Question about Nissan Altima

Open Question

Evap canister vent valve

Error code 1446

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 275 Answers

SOURCE: 2004 Pontiac Grand Prix Evaporative Canister

you should be able to fix it look for a can near the fuel tank that has vacuum hoses coming out of it and you should be able to just buy the bad solenoid

Posted on Nov 03, 2008

  • 1 Answer

SOURCE: OBD code P0499, P0499 NVLD Canister Vent Valve Solenoid, Cause?

its above ur fuel tank from what i kno of but it could be ur canister or just a short in the wire to ur solenoid

Posted on Jan 17, 2009

savdragon
  • 37 Answers

SOURCE: Mustang GT 4.6 EVAP Canister Purge Valve Location?

You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Brett

Posted on Mar 19, 2009

  • 104 Answers

SOURCE: I have a 2004 Avalanche, 49K mileage, code PO446,

That is an EVAP code. its a vent control code. you can manually test it by powering it up if you know where its at. i cant remember exaclty where its at off the top of my head but its only 2 wires. using a volt meter you want to make sure power is getting to it, but you cannot activate it without dealer scan tool.hmmm if you can figure out which is ground and power when you give it 12 volts it should click. meaning your vent solenoid works and you have wiring problems or its leaking.

EVAP problems are hard to finde with out scanners. you can change the vent solenoid and hope it fixes it. but a code points you to the direction of a problem. hopefull its not wiring problems. in the northern states with snow. ice can pull out wires and also get clogged in the vent solenoid and lock it up. its either wiring or bad or a leaking solenoid. check condition of wires. if they look good try a vent soleniod.

if that doesnt fix it after a engine light reset and 2 weeks or so. then goto dealer. you need to reset it after repair. light will not go off on its own.GOOD LUCK

Michael
ASE certified.
plz rate

Posted on Apr 29, 2009

matney68
  • 426 Answers

SOURCE: Looking for the evap canister vent valve on a 2006 Silverado

if you look underneath the vehicle on drivers side in the area beneath drivers you with see a plastic rectangular sort of shaped box this is evap canister and vent valve is there in this area.

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007. What are the probable causes of DTC P0446?


DTC P0446: Evaporative Emissions (EVAP) Vent System Performance
Circuit/System Description
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inch H2O in a calibrated time, this DTC sets.
Diagnostic Aids
?€¢
An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent solenoid valve inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill problem.


?€¢
An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.


?€¢
An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission Canister Replacement .


?€¢
Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system


Do you have a scan tool that reads data PID'S ?
Your FTP - fuel tank pressure sensor could be at fault !

    Ignition ON and fuel cap removed, verify that the FTP sensor parameter is between 1.3-1.7 volts. ?‡'
    If not within the specified range, go to the FTP sensor section in Circuit/System Testing.

  1. Install the fuel cap.
  2. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 12 inches H2O.
?‡'
If the fuel tank vacuum is greater than the specified range, go to the restriction section in Circuit/System Testing.



If

Sep 06, 2015 | Chevrolet Impala Cars & Trucks

3 Answers

WHAT DOES FAULT CODE P1446-00 MEAN


older nissan? evap canister purge fault. check for loose or rotten/disconnected vacuum hoses before testing the vapor canister purge valve.
25439609-xipalmoknr3fbjmp51kycajc-2-0.jpg The charcoal canisters also clog up. Do some diagnosing before you go changing parts.

Feb 16, 2015 | Cars & Trucks

1 Answer

Toyota echo won't start code 440 441 446


Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

Feb 25, 2013 | 2002 Toyota ECHO

1 Answer

I have nissan xtrail 2005 code p1446 what is my problem


Trouble Code: P1446

EVAP Canister Vent Valve Malfunction (Closed)

Possible Causes:


EVAP canister vent control valve is damaged or has failed.EVAP canister vent control valve rubber tube is blocked.EVAP control system pressure sensor is damaged or has failed.EVAP water separator is damaged or has failed.EVAP canister is saturated with water.Click here to see the suspected parts to check out.

Jan 29, 2013 | 2005 Nissan X-Trail 2.5i

1 Answer

Code p1448


P1448 NISSAN - EVAP Canister Vent Control Valve Open

Possible causes- EVAP control system pressure sensor and the circuit
- Blocked rubber tube to EVAP canister vent control valve
- EVAP canister vent control valve
- Water separator
- EVAP canister is saturated with waterWhen is the code detected?EVAP canister vent control valve remains open under specified driving conditions.

Jun 08, 2012 | 1998 Nissan Frontier

2 Answers

P 2138 code with service engine soon light on?


Accelerator Pedal Position Error.

P2138 - Accelerator Pedal Position Sensor Circuit Range / Performance Problem

Clear the code - if it recurs, change the sensor.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 15, 2010 | 2006 Nissan Altima

3 Answers

Po446 evap vent code where is the evap vent located


Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine
  1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
  2. Disconnect the vacuum pipe from the EVAP canister purge valve.
  3. Disconnect the purge pipe from the EVAP canister purge valve.
  4. Remove the EVAP canister purge valve and bracket.
  5. Remove the EVAP canister purge valve from the purge bracket.
  6. Inspect for carbon release in the EVAP canister purge valve ports.
To install:
  1. Install the EVAP canister purge valve on to the purge bracket.
  2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
  3. Connect the purge pipe to the EVAP canister purge valve.
  4. Connect the vacuum pipe to the EVAP canister purge valve.
  5. Connect the EVAP canister purge valve harness connector.
  6. Remove the air cleaner outlet resonator.
  7. Disconnect the EVAP canister purge valve harness connector.
  8. Disconnect the engine purge pipe from the EVAP canister purge valve.
  9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
  10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
  11. Remove the EVAP canister purge valve along with the mounting bracket.
  12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines
  1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
  2. Remove the rear purge pipe from the EVAP canister purge valve.
    NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
  3. Disconnect the EVAP canister purge valve electrical connector.
  4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
  5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
  6. Remove the bracket.
To install:
  1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
  2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
  3. Connect the EVAP canister purge valve electrical connector.
  4. Connect the rear purge pipe to the EVAP canister purge valve.
  5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines
  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.
To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Hope this help (remember commetn and rated this).

Apr 21, 2010 | 2000 GMC Jimmy

2 Answers

P0441 EVAP Control System Incorrect Purge Flow


Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Evaporative Emission (EVAP) Canister Purge Regulator Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Sealing faulty.
Pipes between Tank Breathing and Throttle Body leaky/blocked.
Hose connection(s).
Intake leak.
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.
VSV connector near air filter box disconnected.

Jun 15, 2009 | 1996 Chevrolet Monte Carlo

1 Answer

My taurus failed due to code p0442 ecap emiss ctl sys leak detected (small leak)


    Continuous Memory Diagnostic Trouble Code (DTC) P0442 indicates that a fuel vapor leak has been detected [as small as 0.10 cm (0.04 inch)] in the Evaporative Emission (EVAP) system.
    Note: Prior to performing the following diagnosis inspect the Canister Vent Solenoid (CV) for contamination. A situation may exist where contamination holds open the Canister Vent (CV) solenoid enough to set DTC P0442 and also plugs the port to atmosphere enough to keep system from being vented quickly.
    • After market parts and accessories nonconforming to the EVAP system specifications.
    • Damaged, cross threaded or loosely installed fuel filler cap.
    • Small holes or cuts in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister outlet tube or EVAP return tube) in the EVAP system.
    • Loose fuel vapor hose/tube connections to EVAP system components.
    • EVAP system component [EVAP canister purge valve, fuel tank pressure (FTP) sensor, canister vent (CV) solenoid, fuel vapor control valve tube assembly or fuel vapor vent valve assembly] seals leaking.
    • CV solenoid partially open when commanded closed.
    • EVAP canister leaking.
  • Check for presence of fuel filler cap.
  • Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
  • Visually inspect for cut or loose connections to fuel vapor hoses/tubes in following locations:
    • EVAP canister to EVAP canister purge valve.
    • EVAP canister to fuel vapor vent valve assembly.
    • fuel vapor control valve tube assembly to fuel tank (if applicable).

Jun 26, 2008 | 1997 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...