Question about Cars & Trucks

Open Question

Tecalemit de7184 roller brake tester instruction manual

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the code p1589 with fcar scanner


MULTI-MODE MANUAL TRANSAXLE SYSTEM ADJUSTMENT
1. USING INTELLIGENT TESTER: CLAMP POSITIONADJUSTMENT (CLUTCH POSITIONADJUSTMENT)
Tech Tips
The multi-mode manual transmission system has a load controlled clutch cover (adjustment system). The pressure plate moves depending on the wear
condition of the clutch disc lining.
When removing or installing any parts related to the multi-mode manual transmission system, move the clutch actuator to the clutch clamp position. This is
for normal operation of the load controlled clutch cover (adjustment system).
If the clutch position adjustment operation input fails, perform the operation again from step (a) more than 15 seconds after turning the ignition switch off.
Note
Do not depress the brake pedal while performing the clamp position adjustment using an intelligent tester.
a. Prepare the vehicle:
Stop the vehicle.
Shift the lever into the N position.
Turn the ignition switch off.
Apply the parking brake.
b. Connect the intelligent tester to the DLC3.c. Turn the ignition switch on (IG).
d. Turn the intelligent tester ON.
e. Select the following menu items: Powertrain / Multi-Mode M/T / Utility / Parts Exchange.
f. Read the information.
g. Press the Next key.
h. Read the information.i. After checking the vehicle condition, press the Next key.
j. Read the information.
k. Press the Next key.
l. Read the information.m. Press the Next key.
n. On the Multi-Mode M/T / Utility screen, select Step 1 Clutch Position Adjustment (Clamp Position Adjustment).
o. Press the Next key.
p. Read the information.q. Press the Next key.
r. Complete Clutch Position Adjustment.
s. Turn the intelligent tester OFF.
t. Turn the ignition switch off.
u. Replace the malfunctioning parts.
Tech Tips
Perform [Initialization and Learning] after repairing the multi-mode manual transmission control system .
2. WITHOUT USING INTELLIGENT TESTER: CLAMP POSITIONADJUSTMENT (CLUTCH POSITIONADJUSTMENT)
Tech Tips
The multi-mode manual transmission system has a load controlled clutch cover (adjustment system). The pressure plate moves depending on the wear
condition of the clutch disc lining.
When removing or installing any parts related to the multi-mode manual transmission system, move the clutch actuator to the clutch clamp position. This is
for normal operation of the load controlled clutch cover (adjustment system).
If the clutch position adjustment operation input fails, perform the operation again from step (a) more than 15 seconds after turning the ignition switch off.a. Prepare the vehicle.
Stop the vehicle.
Shift the lever into the N position.
Turn the ignition switch off.
Apply the parking brake.
b. Using SST, connect terminals TC and CG of the DLC3
SST
09843-18040
c. Turn the ignition switch on (IG) with the brake pedal released.
d. Depress the brake pedal 7 times or more within 3 seconds.i. The buzzer sounds twice with an interval of 0.25 seconds.
e. Depress the brake pedal.
f. Shift the shift lever in the following sequence with the brake pedal depressed: N?E?M?+?M?+?M?+?M?+?M?E?N.
g. Release the brake pedal.
h. Depress the brake pedal again.i. The buzzer sounds at intervals of 0.5 seconds as follows (an interval of 2.5 seconds exists between each cycle).
Once when adjusting the clutch clamp position (one cycle)
Tech Tips
If the buzzer does not sound at this time, wait at least 15 seconds after turning the ignition switch off. Then, perform the procedure from step
(a) again.
i. Depress the brake pedal 3 times or more within 2 seconds.
i. The buzzer sounds twice with an interval of 0.25 seconds.
j. Depress the brake pedal.
k. Shift the shift lever to the [-] position with the brake pedal depressed.
l. Release the brake pedal.
m. Complete clutch position adjustment.
n. Turn the ignition switch off and wait at least 10 seconds.
o. Disconnect the SST from terminals TC and CG of the DLC3.
p. Repair the malfunctioning parts.Tech Tips
Perform [Initialization and Learning] after repairing the multi-mode manual transmission control system .

May 22, 2015 | 2009 Toyota Yaris

1 Answer

No power to left rear turn/ brake light


Check the display. Ask a helper to step on the brake pedal while you check the lights from the rear. If no lights appear, check the fuse that connects the brake lights. The owners manual will show the location of the fuse box and which fuse is for the brake lights. Pull out the fuse and look at the wire in the central window. If the wire is broken, replace the fuse. Make sure the new fuse is not blown, and carries the same amperage.
Take note of lights that are out, if any are working. The problem may be cured by replacing the bulb in a brake light that's out. A burned out bulb has a broken filament and a dark brown spot on one side. Check the owners manual for bulb type.
Check the circuit if replacement bulbs and fuses do not restore the lights. Find the wiring diagram in the vehicle assembly manual. The circuit for the brake lights runs from the battery to the fuse, to the pedal switch, to a connection plug, to the lights. The circuit has to be checked with a volt tester at all points.
Check the battery power and the light on your volt tester. Turn the ignition key far enough to activate the electrical systems. Turn on the lights to check for battery power. If the battery has power, ues it to check the volt tester. Put the black lead (the ground) from the volt tester on the negative battery terminal. Briefly touch the red tester light on the positive terminal. The light on the volt tester should flash brightly.
Test the wiring to the fuse. Clip the ground wire to solid metal near the fuse. Touch the light tip to both sides of the fuse. Both should light the tester. If neither side lights, the wire between the battery and fuse is bad. If only one side lights, the fuse is blown.
Test the switch and wiring. Touch the light tip of the tester to both terminals on the brake pedal switch without putting any pressure on the pedal. One should carry power and the other should not. When both show power, the switch is stuck and the brake lights are always on. If neither shows power, the wiring between the fuse and the switch is bad. Now check both switch terminals while the pedal is depressed. Both sides should light the tester. If not, the switch is bad.
Check the connection plug. Unplug the connection and refer to the vehicle manual to identify the brake light wire. Touch the tester light on the brake light wire at the inner socket on the battery side. If the tester lights, the power is flowing to this point. If not, the wire between the plug and the pedal switch is bad.
Check the socket. Plug in the connector plug and remove the bulb. Touch the contact inside the socket. If the tester lights, the socket is good. The socket and wire running to the plug should be replaced if the tester doesn't light.
Check the bulb with the ground wire. The bulb must be in its socket. The ground wire running to the socket should be black or brown. Stab the tester through the insulation. If the tester lights, the bulb is good. Replace the bulb if it doesn't light.
Check the ground wire. Remove some of the insulation around the ground wire. Twist one end of the extra wire around the exposed ground wire. Touch the other end to a solid piece of metal. If the brake light comes on, the ground wire is bad.
Best Offer 2013 11 MB SD Connect Compact C4 Star Diagnosis with WiFi

Oct 13, 2014 | 2000 Ford Expedition

1 Answer

How do I get to the parking brake adjusting nut under the center console of a 2001 honda accord LX


If handbrake has excessive travel and the brake pedal is low then you havent set the rear brakes up properly ,if a drum then you clean the lip on the edge of the drum so it has a bevel then you manually adjust the auto adjuster till the drum just slides over then tap outer edge of drum wth a small hammer to level the shoes and then see if you can then adjust the auto adjuster up a bit more .Also when taking the drum off again make sure that the handbrake mechanism lever is right back ,Now if you adjust the brakes on the handbrake cable then it will be out of square and will not work on a brake roller tester ,and the footbrake will still feel spongey then you get a inspection failure for excessive pedal travel and low handbrake efficiency ,this model of car should be able to lock the rear brakes up at 30mph when jerking the handbrake up hard and it shouldnt have more than 3 clicks when done correctly

Apr 15, 2012 | Honda Cars & Trucks

1 Answer

I need a calibration manual for a BM Autoteknik brake tester BM7010


hi there
are you interested to sell the rig and the weights?cheers

Feb 20, 2012 | Cars & Trucks

1 Answer

Have a 1999 Chev. Suburban. Problem is with brake lights. Top panel (on roof) works but neither side panel works. Replaced circut boards in tail lights, new bulbs, and all fuses are good. What next?


WITH A GOOD FUSE TESTER, TEST ALL THE FUSES FUSEBOX UNDER THE HOOD & INSIDE THE VEHICLE. IF THE FUSES ARE ALL GOOD WITH THE TESTER YOU MUST HAVE A BAD BRAKE LIGHT SWITCH OR A BAD TURN SIGNAL SWITCH. THE BRAKE LIGHT CIRCUIT GOES UP THROUGH THE TURN SIGNAL SWITCH & THEN TO THE BRAKE LIGHTS. FIRST OF ALL IS THE BRAKE LIGHT SWITCH GOOD ? THE ORANGE WIRE FEEDS THE BRAKE LIGHT SWITCH, THE WHITE WIRE PUTS POWER TO THE TURN SIGNAL SWITCH, SO THE LIGHTS CAN BE USED AS TURN LIGHTS OR BRAKE LIGHTS. , PUT A TESTER IN THE WHITE WIRE & PRESS ON THE BRAKE PEDAL. IF THE TEST LIGHT LIGHTS UP, BRAKE LIGHT SWITCH IS GOOD, BY THE WAY THE BRAKE LIGHT FUSE MAY BE LABELED" STOP", THE FUSE LABELED" BRAKE" IS FOR THE ABS SYSTEM. TO CHECK THE TURN SIGNAL SWITCH FOR BRAKE LIGHTS, REMOVE THE PLASTIC COVER FROM UNDER THE STEERING WHEEL, PRESS ON THE BRAKE PEDAL, PUT THE TESTER IN THE SMALL YELLOW WIRE, THEN THE SMALL GREEN WIRE. IF THERE IS NO POWER IN EITHER WIRE, THE TURN SIGNAL SWITCH IS BAD.

Jan 11, 2011 | 1999 Chevrolet Suburban

1 Answer

Rear break ligths not working, fuse is fine


check if bulb is busted if not check pedal brake switch, sometimes socket connectors were detached or loose or use light tester to check manually from the fuse connection down to the wiring circuit until you reach the tail of your car. let somebody do the brake pedal pushing when checking using the light tester. i don't see any reason if your problem is not solve using these technique

Jun 19, 2010 | 2008 Isuzu i-Series

2 Answers

Power wire for brake stop switch? I'm adding an electric brake controll and need to know which wire has power when the brakes are pushed? There's about6 going into switch


to do this you need a twelve volt tester ground one of tester and test the wire on brake switch and u will find the right wire

Jul 07, 2009 | 1999 Jeep Grand Cherokee

2 Answers

No brake lights but 3rd light works all fuses are good


Sounds like a broken wire somewhere.
Since the middle brake light works I would suspect it is somewhere in the trunk or close to the back seat.
Buy or make a tester. A 12v light with a clip on one wire that you clip to a good ground on the car the other wire with a sharp point. Turn the turn signals on then poke wire to rear lights until tester lights. When tester lights you know the break is somewhere inbetween the tester and the brake lights.

Hope this helps.

Stan

Apr 16, 2009 | 1985 Buick Skylark

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...