Question about 2004 Ford E150

Open Question

2002 Ford Conversion van rear seat won't ley down flat

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: 2002 Ford Explorer, rear driver side door

Wil it work at the door switch or not at either switch? If not make sure you have power and ground to the motor in up and down positions. if so suspect the motor.Also the cable operated regulators break and will not let the window go up or down

Posted on Jul 30, 2009

  • 1 Answer

SOURCE: 1993 ford e-150 conversion van heat and a/c

Selection lever does not move to AC vent or floor vent only to the defrost. AC compressor does not kick in when AC is selected.
Vacuum level is at 18 instead of 23.
Any suggestions.

Posted on Aug 02, 2010

  • 1 Answer

SOURCE: I have a 2003 Ford

I just encountered this problem with my 2000 Ford Excursion. After fighting with it for several hours I realized that the section of the seat that is facing up towards the roof of the vehicle was applying pressure to the back of the seat that was facing down and preventing the back of the seat from coming up when I pulled the lever. So, the next time I pushed the seat up that is facing the roof while I pulled the lever and this resovled my problem.

Posted on Sep 08, 2010

caroldon
  • 17129 Answers

SOURCE: 2002 ford windstar van- left front door window

Might have to open and see if the powerr comes to the unit. If not there can be a break inthe door hinges section where the main power comes in.
If power is present but not the control, it can be failure of the switch control, failure of the logic control IC, failure of the motor.

Posted on Sep 24, 2010

  • 8 Answers

SOURCE: 2006 Ford Explorer: Back seat won't fold flat to

Okay so im just going to start from the seat being upright in a normal riding position.

1. You need to fold the head rests first. Pull the black tab under both headrests. They should spring into a folded position.

2. pull the side seat lever (on the door side of the seat). This will fold the top/back support down to an angle.

3. There is one more lever on the backside of this seat. Its in plain sight on the angled portion of your seat. Lift the big plastic lever.

4. While keeping the handle lifted, grasp the back of the seat and pull it torwards the front of the car. The seat should come unlocked and roll forward and down more towards the floor. If you have a bunch of junk on the floor, it obviously wont work. clear the path and the seat will fold completely flat.

Also, your drivers seat and front passenger seat cannot be all the way back, they need to come forward some in order for the second row seats' head rests to clear and fold flat.

Posted on Oct 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the back seat from a 1994 chevy g20 van?


I believe the seats are bolted to the floor of the van. Make sure you unplug all electrical connections before removing the seats.

Feb 11, 2014 | 1994 Chevrolet G20

2 Answers

2002 Ford Thunderbird turns over but won't start


Check for fuel at engine and for spark at coil

Nov 26, 2012 | 2002 Ford Thunderbird

1 Answer

We have a 199 Chevy conversion van that has a full bench seat in the very back with a rear facing seat and we can't figure out how to lay the seat down now that we need to. The switch will click when...


I have the same problem. found out you like i have a power fold down seat. there should be a small motor mounted underneath the rear seat. attached to it are two cables. those cables are what move the seat up and down. check to see if the cables are broken or snapped apart. then check all the seat levers support bars to find out if any of them are bent or misaligned. that can cause your cables to break.

Aug 06, 2011 | 1995 Chevrolet G20

2 Answers

Was there a recall on the windstar van 2002


Welcome to FIxYa.com




Yes there isleedavidian_217.jpg

Fuel related- speed sensor and Seat to latch recall



Thank you for using FixYa.com

Regards, Lee Davidian

Jan 02, 2011 | Ford Windstar Cars & Trucks

1 Answer

Where is the fuse box on this van. It is a conversion van.


What type of conversion? if the front of the van remains Ford the fuse box is located under a dash trim panel to the left of the steering wheel, in front of your knee, there are two plastic quick releases under the panel, twist them counter clockwise to remove and pull down

Nov 17, 2010 | 1993 Ford Econoline

1 Answer

!990 Dodge Grand Caravan Rear Seat


If yours is a Braun Entervan conversion and the spare tire has been relocated to the inside rear behind the seat, your rear seats will not come out, they are bolted to the floor. From the factory, they are designed to unlatch and come out, but after the conversion, the undercarriage of your van is completely different, especially if you have a lowered floor, and even more so if you have a kneeling van. If you unbolt the rear seats, you will have to bolt them back in, they're not quick releae anymore. If you van floor is lowered (usually about 10") "High Water" has a whole new meaning for you, it doesn't have to be very high at all to flood your interior.
Good Luck,
Steve, Houston TX

Jan 05, 2009 | 1994 Dodge Grand Caravan

2 Answers

Electronic Control Module Installation 1994 G20 Chevy Van


I just had the same problem. If it is a regular van try under the driver seat in a plastic box. If it is a conversion van try in a pannel just behind driver seat on side of van wall behind a pannel that looks like a vent.

Dec 28, 2008 | 1987 Chevrolet G20

1 Answer

How do you lay down rear seat flat?


I just bought a 93 GMC Safari Van and couldn't figure this out either. Luckily, I did have the manual. It appears that the  lever under the front of the sofa moves in forwards and backwards. There is a lever on the corner of each side. Lift up on each and pull cushion forward. Also, you can push on the back of the sofa to help it go down. Hope this helps! 

Oct 15, 2008 | 1998 GMC Safari

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...