Question about Mazda Cars & Trucks

Open Question

Air bag problem body code b1886 - Mazda Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi i have just changed steering wheel on fiesta zetec 2003 for a ST150 2005 steering wheel will the air bags and connections be compatable with each other.


. Were did you check for codes ? an what are you checking with ? you need a factory scan tool to check for those type codes ? or the light flashes codes
Lamp Fault Code (LFC)
When the RCM detects a fault, it will cause the air bag indicator to flash a coded sequence called a LFC. The code is one digit. The digit is indicated by a number of flashes with a 0.5 second interval between pulses. There is a 5 second pause between each display of an LFC.
Each LFC is flashed five times after which the air bag indicator will remain lit as long as the key remains in the RUN position. If there are multiple LFCs, each LFC will flash in order of priority.
Each LFC has one or more associated DTC.
  1. Press TRIGGER. The RCM will run the On-Demand Self-Test and display On-Demand DTCs (reflecting hard system concerns) on the screen.


Restraints Control Module (RCM) DTC Index DTC LFC LFC Priority Description Action - Continuous 1 Air bag warning indicator is illuminated continuously Go To Pinpoint Test B . B1231 Continuous 3 Longitudinal acceleration threshold exceeded (Crash Occurred) Go To Pinpoint Test C . B1318 Continuous 4 Battery voltage low REFER to Section 414-00 . B1342 Continuous 2 RCM is defective DIAGNOSE and REPAIR other DTC(s) that are present. CLEAR the DTCs. REPEAT the self test. When or if DTC B1342 alone is present, INSTALL a new RCM. REFER to Restraints Control Module (RCM) in this section. CLEAR the DTCs. REPEAT the self test. B1462 N/A N/A Safety belt switch circuit failure Go To Pinpoint Test AN . B1869 Continuous or Tone 39 Lamp air bag warning indicator circuit open Go To Pinpoint Test AJ . B1870 Tone 41 Lamp air bag warning indicator circuit short to battery Go To Pinpoint Test AK . B1876 4 24 Safety belt driver pretensioner circuit failure Go To Pinpoint Test T . B1877 4 23 Safety belt driver pretensioner circuit open Go To Pinpoint Test S . B1878 4 22 Safety belt driver pretensioner circuit short to battery Go To Pinpoint Test R . B1879 4 36 Safety belt driver pretensioner circuit short to ground Go To Pinpoint Test AF . B1880 4 27 Safety belt passenger pretensioner circuit failure Go To Pinpoint Test W . B1881 4 26 Safety belt passenger pretensioner circuit open Go To Pinpoint Test V . B1882 4 25 Safety belt passenger pretensioner circuit short to battery Go To Pinpoint Test U . B1883 4 38 Safety belt passenger pretensioner circuit short to ground Go To Pinpoint Test AH . B1885 4 37 Safety belt driver pretensioner circuit resistance low on squib Go To Pinpoint Test AG . B1886 4 39 Safety belt passenger pretensioner circuit resistance low on squib Go To Pinpoint Test AI . B1915 3 10 Air bag driver circuit failure Go To Pinpoint Test F . B1916 3 8 Air bag driver circuit short to battery Go To Pinpoint Test D . B1920 3 13 Air bag passenger circuit failure Go To Pinpoint Test I . B1925 3 11 Air bag passenger circuit short to battery Go To Pinpoint Test G . B1932 1 9 Air bag driver circuit open Go To Pinpoint Test E . B1933 2 12 Air bag passenger circuit open Go To Pinpoint Test H . B1934 1 29 Air bag driver inflator circuit resistance low on squib Go To Pinpoint Test Y . B1935 2 31 Air bag passenger inflator circuit resistance low on squib Go To Pinpoint Test AA . B1936 3 28 Air bag driver circuit short to ground Go To Pinpoint Test X . B1938 3 30 Air bag passenger circuit short to ground Go To Pinpoint Test Z . B1992 5 14 Driver side, side mount air bag circuit short to VBATT Go To Pinpoint Test J . B1993 5 32 Driver side, side mount air bag circuit short to ground Go To Pinpoint Test AB . B1994 5 15 Driver side, side mount air bag circuit open Go To Pinpoint Test K . B1995 5 33 Driver side, side mount air bag low resistance on squib Go To Pinpoint Test AC . B1996 6 17 Passenger side, side mount air bag circuit short to VBATT Go To Pinpoint Test M . B1997 6 34 Passenger side, side mount air bag circuit short to ground Go To Pinpoint Test AD . B1998 6 18 Passenger side, side mount air bag circuit open Go To Pinpoint Test N . B1999 6 35 Passenger side, side mount air bag low resistance on squib Go To Pinpoint Test AE . B2117 5 16 Driver side, side mount air bag low capacitance on squib Go To Pinpoint Test L . B2118 6 19 Passenger side, side mount air bag low capacitance on squib Go To Pinpoint Test O . B2141 5Hz 6 NVM configuration failure RECONFIGURE the RCM. REFER to Section 418-01 . B2226/ B2227/ B2855/ B2856 N/A N/A Front crash sensor failure Go To Pinpoint Test AR . B2228/ B2230/ B2232/ B2234 N/A N/A Air bag driver, 2nd stage fault Go To Pinpoint Test AL . B2229/ B2231/ B2233/ B2235 N/A N/A Air bag passenger, 2nd stage fault Go To Pinpoint Test AM . B2433/ B2434/ B2435 N/A N/A Buckle switch, driver failure Go To Pinpoint Test AO . B2437/ B2438/ B2439 N/A N/A Buckle switch, passenger failure Go To Pinpoint Test AP . B2477 Continuous 7 Module configuration failure Check for correct RCM for this vehicle. RECONFIGURE the RCM. REFER to Section 418-01 . B2853/ B2854/ B2873/ B2873/ U2027 5 20 Left side crash sensor internal fault/short to ground/VBATT/ID fault Go To Pinpoint Test P . B2852/ B2874/ B2875/ U2028 6 21 Right side crash sensor internal fault/short to ground/VBATT/ID fault Go To Pinpoint Test Q . C1947/ C1948/ C1982 N/A N/A Seat track position sensor, driver failure Go To Pinpoint Test AQ .

Oct 14, 2015 | Cars & Trucks

1 Answer

Why does the air bag light come on


You need to have a repair facility check for codes in the BODY computer to verify, but I believe your CLOCK spring, located in the steering column beneath the steering wheel is bad. This clock spring allows continuity between the air bag and air bag system when the steering wheel is turned. You are experiencing momentary breaks in the circuit when the steering wheel is turning and the body computer is sensing this and is setting off the air bag light and the beeper alarm. A body code will verify this. It is not a major job to replace the clock spring and involves pulling the steering wheel off to access it.

Aug 09, 2014 | 2004 Chrysler PT Cruiser

1 Answer

Srs light on 52 plate proton wira keeps flashing


And you checked for codes,as with any
vehicle problem in the last 30 years, since
we had those electronic systems?

Googled your codes, to see what system may have
an issue?

SRS --is air bag,seat belts, etc

Not likely the air bags are turned on for now

Need a shop with the proper scan tool to get the codes
from body modules

Jul 15, 2014 | Cars & Trucks

1 Answer

Turn off airbag light


Air bag lights self reset you still have a existing problem during the self test it has detected a open/shorted circuit disabling the system. watch your air bag light then turn key on do not start engine lamp comes on then goes out and then comes back on again. this is the start up initialization of the system and sensor or wiring does not pass the system goes fail safe. with a scanner the air bag code can be read thru the OBDii connector if having hyundai body control software.

Mar 21, 2014 | 2003 Hyundai Santa Fe

1 Answer

Air bag light


some of the smaller obd ll readers are not capable of reading b [body]or c [chassis] codes and usually some of the airbag codes are b codes most auto stores that do the free code checks use a higher end reader and can give u code for problem a lot of the problems are usually from the front sensors under bumper that get covered and corrosion from the elements

Apr 14, 2013 | GMC Savana Cars & Trucks

1 Answer

Air bag light is on constantly


If the warning light stays on after the engine starts, the system is disabled.
You'll need to get the body computer scanned for trouble codes to proceed.

Feb 21, 2013 | 2005 Pontiac Vibe

1 Answer

1997 honda civic 1.6L DX SRS Air Bag light stuck on after drove throo heavy rain!


A code reader may not access the body computer, but a professional scanner should. You may be able to research the air bag system online and find a way to make the light flash the codes.
I would guess after reading your description one of the front crash sensors got water in the connector and the sensor has failed.

Sep 27, 2012 | Honda Cars & Trucks

1 Answer

Where s the air bag light fuse


Bottom line is you can't.
Due to the safety factor, I don't know of a way to turn the light off without disconnecting the entire system.
When work is done on the steering wheel the fuse is removed that turns the light on.
You may have to get a shop manual to find the connectors to disconnect the air bag module.
The air bag module which is connected to the body computer requires a different kind of scanner than the engine computer to read it for codes.

Aug 18, 2012 | 1997 Chrysler LHS

1 Answer

Air bag light repair


Hello. I would love to help you, To know how to assist we need the codes from the body computer, Without them we can only tell you to start repacing expensive parts without warrant. Your linked to my email now, And i will help you as soon as you reply

Jun 18, 2010 | 1997 Pontiac Sunfire

1 Answer

Airbag light on. flashing 5 times 2 times then stays on


I think you have a false code stored due to your work. clear the code and you should be ok.
If the air bag indicator does not illuminate or the indicator stays on or flashes at any time, a fault has been detected by the air bag diagnostic monitor.
Diagnostic trouble codes (DTCs) may not be displayed for approximately 30 seconds after the ignition switch is placed in the RUN position. This is the amount of time the air bag diagnostic monitor requires to perform all tests and verify system faults.
Each DTC (a series of flashes and pauses of the air bag indicator):
  • Represents a two-digit number.
  • Is always displayed at least twice.
If the diagnostic monitor detects a fault in the air bag system, a diagnostic trouble code (DTC) will be written to the diagnostic monitor's Non-Volatile RAM (NVRAM). This DTC will then cause the lamp to flash a lamp fault code (LFC) on the air bag warning lamp and can be retrieved with the New Generation STAR (NGS) tester. After servicing the DTC may then be cleared from the NVRAM.
If a system fault is present and the air bag indicator is malfunctioning, an audible tone will be heard. The tone is a series of five sets of five beeps. If the tone is heard, the air bag system needs attention.
If a fault exists that makes unwanted air bag deployment possible, the air bag diagnostic monitor will attempt to remove deployment power by turning on a solid state switch to blow the 10A battery fuse.

If the 10A battery fuse has successfully been blown by the air bag diagnostic monitor, the air bag diagnostic monitor will not attempt to blow it again until the proper fault has been repaired and cleared (refer to Diagnostic Instructions). The air bag diagnostic monitor will store both the unwanted deployment diagnostic trouble code and the loss of deployment power diagnostic trouble code. The loss of deployment power diagnostic trouble code is the highest priority.
If a fault exists that makes unwanted air bag deployment possible, the air bag diagnostic monitor has an internal fuse that that will blow (open) automatically. This removes all power to the air bag deployment circuit.
DTCs are prioritized numerically. If two or more faults occur at the same time, the fault having the highest priority will be displayed first. After that fault has been corrected, the next highest priority fault will be displayed.
The air bag diagnostic monitor includes an internal backup power supply. This feature provides sufficient backup power to deploy the air bag in the event the battery (10655) or battery cables are damaged in a collision before safing and air bag sensors close. The backup power supply will deplete its stored energy approximately one minute after the positive battery cable is disconnected.
---------------------------------------------------------------
Once a DTC is logged into the air bag diagnostic monitor memory, it will stay in memory until 80 key cycles have been recorded or until the NGS is used to erase the DTCs. Once 256 key cycles have been recorded since the concern was last detected, the DTC will automatically be removed from memory.
--------------------------------------------------------------
Active Command Modes
This command allows the technician to verify operation of the air bag system, indicator and tone. When the air bag output command is executed, the indicator and the tone are simultaneously activated for approximately four seconds. Both devices are automatically deactivated.


Air Bag Diagnostic Monitor DTC Priority Table DTC LFC Description Action To Take B1342 24 Air bag diagnostic monitor is faulted (retrieved only during On-Demand Self Test) GO to Pinpoint Test P . B1867 12/52 Lost or low battery voltage GO to Pinpoint Test A . B1869 — No air bag indicator — inoperative indicator circuit GO to Pinpoint Test R . B1913 13/53 Air bag circuit shorted to ground — driver/passenger GO to Pinpoint Test B . B1914 14/54 Air bag sensor circuit shorted to ground GO to Pinpoint Test C . B1921 21 Air bag diagnostic monitor ground circuit open or not mounted to the vehicle properly GO to Pinpoint Test D . B1922 22 Safing sensor output circuit shorted to battery voltage GO to Pinpoint Test E . B1924 24 System disarm fault GO to Pinpoint Test P . B1932 32 Driver side air bag module circuit high resistance or open GO to Pinpoint Test F . B1933 33 Passenger side air bag module circuit high resistance or open GO to Pinpoint Test G . B1934 34 Driver side air bag module circuit low resistance or shorted GO to Pinpoint Test H . B1935 35 Passenger side air bag module circuit low resistance or shorted GO to Pinpoint Test J . B1941 41 RH air bag sensor feed/return circuit open GO to Pinpoint Test K . B1942 42 LH air bag sensor feed/return circuit open GO to Pinpoint Test L . B1944 44 RH air bag sensor not mounted to the vehicle properly or ground circuit open GO to Pinpoint Test M . B1945 45 LH air bag sensor not mounted to the vehicle properly or ground circuit open GO to Pinpoint Test N .
DTC - Diagnostic Trouble Code, retrieved using New Generation STAR (NGS) Tester.
LFC - Lamp Fault Code, flashed on air bag indicator.

May 21, 2009 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...