Question about 1992 Plymouth Laser

Open Question

Hard to replace ignition coil 92 plymouth laser 2.0 turbo. Does intake have to be removed?

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 99 Answers

SOURCE: low oil pressure light comes on and engine

I am sorry, but it sounds like your oil pump has gone out or is going out. I am sure that you have checked the oil and added it until it is full. If you would like to try to save the engine, you will need to take off the oil pan and change out the oil pump.

Posted on Jul 30, 2009

Ad
  • 3640 Answers

SOURCE: no 12 volts to ignition coil

on a lot of plymouth acclaims ,there is no fuse marked ignition. what I would do is check for voltage at the ignition switch. if no voltage is going thru it. then the ignition switch is bad. check the wires from switch, and turn key to accy,then check wire. then turn to run and record voltage.

Posted on Apr 04, 2010

Testimonial: "Thank you sincerely !"

  • 1757 Answers

SOURCE: firing order for 92 plymouth laser

For the 1992 Plymouth Laser:
I do not know if you have the 1.8L SOHC or 2.0L DOHC (or Turbo) In-Line 4-Cylinder Engine; however I have included both below.

For the 1.8L SOHC In-Line 4-Cylinder:
Firing Order:
1-3-4-2
Cylinders:
..........(back)...........
|...1....2....3....4...|
.........(front)
Distributor:
.....(back)
..(+)
..............1
2
.................3
...4
..............(+)
.....(front)

For the 2.0L DOHC (AND TURBO) In-Line 4-Cylinder
Firing Order:
1-3-4-2
Cylinders:
...........(back)..........
|...1....2....3....4...|
..........(front)
Ignition Connections:
(back)
...3
...2
...1
...4
(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Posted on May 07, 2010

Testimonial: "Thanks for everything this site rocks super fast responses and on the mark advice.(pardon the pun)"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the ignition module on a 99 plymouth voyager


Also called Ignition Coil, is located at the back of the intake manifold...

2_11_2012_12_07_40_pm.jpg

Fig.: remove the 2 lower ignition coil mounting bracket bolts...


2_11_2012_12_08_55_pm.jpg

Fig.: then remove the ignition coil and mounting bracket together from the engine.

Disengage the wiring harness connector from the ignition coil.
Disconnect the ignition wire from the coil.
Remove the coil mounting bracket bolts, then remove the coil and mounting bracket assembly from the vehicle.
The ignition coil can be separated from the mounting bracket.

To install:

If separated, loosely mount the ignition coil to the mounting bracket.
Loosely install the coil and mounting bracket assembly to the intake manifold. Tighten the coil mounting bracket-to-intake manifold bolts to 115 inch lbs. (13 Nm) and the ignition coil-to-mounting bracket fasteners to 96 inch lbs. (10 Nm).
Connect the ignition wire to the coil.
Engage the wiring harness connector to the ignition coil.
If removed, install the windshield wiper/motor module assembly.
Connect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 10, 2012 | Cars & Trucks

1 Answer

Where is the ignition module in a 99 voyager


Hi Eric:
Also called Ignition Coil, is located at the back of the intake manifold...

2_11_2012_12_07_40_pm.jpg

Fig.: remove the 2 lower ignition coil mounting bracket bolts...


2_11_2012_12_08_55_pm.jpg

Fig.: then remove the ignition coil and mounting bracket together from the engine.

Disengage the wiring harness connector from the ignition coil.
Disconnect the ignition wire from the coil.
Remove the coil mounting bracket bolts, then remove the coil and mounting bracket assembly from the vehicle.
The ignition coil can be separated from the mounting bracket.

To install:

If separated, loosely mount the ignition coil to the mounting bracket.
Loosely install the coil and mounting bracket assembly to the intake manifold. Tighten the coil mounting bracket-to-intake manifold bolts to 115 inch lbs. (13 Nm) and the ignition coil-to-mounting bracket fasteners to 96 inch lbs. (10 Nm).
Connect the ignition wire to the coil.
Engage the wiring harness connector to the ignition coil.
If removed, install the windshield wiper/motor module assembly.
Connect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 10, 2012 | Plymouth Cars & Trucks

1 Answer

Where would the pvc value be on a 300 chrysler 2006? also where would the spark plugs be located?


Positive Crankcase Ventilation (PVC) Valve Removal & Installation 5.7L Engine To Remove:
    1.The PCV valve is mounted into the top/right side of the intake manifold.

    2.The PCV valve is sealed to the intake manifold with two O-rings.

    3.Free the PCV valve by rotating counter-clockwise 90 degrees until the locating tabs align with the openings on the manifold.

    4.Remove the PCV valve by pulling straight up from intake manifold and clearing the tabs.

    5.Check the condition of two valve O-rings.
To Install:
  1. Clean the PCV valve opening on the intake manifold.
  2. Inspect the PCV valve O-rings. Replace if suspect.
  3. Apply engine oil to the two O-rings.
  4. Place the PCV valve into intake manifold.
  5. Rotate the valve 90 degrees clockwise for installation.
6.1L Engine To Remove:
  1. The PCV valve is threaded into the right-front corner of the intake manifold.
  2. Remove the rubber hose from the PCV valve.
  3. Unscrew the PCV valve from the intake manifold.
To Install:
  1. Clean the PCV valve opening on the intake manifold.
  2. Check the condition of the PCV valve O-ring. Replace if suspect.
  3. Check the condition of the PCV valve threads and clean if necessary.
  4. Apply engine oil to the O-ring.
  5. Install the PCV valve into intake manifold.
  6. Install the rubber hose to the PCV valve.
prev.gif next.gif
The spark plugs should lead to the coil pack via a spark plug wire but may be hidden by a plastic cover.

The following details the ignition coil changing on the Chrysler 300:

2.7L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Use compressed air to clear the area around the ignition coil and spark plug.
  4. Disconnect the electrical connector from the ignition coil.
  5. Remove the two fasteners securing the ignition coil.
  6. Remove the ignition coil.
To Install:
  1. Install the ignition coil.
  2. Tighten the fasteners to 55 in-lb (6.2 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Install the intake manifold.
  5. Connect the negative battery cable.
3.5L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Use compressed air to clear the area around the ignition coil and spark plug.
  4. Disconnect the electrical connector from the ignition coil. NOTE: Loosen the ignition coil fasteners by alternating back and forth. Do not lose the spacers under the coil when loosening the fasteners.
  5. Remove the two fasteners securing the ignition coil.
  6. Remove the ignition coil.
To Install:
NOTE: Tighten the ignition coil fasteners by alternating back and forth. Do not lose the spacers under the coil when installing the coil.
  1. Install the ignition coil.
  2. Tighten the fasteners to 60 in-lb (6.7 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Install the intake manifold.
  5. Connect the negative battery cable.
5.7L Engine (2005) To Remove:
NOTE: Carefully note the position of each spark plug cable before disconnecting them so they can be installed in their original positions to prevent misfire.
NOTE: The throttle body intake air duct or intake air box may need to be removed to gain access to certain ignition coils.
  1. Disconnect the electrical connector from the ignition coil.
  2. Remove the secondary ignition cable from the coil.
  3. Use compressed air to clear the area around the ignition coil.
  4. Remove the two fasteners securing the ignition coil. Bolts are retained to coil.
  5. Remove the ignition coil. Pull with a slight twisting motion to help release the boot seal with the spark plugs.
To Install:
NOTE: Apply a light film of dielectric grease to the inside of the coil boots before installation.
  1. Clean area around spark plug and coil mounting area with compressed air.
  2. Install the ignition coil.
  3. Tighten the fasteners to 105 in-lb (12 Nm).
  4. Connect the electrical connector to the ignition coil.
  5. Connect the secondary ignition cable to the coil.
  6. Install the air duct or air box if removed.
Ignition coil mounting bolts (5.7L & 6.1L engines) chry-02-57-263.gif

5.7L (2006) & 6.1L Engine To Remove:
NOTE: Each ignition coil, mounted on the valve cover, fires two spark plugs at each cylinder.
  1. Disconnect the negative battery cable.
  2. Use compressed air to clear the area around the ignition coil and spark plug.
  3. Disconnect the electrical connector from the ignition coil.
  4. Remove the two fasteners securing the ignition coil.
  5. Remove the ignition coil. Pull with a slight twisting motion to help release the boot seal with the spark plugs.
To Install:
NOTE: Apply a light film of dielectric grease to the inside of the coil boots before installation.
  1. Install the ignition coil.
  2. Tighten the fasteners to 105 in-lb (12 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Connect the negative battery cable.
prev.gif next.gif

Sep 24, 2010 | 2005 Chrysler 300

1 Answer

It's a 92 Plymouth laser 1.8 none turbo, wont start when cold..will only idle. Once it gets some heat in it, it runs and starts fine. It threw 3 codes, volume Air Flow senor, intake air temperature sensor,...


Hello! system dropped our chat... probe onto the Gray/White and - probe on the Gray/black...Meter set to read 5 volts...start engine...Meter must read less than 1 volt (.85)...Slowly increase throttle...Meter must read 4 volts at full throttle...Voltage must increase smoothly...If it jumps, jerks or acts erratic the TPS is defective....saailer

Sep 15, 2010 | 1992 Plymouth Laser

1 Answer

92 plymouth laser rs turbo when i come off clutch in first gear car shakes or stutters problem comin out of first


Your driving a '94 laser... thats definately a large portion of your problem. I would take it to a salvage yard, part it out, or sell it for scrap. Then take that money, invest in a huffy bicycle and the only problems you should ever encounter is the tires going flat or the seat being a pain in your rear parts.

Aug 21, 2010 | 1994 Plymouth Laser

1 Answer

Firing order for 92 plymouth laser


For the 1992 Plymouth Laser:
I do not know if you have the 1.8L SOHC or 2.0L DOHC (or Turbo) In-Line 4-Cylinder Engine; however I have included both below.

For the 1.8L SOHC In-Line 4-Cylinder:
Firing Order:
1-3-4-2
Cylinders:
..........(back)...........
|...1....2....3....4...|
.........(front)
Distributor:
.....(back)
..(+)
..............1
2
.................3
...4
..............(+)
.....(front)

For the 2.0L DOHC (AND TURBO) In-Line 4-Cylinder
Firing Order:
1-3-4-2
Cylinders:
...........(back)..........
|...1....2....3....4...|
..........(front)
Ignition Connections:
(back)
...3
...2
...1
...4
(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

May 07, 2010 | 1992 Plymouth Laser

1 Answer

Car has intermittent miss


It is 1/2 hard

3 or 4 are going to be under the intake manifold, 3or 4 (depending on your engine of course) are going to be on the other side.

Obviously the 3 or 4 under the manifold are going to be difficult, remove the intake, replace gaskets, etc..

Jan 28, 2010 | 2002 Lincoln LS

1 Answer

Trying to make my car go fast


yes you can, The turbo has no clue if the trans is auto or manual. Good luck, God bless

Oct 01, 2009 | 1990 Plymouth Laser

Not finding what you are looking for?
1992 Plymouth Laser Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...