ohms meter should move very even, move throttle slow to get a good reading, needle should move without no hesitation, if the test is bad replace tps sensor. if the sensor gets to bad, it can have an effect on transmission shifting. after fixing sensor have the light turned of with an obd2 scanner.

Posted on Feb 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is driver airbag still functional when passenger airbag light is on in a 2010 Chevy malibu?


Hello Collette,

(Owner Manual Page 2-68)
The passenger sensing system turns off the right front
passenger frontal airbag and seat-mounted side
impact airbag under certain conditions. The driver
airbags and the roof-rail airbags are not affected by the
passenger sensing system.
The passenger sensing system works with sensors that
are part of the right front passenger seat. The sensors
are designed to detect the presence of a properly-seated
occupant and determine if the right front passenger
frontal airbag and seat-mounted side impact airbag
should be enabled (may inflate) or not.

I'm not sure if a purse or other light weight objects would activate the passenger airbag but if your display is showing random passenger activation it would be best to have a qualified dealer check into it...better safe than sorry.
http://www.gm.ca/media/owners/manuals/2010_Chevrolet_Malibu_Manual_en_CA.pdf

Jul 19, 2016 | 2010 Chevrolet Malibu

1 Answer

How to get the airbag light to go off on a 2007 Chevy van Express


You need to find out what code or codes are stored in the airbag control module > There are a lot of components involved in your airbag system : If you haven't had any training on these systems your best bet is take it to a ASE certified repair shop . People have been killed messing with these systems not knowing what they were doing .
The frontal SIR system consists of the following components:
?€¢
AIR BAG indicator located on the instrument panel cluster (IPC)


?€¢
Driver and passenger knee bolsters


?€¢
Inflatable restraint front end sensor


?€¢
Inflatable restraint PASSENGER AIR BAG ON/OFF indicator located on the instrument panel


?€¢
Inflatable restraint Passenger Presence System (PPS)


?€¢
Inflatable restraint I/P module


?€¢
Inflatable restraint I/P module disable switch


?€¢
Inflatable restraint seat position sensors (SPS) (left/right)


?€¢
Inflatable restraint sensing and diagnostic module (SDM)


?€¢
Inflatable restraint steering wheel module


?€¢
Inflatable restraint steering wheel module coil


?€¢
Inflatable restraint wiring harnesses


?€¢
Seat belt pretensioners (left/right)


?€¢
Steering wheel and column

Nov 22, 2015 | Cars & Trucks

1 Answer

How to remove front passenger side seat


Always disable the air bag system first, to prevent accidental deployment of the air bags. The main airbag module is beneath carpeting under passengers seat. To remove passengers seat, At the rear of the seat remove the two bolts securing the tracks to the floor, tilt the seat up and towards the instrument panel, unplug any electrical connectors beneath and remove the seat. the front plastic track covers can remain in place while the seat track tabs are lifted out of the slots on the floor. ( caution disable airbag before removing the seat ) Good-Day! Hope this helps you!

Sep 12, 2014 | 2000 Chevrolet Malibu

1 Answer

2007 chevy malibu airbag module


I don't know but my first check would be on youtube.

Apr 01, 2014 | 2002 GMC Envoy

1 Answer

Where is the fuse for the front passenger side airbag on a 2007 Chrysler Town and Country?


The air bags are powered thru the airbag control module.
The module gets power from two fuses in the box near the battery.

Feb 28, 2013 | Cars & Trucks

2 Answers

Location of module


The Sensing diagnostic module is under the passenger seat under the carpet

Jun 20, 2009 | 2003 Chevrolet Malibu

2 Answers

2000 Chevrolet Malibu LS airbag problems


The passenger side airbag is a lot easier then driver side. Take the glove box out and you will see two 10mm bolts holding it in place. When you open the passenger side front door, remove the panel on the side of the dash and you will see yellow connectors.The 1 closest to the front is attached to the air bag, it is clipped into the frame. Just pull it loose and take it out and your done. For the Driver side, it takes a skinny T27 to remove the two star bolts, then just disconnect the horn red clip and ground and install new airbag. The module is located under the passenger seat, underneath the carpet. Kinda stupid but thats where its at. You also need to replace the front impact sensor located behind the grille on the back side of the metal bar to each side. Follow the hood latch down. Also just to make sure, you know to disconnect the battery before you do all this. You don't want new airbags to accidentally deploy.

May 13, 2009 | 2000 Chevrolet Malibu

1 Answer

Airbag alarm


This should be for the passenger side airbag. If an adult is sitting in the passenger side seat and there is a light that says airbag off then you have a problem either with the passenger side airbag or with the passenger side seat detector. Start up the car and sit in the passenger seat, buckle the seat belt and make sure the light now says airbag on. If this does not happen take car to dealer. Dealers have correct computers to enter the airbag modules to read and diagnose the fault code.

Feb 28, 2009 | 2008 Toyota Camry

1 Answer

Disable onstar from 2007 chevy silverado


Call onstar and cancel the service, pull fuses, then remove the top of the dash and unhook the onstar module behind the passenger side airbag. I think it would be much easier just to call and cancel

Feb 19, 2009 | 2007 Chevrolet Silverado 1500 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...