Question about Cars & Trucks

Open Question

Ford transit connect torque setting front cv nut

What is the torque preasure for a transit connect van, front cv nut.

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

  • 209 Answers

SOURCE: torque setting for front driveshaft nut


Posted on Apr 15, 2009

  • 324 Answers

SOURCE: changed the gear box on the ford transit van

did you reset the computer after replacing it?

remove the positive battery cable for 10 mins.....

Posted on Nov 26, 2008

  • 45 Answers

SOURCE: need torque setting for front hub nut on a mark 3 golf vr6

195 ft-lbs I verified this in the Volkswagen repair manual aka the vdubbers bible

Posted on Mar 24, 2009

  • 9 Answers

SOURCE: how to change the brake pads in the 2006 ford transit van?

go to a garage tight wad

Posted on Apr 10, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to acces the 4 nuts on a ford transit starter motor as u tube suggest cuting a hole in the body of my van ,are there special tools to do it

which mark version /model /year transit van do you have

most starter motors for the ford transit diesel or petrol
show pictures as only two bolts to hold them on
between exhaust and motor/gearbox housing

Ford Transit Starter Motor Starter Motor For Sale New and Used

this one with three bolts may be a bit of a problem



Dec 06, 2016 | Ford Cars & Trucks

1 Answer

How to replace 2006 ford escape left front axle shaft

How to Replace a CV Axle on a Ford Escape / Mazda ...

? 9:41
Aug 29, 2013 - Uploaded by klowny1969
Axle nut should be torqued to the ford escape its around 205-220 lbs ft How To Change An Axle On A Front Wheel Drive Car ! SUBSCRIBE ! ... How to Replace a Front Axle Half Shaft - Duration: 14:37. ... Alternator replacement 2005 2006 Ford Escape 3.0L DOHC All Wheel Drive - Duration: 13:15.

Front axle replacement Ford Escape 2003 Right front CV ...

? 8:46
Mar 29, 2014 - Uploaded by Fixing cars and stuff
Front axle replacement Ford Escape 2003 Right front CV axle install remove replace This Channel provides ...

Feb 03, 2016 | Ford Cars & Trucks

1 Answer

What size axle nut for 2000ford taurus se

Axle nut size? - Taurus Car Club of America : Ford Taurus Forum > ... > Suspension, Handling and Brakes
Jul 23, 2011 - 8 posts - ‎5 authors 1996 Mercury Sable front axle nut. I have read that the size is 30mm but the socket that I rented (30mm in a ... 2000 Duratec SE White Wagon Axle nut torque question. - Taurus Car Club of America ...
11 posts
May 4, 2012
CV Axle nut size
11 posts
Dec 9, 2011
Why Does The Axle Nut Need Such A Big Torque
11 posts
Dec 7, 2009
2000 Ford Taurus Front Wheel Bearing And Half-axle ...
11 posts
Apr 18, 2009
More results from

Sep 28, 2015 | Cars & Trucks

1 Answer

I need the axle nut torque specifications

Google Make, Model, year CV Axel nut torque. The spec you cite, is not right, that is the troque of the engine at that speed!

Mar 04, 2015 | Cars & Trucks

1 Answer

Front left spindle removal/installation on a 1998 ford explorer 4X2

is it independent suspension up front cv axles or halfshafts is how you tell i cant remeber on the 98 without looking it up but the best way is to get the chiltons so you have your torque spets to reinstall its not to dificult to do eather way but are you trying to replace the stearing nuckle or the wheel bearings? it eather has cv axles that go through a sealed one piece wheal bearings or it has a splined axle with u joints that go through a bearing hub on the rotertif thats the case the spindle has 6 nuts take them off you can get the special tool a sliding hammer to take it off i just use a dead blow if all else fails wont damage it make sure you check the inner neadle bearing for play. grease bolt back up torque down pack your bearings put in the new bearing seal. now you torqu the berings down with the nut to seat the bearings go back 1/4 of a tern you want 8 to 10 thousanhts of preload you can use a dial indicator to check yourself,set the locking washer and set the locking nut to torque remember when you do that your going to loose some of your preload about 1 to 2 thousenths

Jul 22, 2012 | Ford Explorer Cars & Trucks

1 Answer

What are the torque setting for the front discs on a 2003 ford transit

if your doing wheel bearings and youve never done this before,id take it to a mechanic ,there are no torque settings its about experience

Feb 03, 2012 | Ford Transit Connect Cars & Trucks

1 Answer

What is the torque seting for the rear suspension U bolts on a 1996 Ford Transit, plus the torque setings for the wheel nuts for same moter

Tighten the U-bolt nuts evenly in a cross-type pattern with the weight of the vehicle on it's wheels (not jacked up it means)
Tighten the U-bolts nuts to 125 Nm (92 lb-ft).
Wheel nuts
200 Newton meters

Jun 21, 2011 | Ford Transit Connect Cars & Trucks

1 Answer

Wat is the talk settings for transit rear axel

I don't quite know what you want (never heard of talk settings) but if it is the nut that holds the hub on the torque is 251 ft lbs

Mar 30, 2011 | 2010 Ford Transit Connect

1 Answer

I have a 99 mazda protege, 1.6l engine, automatic transmission. I am changing the CV joints out and I need the torque specification for the axle spindle nut that connects the cv joint to the wheel hub.

hi the torque settings for the hub nuts are 236-318 Nm these are the drive shaft nuts that fit on the end of the shaft on the wheel hub hope that's what you required please rate and vote thanks

Sep 20, 2010 | Mazda Protege Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,042 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14445 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides