Question about Cars & Trucks

1 Answer

Vauxhall corsa windscreen wipers not working

Electrics to my front window wipers are working? its a 51 plate 1lt engine.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 12,223 Answers

See the diagram attached, and fix it. God bless you
tight any connector, and clean it. Test the motor for dirty, or faulty and repair or replace.
vauxhall corsa windscreen wipers not working - 63ad7a99-23e0-4fd1-99ea-746a86445db2.jpg53eafb52-cdff-4a33-8dbf-98f45724b7b2.jpg

Posted on Jul 30, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Windscreen wiper not working

check the switch on the steering usualy it becomes faulty after a while and also your window washers could be blocked but try turning it on if you do not hear a buzzing sound the motors needs to be replaced.

Posted on May 21, 2008

GasparMacari
  • 166 Answers

SOURCE: corsa head torque settings?

for 4ee1
cylinder head
stage 1: 40Nm
stage 2: 60° - 75°
stage 3: 60 - 75°
let me know if u need any more of those
take care

Posted on Aug 21, 2009

GasparMacari
  • 166 Answers

SOURCE: Vauxhall Corsa brake pads

lift car
take the wheel off
the caliper off, the screw is right behind the side ur gonna have in front of you,
after u take that screw off the pads will be free to take off,
replace,
check the piston of the caliper and check for the conditions of all the rubber that is on the caliper, replace if needed
screw it back and put the wheel back to its place
hope this helps

Posted on Aug 21, 2009

  • 5 Answers

SOURCE: My front windscreen wipers on my BMW mini are not

i repaired mine in about an hour , the motor contactor will be burnt out , this can be rapaired easily by soldering , the motor can be removed fairly easily without all the uneseccery strip down as many people think , if you would like the strip dwon procedure let me know

Posted on Feb 05, 2010

  • 3 Answers

SOURCE: Windscreen wiper snapped-Peugeot 206 Verve 52 plate

this just happened to us, the drivers side stopped working after getting tangled up with the passenger side...it was just a case of tightening up the 13mm nuts on the wiper arm.

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Citroen relay 2011 i have no wipers windows or mirrors and the battery drains in about 4 days ??? otherwise faultless , any ideas , many thanks


Windscreen wipers not working after jump starting vehicle.

Affected vehicles

  • All models.

Problem

Cause

  • Windscreen wiper motor and engine wiring harness damage caused by jump starting vehicle using incorrect earth point.

Remedy

Parts Earth point warning label
  • Carry out electrical, mechanical and component tests (as applicable) to eliminate any other possible cause(s).
  • If no fault(s) found: Replace windscreen wiper motor and engine wiring harness.
  • Attach earth point warning label Fig.126139.1.

Nov 30, 2016 | Citroen Cars & Trucks

1 Answer

51 plate corsa need to change starter motor, how the hell do you undo the top nut?


normally takes a long extension up and over the top of the starter or one with a u-joint on it for angle changes on most models..try that unless you dont see any real channel for acess..aks the parts store for that particular model.. they will dictate the proceedure forthe car..

Jan 22, 2013 | Vauxhall Cars & Trucks

1 Answer

My windscreen wipers have stopped working on my vauxhall combo


my Vauxhall combo van keeps on blowing the windscreen wipers fuse what can cause this sometime there working for a round ten mins then blow the fuse

Apr 16, 2012 | Cars & Trucks

1 Answer

Window wipers sticking


How to change a wiper motor & repair wiper mechanism on 1998 Audi A4

First time you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows:

1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

May 22, 2011 | 1998 Audi A4

1 Answer

Windscreen wipers not working on my vw passat 2005 '05' but washers are working!


First time you must diagnose why windscreen wipers going slow and/or stopping.
If the windscreen wipers fuse is good:
In order to find out the cause of wipers stopping you can try follows:

1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Apr 14, 2011 | 2005 Volkswagen Passat

1 Answer

My front wipers on A4 audi have been slow eversince windscreen was replace a couple of months ago. Obviously this time of year they have been little used but this morning have little power and stop dead on...


First you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Sep 22, 2010 | Audi A4 Cars & Trucks

1 Answer

Wiper motor


First you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.



Jun 01, 2010 | 2000 Audi A6

1 Answer

My front wipers arent working, could it just be the fuse? if so which fuse do i change as the list only has my rear wiper on it.


Fuse nr.31, F31, (25A) = Windscreen wipers
This fuse is placed on fuse box / relay plate engine bay 1, under bonnet in engine compartment area!

If the fuse F31 is OK.
You must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows:
1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Jan 13, 2010 | 2006 Audi A3

1 Answer

My windscreen wipers work on the higher settings


hi the wiper stalk is at fault regards

Oct 03, 2009 | 2002 Jaguar X-Type

1 Answer

Eratic front wiper motor on a 1996 A4


It is not very difficult to replace the wiper motor, but first you must diagnose this problem. In order to find out the cause of wipers stopping you can try follows:
1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor.
It is not very simply, but it works.
Heed of the windscreen !!!
Refit in reverse order.
Success!


Nov 14, 2008 | 2004 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15387 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...