Question about Cadillac SRX

Open Question

Where are jumper cables located in a cadillac srx?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Posted on Jan 25, 2009

  • 5 Answers

SOURCE: where is the oil filter located on a cadillac srx

Directly under the engine. You'll see a large smooth portion under there that looks like the underside of a bath tub and on the lowest portion of that is a bolt. Thats your oil reservoir where you drain your oil. The filter should be located near that pointing toward the front of the vehicle. GM OEM filters are usually black but could be white and are almost always 3" filters so a filter wrench that fits a 3" filter will get it off without problem.

Posted on Nov 13, 2009

Testimonial: "Thanks forn the help! This info has been hard to find from other sources. Again thanks!"

techbuster
  • 5081 Answers

SOURCE: rear liscese plate bulbs on 05 cadillac srx

First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch.
Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on.

Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.

Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.

Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.

OPTIONAL:
Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat.


Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.

The bulbs come in a two pack of cost $4.95 .

Posted on Nov 24, 2009

BCAS1298
  • 3092 Answers

SOURCE: where is cylinder #6 located

Looking at the front of the engine from where the serpentine belt is at, # 6 right side, back cylinder, right side 2-4-6, left side 1-3-5.

Posted on Aug 17, 2010

bluebirdmate
  • 1190 Answers

SOURCE: Where is the starter located

If your SRX has a Northstar V/8 engine the starter is under the intake manifold. The manifold has to be removed to access the starter. Hope this helps, thank you

Posted on Sep 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Location of the mass flow air sensor in a 2007 Cadillac SRX? how to replace?


Hard to believe you have a bad MAF in a 2007 caddy. How many miles on car? Have you tried cleaning the unit?

Parts store have a locator chart which should show location.

Apr 14, 2015 | 2007 Cadillac SRX

1 Answer

Where is the knock sensor located on a 2004 Cadillac srx v6 engine 3.6L


No sir, on the ly7 HFV6 3.6l in the 04-09 srx and cts the knock sensors are located on the sides of the engine block. Bank 1 and two are visible fringe wheel well. Not to hard to get to with a 3/8 drive 13mm socket, universal joint, and short extension. I would also check the connector with a multi meter while doing this job to ensure you have a good connection and harness is not damaged. Best of luck!

Mar 31, 2015 | 2004 Cadillac SRX

1 Answer

Where is my dipstick located on my 2006 srx cadillac


Hi Amber,
I presume that you want to change the oil on the Cadillac. The link below will tell you how to change the oil, where the drain plug is and where the filler is a. It will tell you where the dipstick is.
Oil Filter Change Cadillac SRX 2004 2009 2006 Cadillac SRX 3 6L V6
This is a good, clear video.

Mar 04, 2015 | 2006 Cadillac SRX

1 Answer

2004 Cadillac srx key stuck in ignition and loss of power


if the battery is dead then the key will not come out hook up a another car with jumper cables then it will come out

Aug 26, 2012 | 2004 Cadillac SRX

2 Answers

Where is the starter located on a 2005 cadillac srx v 8?


If your SRX has a Northstar V/8 engine the starter is under the intake manifold. The manifold has to be removed to access the starter. Hope this helps, thank you

Sep 04, 2010 | 2005 Cadillac SRX

3 Answers

How to tell if water pump for 04 cadillac srx needs to be replaced.


Your car will overheat very fast and you may either notice coolant leaking from the location of the pump and also possibly a squealing noise due to a bad bearing. Overheating can also be caused by a bad thermostat.

Feb 17, 2010 | 2004 Cadillac SRX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...