Question about 2011 Honda Odyssey

1 Answer

Trunk lid mechanical bind when closing from control switch - works OK if pulled down slightly then hit control switch on trunk lid. The bind causes the lid to start down then re-open I see the mechanism twist to the left and bind. Need to get to the motor control mechanism but cannot find a path to get to the mechanics of the motor.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 20,706 Answers

Fsm time.
buy the FSM.
or
alldata.com

Posted on Jan 27, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: hood latch won't release

This has happened to me several times, this will take two people, but all you need to do is have one person pull the hood release, while person number 2 pushes down on the hood, and then pulls up...that ought to do the trick

Posted on Jan 28, 2009

dmsr63
  • 2050 Answers

SOURCE: mechanic says i need new front axles......

Usually once the boot is torn, dirt goes in, and all of the lubricant goes out. If you have been driving it this way, it will damage things faster. Normally you hear a "click" when turning out of a bad cv joint.It is a safer solution to just replace both, but of coarse, not cheaper.

Posted on Aug 19, 2009

Testimonial: "so i should replace both AXLES or both BOOTS? "

  • 4 Answers

SOURCE: License Plate light and tail lights on trunk led not working.

I had the same problem on a 2008 Civic. It turns out it was a poor wiring harness design. The harness was being pinched as the trunk lid opens and closes. In the wire bundle, there is a crimp connector where 3 wires connects to 1 wire. The 1 wire in the crimp came loose. I reconnected everything with a new crimp connector, taped up the wire loom, and everything worked once again.

Posted on Aug 27, 2009

philschneide
  • 448 Answers

SOURCE: replace the blower motor.

Under the glove box:

Disconnect the blower motor power transistor electric connector (the transistor is far over to the left, with a curly wire coming down to it.)

Remove the blower motor power transistor mounting screws the remove the transistor.

Disconnect the electrical connector from the blower motor (slightly to the right of the motor).

Remove the blower motor mounting screws and then remove the blower motor assembly.
(there are, I believe, 3 screws; 1 just below the connector; 1 above the connector, higher up, and slightly to the left; and 1 over to the left of the blower motor)

Remove the circlip from the blower motor shaft to release the fan from the motor.

Installation is reverse.

Hope this helps you deal with it.

Posted on Dec 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble with trunk lid staying closed goes down but comes back up


Please make sure your keys are not in the trunk because there is a safety mechanism that will not allow the trunk to stay closed if the keys are detected in the trunk. The other issue will be if the hold down mechanism is not pulling the trunk completely closed once the trunk engages the lock. You will then have to have it serviced to make sure the pull down motor is operating.

Aug 06, 2011 | 2005 Audi A8

1 Answer

Trunk does not completely close


The trunk latch contains a switch which closes when the trunk lid is pushed closed by hand, then this switch sends power to the trunk lid pull down motor which then finishes closing the trunk lid. Often the switch or motor will go bad and the whole thing will stop working. It takes a little testing to figure out which part is at fault but they are usually quite easy to fix.

Jun 10, 2010 | 1996 Lincoln Town Car

2 Answers

Power decklid won't pull trunk down. Replaced actuator and switch in decklid and the servo in the trunk.. works intermittently


If it works intermittently, you probably have a damaged wire -- my guess would be where the wiring harness goes to the trunk lid. The constant motion of use can damage the wires internally. They still look ok on the outside usually, you'll have to check them electrically (with a meter or test light) The other possibility is damage to the harness that goes to the latch from something moving in the trunk and hitting it. Good luck.

Apr 26, 2010 | 1993 Lincoln Town Car

2 Answers

Trunk doesn't close all the way


Before going to a repair facility, check the fuse for 'convenience group' , the relay in the distribution box under the hood, the connector in the trunk, and the closing motor itself--sometimes they get loose on their brackets, and fall away from the metal closing loop on the trunk lid. Also check the metal closing loop on the trunk lid--sometimes they get loose and don't enter the closing motor mechanism at the right depth for the motor to capture it and secure it down.

Feb 14, 2010 | 1997 Cadillac Seville

1 Answer

1997 Cadillac Deville Concours Trunk will not close!


latch mechanism is probably motorized. Gently pushing the trunk lid down slides the lid/latch bar into the mechanism. this pushes a tab inside the motorized latch and the drive motor pulls the lid down tight and secure. you may be able to test the latch mechanism by sliding a pen or screwdriver into the latch groove to simulate the lid coming down. if you see the motor drive engage, and pull down the tool, you at least know this is working.

Sep 30, 2017 | 1996 Cadillac DeVille

1 Answer

Trunk lid pull down mechanism does not engage


you should replace the trunk pull down mechanisim

Jun 07, 2009 | 1994 Buick Park Avenue

1 Answer

Trunk lid will not pull down


i had the same problem, there is a stop switch that is bad. (got one from a junkyard but it was bad also). haven't found one online yet, but will ask my local ford dealer if part is still available.
so untill i find one, i got the motor to stop at the all the way down position (trunk closed) and then unpluged the motor.

Apr 26, 2009 | 2004 Lincoln Town Car

1 Answer

Automatic trunk lid closing device stopped working.


Get a trunk pull down switch from a dealer. This will fix it.

Apr 18, 2009 | Buick Riviera Cars & Trucks

Not finding what you are looking for?
2011 Honda Odyssey Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...