Question about Cars & Trucks

Open Question

Trans limp mode commodore 2004 vz

Engine fault light and trans warning trans appears to be slipping or stuck in lower gear

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 412 Answers

SOURCE: 2007 Jeep liberty auto trans will not shift from 2nd

YOU NEED TO HAVE TRANSMISSION CONTROL SYSTEM SCANNED..IT HAS DETECTED A PROBLEM IN THE ELECTRICAL SYSTEM,INTERNAL OF TRANS OR A SENSOR FOR TRANSMISSION..A TRANSMISSION IS AN EXPENSIVE COMPONENT..YOU SHOULD GET IT CHECKED ASAP..ESPECIALLY IF YOU HAVE NO WARRANTY LEFT

Posted on Jul 07, 2009

Ad
  • 14036 Answers

SOURCE: poor running

CAMSHAFT POSITION SENSOR IS LOCATED BANK 1 ON BACK TOP ENGINE HEAD. YOU ALSO ANOTHER CAMSHAFT POSITION SENSOR ON BANK 2 ON TOP FRONT OF ENGINE.YOUR PURGE SOLENOID VALVE IS ON BANK 2 ON TOP ENGINE HEAD CLOSE TO CMP SENSOR ON BANK 2 ALSO.

Posted on Sep 19, 2009

  • 82 Answers

SOURCE: 2004 santa fe hyundai

it is probably going into a fail safe mode, get it to a dealer and have it scanned for dtc's

Posted on Apr 30, 2010

  • 63 Answers

SOURCE: my trans is stuck in second gear. Is that what

The town and country vans are know for transmission problems and it would not be stuck in 2nd gear if it was in limp mode. Limp mode typically controls the engine. I have seen people do a transmission flush/filter and add lucas to temporary fix the problem. There is also a good chance that the transmission has a solenoid problem preventing it from shifting into any other gears but second. Hope this helps!

Posted on Jul 30, 2010

  • 163 Answers

SOURCE: The transmission appears to be stuck in "limp-in"

The Transmission Relay is in the Power Distribution Box. It's one of the 3 smaller identical relays underneath the row of 7 larger identical relays. It's the top one immediately below the larger relays. Between the Park Lamp(Larger Relay) & Fuel Pump (Smaller Relay).

Fuse #14 is also for the Transmission Relay.

Posted on Jan 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check transmission trian on Vx commodore executive it had no fluid have filled it but keep getting that message is their a reset button


try this just commodores forum
on the VZ 2004-- 2006
Forum VZ Holden Commodore 2004 2006

I only know of engine service message
clearance using the mode buttons on a VT.VX

i hope you are a lucky person because
any commodore transmission man or auto
driven without fluid would have taken some internal damage






26223843-clxv5ap2upit2hrfgpiip3cn-3-0.jpg

Jun 23, 2016 | Cars & Trucks

2 Answers

My dodge caravan 3.3L shows 5 malfunction codes what do they mean po455 po846 po500 po700 po732


P0455 = Evap leak monitor large leak detected.
This code usually means the gas cap may have been loose or needs the rubber gasket.

P0500 = No vehicle speed sensor signal.
Vehicle speed sensor is located on the transmission near one of the axle shafts (it may need replacing).

P0700 = EATX controller DTC present.
This simply means you have transmission related codes.

P0732 = Gear ratio error in 2nd gear.
This code is of some concern, it means the transmission is slipping in 2nd gear. However the trans may be in limp mode due to the speed sensor code (limp mode means the trans starts out in second gear in order to at least get to a mechanic). The first thing I would do is have these codes cleared as there may be absolutely nothing wrong with the transmission (especially if you pull the trans dip stick and the fluid does not have a burnt smell. The vehicle should drive normally after that. If the check engine light comes back, have the codes scanned ASAP (before any other unrelated code sets). Chances are it may be the output speed sensor if this happens (easy fix). Hope this helps

Regards

Oct 26, 2011 | 2002 Dodge Grand Caravan

1 Answer

Changed transmission computer still have code 605 wont shift out of 2nd gear


did you have pinion factor and quick learn performed on the trans module after replacement? if not then the trans won't shift correctly. also is the check engine light on with any engine codes in memory? the engine module may the trans stuck in limp-in mode(2nd gear).

Aug 10, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Jag xtype 2.0D 2004 Glow plug light flashing.Engine malfunction light on .No loss of power.Hhappened just after refuelling


jaguar x-type 2ltr diesel 2004 the glow plug warning light flashing, was told dirty fuel on fault code all fuel changed and filters. No problems for 20 miles untill engine was put under power on high revs went into limp mode, warning light glow plug falshing again? any ideas thanks.

Feb 09, 2011 | 2004 Jaguar X-Type

1 Answer

My trans is stuck in second gear. Is that what


The town and country vans are know for transmission problems and it would not be stuck in 2nd gear if it was in limp mode. Limp mode typically controls the engine. I have seen people do a transmission flush/filter and add lucas to temporary fix the problem. There is also a good chance that the transmission has a solenoid problem preventing it from shifting into any other gears but second. Hope this helps!

Jul 30, 2010 | 2002 Chrysler Town & Country

2 Answers

2001 Dodge grand caravan sport. Transmission slipping/ jerking. Seems to run only in second gear... still slips and jerks. Smells of burnt trans fluid and the level is low on the dipstick.


I need a little mor info. But the reason for the being stuck in 2nd gear is because when something goes wrong with the tranny. it goes into "LIMP" mode wich keeps the trans. from shifting out of 2nd when you are going forward. It does sound like your trans. is gone out though.

Dec 19, 2009 | 2001 Dodge Grand Caravan

1 Answer

I have a 2000 Dodge Grand Caravan. Lastnight my


Darrell, The trans went into limp mode. 41te trans do funny things. The limp setting is so you can get home or to the dealer. As for the slipping , check fluid first. If ok scan for codes from trans...

Oct 07, 2009 | 2000 Dodge Caravan

1 Answer

2004 Nissan Maxima Intermittent Transmission Problem?


I don't know exactly how the nissans work with their "limp" mode for what gear it goes into and such. This sounds like the computer is sensing a problem and going into the "limp" mode. Go get the code pulled to see what is says. If it has anything saying trans slipping or ratio problem then something internal in the the trans is wrong. Also, check the trans fluid and see if its burnt ( dark brown or black).

Jul 22, 2009 | 2004 Nissan Maxima

2 Answers

1997 isuzu wizard mu check light


Code 24 is a vehicle speed signal sensor fault, the sensor most likely does not provide a useable signal until about 25 MPH, when the computer doesn't see any signal after that speed it turns on the light. Make sense?

Sep 08, 2008 | 1997 Isuzu Oasis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...