Question about 2004 Chrysler Pacifica

1 Answer

My 05 Pacifica went into "limp in" mode which means it is stuck in 2nd gear. I took it to AutoZone and put it on the code machine. It pulled up P0700, P0715, P0731 and P0733. I changed out hte Speed Sensor Input and Output and still have the same problems but now it only pulls codes P0700 and P0731. Anyone have any ideas? The speedometer and Tachometer all worked before and after the speed sensor change.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 21,873 Answers

Well code 700 is a generic code that means there is a problem with the transmission or the control module. Code 731 is for a problem with first gear which would explain why it stays in second gear.
Someone will need to check the circuits involved with first gear and the trans control module. A shop manual will be necessary to get the testing procedures.

Posted on Jul 30, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
partyd
  • 141 Answers

SOURCE: My van is not shifting

734 is "Gear 4 Ratio Incorrect

the acumulator inside the tranny is bad

Posted on Nov 23, 2010

  • 1 Answer

SOURCE: 2002 chrysler town and country wont leave limp mode

try getting a new shift solenoid for it. i had the same problem on my 2002 chrysler town and country and my plymouth breeze which is also a dodge product. it is very simple to do and doesnt take all that long. the part will probably run you about 150 to 200 dollars but it should fix your problem.

Posted on Apr 04, 2009

  • 396 Answers

SOURCE: 2000 300m shifts into 2nd

you replaced the output speed sensor, try replacing the input speed sensor, sometimes called the turbine speed sensor, thats where the computer gets the info to shift.

Posted on Nov 27, 2010

Testimonial: "Thank you!!!!! Thank you!!!! IT was the right answer. May Karma be with you x10. Happy Holidays."

  • 144 Answers

SOURCE: I have a P0700 Code

the transmission soleniod assembly is bad need to replace it

Posted on May 28, 2011

nicole99wu
  • 1049 Answers

SOURCE: 2002 pt cruiser code p0733,

this obd2 trouble code table can help you understand the meaning of code.

Posted on Sep 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What might cause 2004 4l80e to be in limp mode no speedometer and stuck in 2nd gear


When the system goes into to Limp Home mode it means that a serious fault has occurred in the electronics or a mechanical failure has been sensed. What you need to do now is have the computer control system scanned for fault codes, this (the fault codes) will give you a starting point to diagnose the problem that has caused the Limp Home mode to be initiated by the computer control module.

Dec 20, 2016 | Cars & Trucks

1 Answer

05 chrysler pacifica 0700 warning code and shifting problems


This is classic limp in mode. The computer won't let it shift to prevent further damage to the transmission. Gas mileage will go down because you're stuck in low gear. P0700 is a pretty general code. You need to get it to a shop for a diagnosis

Aug 25, 2017 | 2005 Chrysler Pacifica Limited

2 Answers

My dodge caravan 3.3L shows 5 malfunction codes what do they mean po455 po846 po500 po700 po732


P0455 = Evap leak monitor large leak detected.
This code usually means the gas cap may have been loose or needs the rubber gasket.

P0500 = No vehicle speed sensor signal.
Vehicle speed sensor is located on the transmission near one of the axle shafts (it may need replacing).

P0700 = EATX controller DTC present.
This simply means you have transmission related codes.

P0732 = Gear ratio error in 2nd gear.
This code is of some concern, it means the transmission is slipping in 2nd gear. However the trans may be in limp mode due to the speed sensor code (limp mode means the trans starts out in second gear in order to at least get to a mechanic). The first thing I would do is have these codes cleared as there may be absolutely nothing wrong with the transmission (especially if you pull the trans dip stick and the fluid does not have a burnt smell. The vehicle should drive normally after that. If the check engine light comes back, have the codes scanned ASAP (before any other unrelated code sets). Chances are it may be the output speed sensor if this happens (easy fix). Hope this helps

Regards

Oct 26, 2011 | 2002 Dodge Grand Caravan

1 Answer

How do i fix the overdrive ligh flashing on my 1993 geo prizm? it takes off in 2nd gear in drive but will go into 1st when you put it in that gear


The overdrive light is flashing because there is a diagnostic code stored in the Transmission control mudule.You will need to have the codes pulled to know where the problem is.The 2nd gear only condition is not a symptom, it is limp mode caused by the code being stored.There are about 30 different problems that can cause limp mode,so there is no way to guess.There is a procedure to pull codes that I can give you if you want to do it yourself.Just let me know,Thanks!

Mar 25, 2011 | 1993 Geo Prizm

1 Answer

My trans is stuck in second gear. Is that what


The town and country vans are know for transmission problems and it would not be stuck in 2nd gear if it was in limp mode. Limp mode typically controls the engine. I have seen people do a transmission flush/filter and add lucas to temporary fix the problem. There is also a good chance that the transmission has a solenoid problem preventing it from shifting into any other gears but second. Hope this helps!

Jul 30, 2010 | 2002 Chrysler Town & Country

1 Answer

Car wont shift from 2nd gear and speedometer doesnt work. diagnostic code p0700. what does this mean?


the PO700 code is a generic transmission code. You would need access to a proper scan tool to check for transmission codes. However if you speedo isnt working, it sounds as though you have a bad output speed sensor. This part runs about 60.00 from the dealer, and is fairly easy to install. No speed signal will put the transmission into limp mode, and keep it stuck in 2nd gear.

Nov 17, 2009 | 2000 Chrysler 300M

1 Answer

I have a 2000 Dodge Grand Caravan. Lastnight my


Darrell, The trans went into limp mode. 41te trans do funny things. The limp setting is so you can get home or to the dealer. As for the slipping , check fluid first. If ok scan for codes from trans...

Oct 07, 2009 | 2000 Dodge Caravan

1 Answer

I have a 2001 town and country. yesterday i went to put it into park and it sounded like a clunk. Like it shifted really hard and now my transmission is stuck in 2nd gear. I took the negative batterey...


This is called the limp mode. It means that you have a transmission problem. It goes into limp mode to protect the transmission from total failure. You need to take it to a transmission shop to perform a diagnosic test to see if it needs repair or replace

Jul 11, 2009 | 2009 Chrysler Town and Country

1 Answer

Replaced trans, now car is stuck in limp in mode


MCARTER859: check the connections where the transmission harness and engine room harness come together. Unplug them and reconnect them I have run into more than one case with the same symptoms as yours which ended up being nothing more than poor connections.
CROSS YOUR FINGERS1

Apr 21, 2009 | 2003 Mitsubishi Eclipse Spyder

2 Answers

In limp mode cant get out 96 dodge avenger ES V6


unhook the battery for about 15 minutes and hook it back up... that should reset it

Jan 23, 2009 | 1998 Dodge Avenger

Not finding what you are looking for?
2004 Chrysler Pacifica Logo

1,283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...