Question about 2007 Chrysler Pacifica FWD New Cars

Open Question

62te not reverse - 2007 Chrysler Pacifica FWD New Cars

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chrysler 200 2013 62te transmission with 3.6 V6 P0729 code and nothing else. Replaced oil/filter 2X and solenoid pack. All looks good. What is wrong?


code p 0729 refers to gear 6 --incorrect ratio===causes ---fluid level---wiring---TR( transmission ratio) sensor /switch---shift solenoids---transmission mechanical fault
the box is operational so no need for mechanical failure to figure in the diagnosis
if you never use 6th gear, it is possible that the solenoid may be a bit rust inside or a wire has failed from corrosion
at this point I would be checking wiring , connections and pins are not corroded and then consider the TR sensor / switch replacement

Apr 30, 2017 | Chrysler Cars & Trucks

1 Answer

We have a 2011 ford f350 and are trying to t/s the reverse lights. we checked the fuses. what else might it be. we cant find a diagram to the wiring.


In the BJB - battery junction box under the hood ,is a reversing lamp relay. Check it or try a known good one !an check fuse F70 10amp in the BJB .

Reversing Lamps

The reversing lamp system consists of the following components:

  • Rear lamps
  • Reversing lamp switch
  • PCM
  • BCM

When the transmission is placed in REVERSE (R), the BCM provides voltage to the reversing lamps. The reversing lamps are located within the rear lamp assemblies.
When the transmission is in REVERSE, the PCM (gasoline engine) or the Transmission Control Module (TCM) (diesel engine) sends a message over the High Speed Controller Area Network (HS-CAN) to the Body Control Module (BCM) indicating the transmission is in REVERSE. The BCM provides voltage to the reversing lamps when it receives the message that the transmission is in REVERSE and the ignition is in the RUN state. You could have a transmission range sensor problem , check to see if it is adjusted correctly ! Need to have a scan tool to make sure the BCM is receiving signal from the PCM . This is complex for someone who doesn't deal with or know about serial data communications ! All it is ,is electric inputs to a control module, then the control module configures it into data bits an bytes 1's an 0's then sends it out on the Data bus. The module that needs this info reads it an turns on the lights.This system can set codes in the bcm ,leading to a problem.

  • DTC B1277:11 (Reverse Lamp: Circuit Short To Ground) - a DTC that sets when the BCMdetects a short to ground from the reversing lamp output circuit.
  • DTC B1277:15 (Reverse Lamp: Circuit Short To Battery or Open) - a DTC that sets when the BCMdetects an open from the reversing lamp output circuit.
  • Could set codes in the PCM - powertrain control module for a transmission range sensor problem !
  • Jan 28, 2015 | Ford F-350 Cars & Trucks

    1 Answer

    The reverse gear is fine it's the reversing lights that go out when it goes in to reverse gear


    You say that the reverse lights go out when reverse gear is selected! At what point are they on? Before reverse is selected?

    Oct 25, 2014 | Cars & Trucks

    1 Answer

    How much transmission fluid does a 62te take


    The 62TE requires +4 ATF. There
    are many different blends of ATF that
    meet the +4 requirement (markings for
    +4 are clear on the labels).
    Service Fill Level: 5.5 qts/5.2L
    Total Unit Capacity: 9.0 qts/8.5L

    Jun 21, 2014 | 2001 Dodge Grand Caravan

    1 Answer

    I just purchased a 2011 T&C. There is no information in the owners info on the Pentastar engine or about the econo mode. What it does how it works and when do you use it or turn it off. Do you have...


    You've got a 283 hp pstar engine with a vehicle with all the accessories that you can ask for. Here is an excerpt from an internal chrysler memo regarding your vehicle.

    The Town & Country gets a new, simplified powertrain lineup for 2011. The new Pentastar 3.6-liter V-

    6 engine that produces a best-in-class 283 horsepower and 260 lb.-ft. of torque, yet delivers excellent

    fuel economy, powers the entire lineup. The Pentastar V-6 engine is mated to Chrysler Group LLC's

    62TE six-speed automatic transmission. Chrysler Group was the first manufacturer to offer a sixspeed

    transmission in a minivan, debuting on the 2008 Chrysler Town & Country. New for 2011 is a

    fuel economizer mode switch, a driver-selectable engine economy mode which assists drivers to
    maximize fuel efficiency while driving. All the economy mode really does is to take the transmission out of sort mode which means it will have lower shift points and not rev up and produce as much torque as it would otherwise that's all. You should get around 17mpg city and around 24 highway dependant on your driving habits. It is your personal preference whether you choose to use this function or not. Try using it in econo mode for 2 weeks and without for 2 weeks, to notice the difference while driving and fuel economy, then you can decide your preference. Nice vehicle

    Mar 03, 2011 | Chrysler Town & Country Cars & Trucks

    3 Answers

    My check engine light came on and i pulled the code po732. what does it mean?i have a 2007 chrysler pacifica awd. I'm lost can't find a manual


    Most part places will have manual's.

    Code - P0732 - Gear 2 incorrect ratio.
    Transmission problem. Could be a sensor, I would reset computer see if it come's back, if it does have it check out could cause major damage if not taken care of.

    Feb 03, 2010 | 2007 Chrysler Pacifica FWD New Cars

    1 Answer

    Have a 94 New Yorker when I put it in reverse I get a red R on the PRNDL and don't have reverse all other gears are green and work. What might be causing this?


    the reverse clutch in the trans is after failing.there are two clutch packs in trans for reverse,low/reverse and reverse clutch in overdrive unit,so where you have all foward gears the low/ reverse is ok the reverse clutch in od unit is most likely culpret

    Aug 08, 2009 | 1994 Chrysler New Yorker

    1 Answer

    2005 Pathfinder no reverse lights


    On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced

    Apr 20, 2009 | 2005 Nissan Pathfinder

    1 Answer

    Reverse is gone on 1995 chevy blazer s10-goes forward just fine


    reverse clutch went out rebuild transmission

    Feb 21, 2009 | 1999 GMC Jimmy

    Not finding what you are looking for?
    2007 Chrysler Pacifica FWD New Cars Logo

    Related Topics:

    74 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    75817 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8180 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...