Question about GMC Cars & Trucks

Open Question

Bolt torque specs 1999 Cadillac Deville oil pan

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

sledge1863
  • 149 Answers

SOURCE: 1999 Saab 9-5 oil pan torque spec

they should be torqued with a 3/8 torque ratchet to 30 inch pounds.

Posted on Mar 06, 2009

  • 158 Answers

SOURCE: 2000 sebring transmission pan torque spec

10 ft lbs no real patterm needed

Posted on Apr 03, 2009

moparownr
  • 667 Answers

SOURCE: Need torque specs for oil pan bolts

torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.

Posted on May 22, 2009

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

98 jeep wrangler tj 4.0 oil pan bolt pattern or layout. An torch specs


Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

May 21, 2016 | Jeep Cars & Trucks

1 Answer

What are the torque specs for the 5 bolts that secure the Transmission Manual Valve Position Pressure Switch


Torque specs on on 4L60 tranny pan in 04 escalade??

www.cadillacforums.com/.../cadillac-escalade.../260881-torque-specs-4l6...
May 26, 2012 - 3 posts - ‎3 authors Has 104000 miles on it now, figured it's time to change the filter and the fluid. ...Cadillac Escalade, EXT and ESV Forum - 1999 - 2006 Discussion, ... Flywheel toTorque Converter Bolt ... Transmission Fluid Pressure Manual Valve Position Switch to Valve Body Bolt ... Powered by vBulletin® Version 4.1.5 Re: SRX V8 Valve Cover Gasket Replacement Write Up ...
14 posts
Jun 10, 2015
2000 DTS Setting up Internal Mode Switch - 4T80E ...
9 posts
Aug 27, 2014
More results from www.cadillacforums.com

Nov 19, 2015 | 2000 Cadillac Escalade

1 Answer

How to remove oil pan


jack it up, drain oil from drain plug on oil pan when drained remove and replace oil filter also. remove the pan bolts pull off pan and gasket.put new oil pan gasket on if needed.when oil pan bolts are back in, screw them in hand tight, then torque them down to specs and alter nate the tightening so it wont damage pan seal. any auto parts store can tell you the torque on the bolts for your car. good day!

Mar 31, 2014 | 1999 Chevrolet Venture

1 Answer

What is a 2000 deville oil pan bolts torqued too?


Hello Tommy, recommended oil pan bolt torque is 128 inch-pounds.
I hope this helps.


11_17_2011_8_56_56_pm.jpg

Nov 17, 2011 | 2000 Cadillac DeVille

1 Answer

How hard is it to install oil pan on my 2000 deville, northstar engine


I worked on a 1999 Deville and to remove the oil pan wasn't to bad to change. All I had to do was Jack up the car and support it.Also remove the negative battery terminal.Drain the oil then remove the torque converter cover bolts and then the oil pan bolts and remove the oil pan.On some model Cadillacs there is also an exhaust cross under pipe that also has to be removed.Be sure not to over tighten the oil pan bolts there real hard to get out if you break one.Your going to have to find out how tight they should be because they all very depending on the vehicle.Most all of your auto parts stores have this information.

Feb 25, 2011 | 2000 Cadillac DeVille

1 Answer

How to replace oil pan gasket on 2002 deville


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Oct 29, 2010 | 2002 Cadillac Deville

1 Answer

Need the torque specs and sequence for the engine oil pan 1999 potiac sunfire 2.4


Torque on the oil pan bolts is 18 lb/ft. Tighten in a criss cross pattern slowly tightening the bolts down making multiple passes until you have them torqued.

Jul 15, 2010 | 1999 Pontiac Sunfire

2 Answers

What are the cylinder head torque specs for a 1999 cadillac deville 4.6l


I can help you with this but I have to ask one question. Have you already taken this apart and putting it back together? Did you rethread all the head bolt holes because they strip out when you tighten them and you will ruin the head gaskets. Let me know, I have don't this job quite a few times. I'll have to look up the actual torque specs. Also you are wanting the spec for the cylinder head bolts and not the cylinder head cover bolts right?

Jun 12, 2010 | 1999 Cadillac DeVille

1 Answer

1999 Saab 9-5 oil pan torque spec


they should be torqued with a 3/8 torque ratchet to 30 inch pounds.

Mar 06, 2009 | 1999 Saab 9-5

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...