Question about Toyota Yaris

Open Question

Thermostat housing torque specs - Yaris Toyota Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
JShreader
  • 50 Answers

SOURCE: torque specs

Hello mikemcgee63, my name is JShreader. Thank you for choosing fixya.com.

The Torque Specs for the Thermostat Housing are 10 Nm (89 inch lbs.).

I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!

Posted on Apr 01, 2009

Ad
97F350diesel
  • 1326 Answers

SOURCE: what is torque spec for 2004 Ford 4.0 thermostat

Normally these bolts are about 20-24ft lbs. You don't want to over tighten them as they should have a rubber washer/gasket to help provide a good seal. These cast aluminum housing will easily strip so just use care when tightening. Just snug both bolts and run the vehicle til it reaches operating temp then check for leaks. You can also purchase a Chiltons/Haynes manual for your vehicle at any auto parts store for $15 they normally give you the torque specs as well as some other valuable tipe

Posted on Aug 06, 2009

emissionwiz
  • 76846 Answers

SOURCE: what are the thermostat hsng. torque specs for a chevy s-10 2.2L?

the thermostat is located at the connection of the upper radiator hose to the engine, pull the hose off at the engine and remove the hose connector cover that the hose is clamped to, the T-stat is under that cover.

Posted on Oct 28, 2009

  • 14036 Answers

SOURCE: what is the torque spec for the thermostat housing

THERMOSTAT HOUSING BOLT TORQUE IS 15 - 22 FT LBS.

Posted on Jul 11, 2010

emissionwiz
  • 76846 Answers

SOURCE: Torque specs 2003 Saturn vie thermostat housing

12-14 ft pounds, but just tighten down evenly never ever torqued the bolts for this kind of part.

Posted on Jan 24, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for 01 Honda Civic 1.6L VTEC to include intake , exhaust, thermostat housing to head cam pully


try referring to the repair manual. usually always has torque specifications:
http://www.papertownspdf.com/downloads/honda-civic-repair-manual-2000-2005/

Dec 30, 2016 | Honda Cars & Trucks

2 Answers

1995 ford windstar thermostat housing bolt torque spec


Most people don't bother using a torque wrench to tighten a thermostat housing.

It is more important to be careful and tighten each bolt a little at a time. You do not want to warp, crack, miss align the part you are bolting.

It does not take a lot of torque to seal a thermostat housing. I would guess somewhere between 15 and 20 ft lbs.

It is often hard to find such torque specs for specific vehicles.

For bolts that you cannot find a specified torque spec, you can refer to a standard bolt torque chart. The charts are based on the diameter of the bolt threads not the wrench size used to fit the bolt head. The charts also depend on the hardness of the bolt material. Also keep in mind the material you are bolting into.

Here is one such chart...
http://www.dansmc.com/torque_chart.htm

Keep in mind that thermostat housing bolts are just sealing a gasket. They are not holding the entire car together.

After turning wrenches for many years, most mechanics just know by feel.

There are cases where a torque wrench is mandatory. Like head bolts, wheel bearing/hub nuts, rod caps, main bearing, etc.

Jul 16, 2014 | Ford Windstar Cars & Trucks

1 Answer

Replace termastat 97 tracker 4 cylinder


follow the upper radiator hose to the piece on the engine where it connects. this is the thermostat housing. remove the housing clean both surfaces replace the thermostat making sure to orient the thermostat the same way as the original. install gasket using water rated gasket seal and torque the bolts to specs. let set for several hours, refill radiator, and presto

Jul 04, 2014 | Cars & Trucks

1 Answer

What are the torque specs for a 2003 Chevrolet trailblazer thermostat housing?


The 2003 Chevrolet Vortec 5300 generated 285 horsepower at 5,200 rpm and 325 ft.-lbs. of torque at 4,000 rpm. --------------------------------------------------------------
VVDI VAG Vehicle Diagnostic

Mar 26, 2013 | Cars & Trucks

1 Answer

Torque specs 2003 Saturn vie thermostat housing 3.0 v6


12-14 ft pounds, but just tighten down evenly never ever torqued the bolts for this kind of part.

Jan 24, 2012 | 2003 Saturn VUE

1 Answer

2003 zx2 thermostat housing seal


Be sure the surface is nice and clean. Don't over tighten your screws. There is a torque spec for that particular set up, so you need to find out what the torque spec is and don't go past that. Next make sure you don't use any kind of silicone or form a gasket. Just use the O-ring on clean surfaces.

Nov 14, 2017 | Ford ZX2 Cars & Trucks

1 Answer

What is the torque spec for the thermostat housing


THERMOSTAT HOUSING BOLT TORQUE IS 15 - 22 FT LBS.

Jul 11, 2010 | 1998 Lincoln Town Car

1 Answer

What is torque spec for 2004 Ford 4.0 thermostat cover bolts? Replaced black ''plastic'' thermostat housing and inlet cover. Thanks


Normally these bolts are about 20-24ft lbs. You don't want to over tighten them as they should have a rubber washer/gasket to help provide a good seal. These cast aluminum housing will easily strip so just use care when tightening. Just snug both bolts and run the vehicle til it reaches operating temp then check for leaks. You can also purchase a Chiltons/Haynes manual for your vehicle at any auto parts store for $15 they normally give you the torque specs as well as some other valuable tipe

Aug 06, 2009 | 2004 Mercury Mountaineer

1 Answer

Torque specs


Hello mikemcgee63, my name is JShreader. Thank you for choosing fixya.com.

The Torque Specs for the Thermostat Housing are 10 Nm (89 inch lbs.).

I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!

Mar 30, 2009 | 2001 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...