Question about Cars & Trucks

Open Question

2.5l turbo diesel wl mazda drifter

Cylinder head, injectors, camshaft cups

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

czaa
  • 4514 Answers

SOURCE: Please describe cylinder head

please buy a repair manual asap--or go to library sec629

Posted on Feb 14, 2011

ZJLimited
  • 17970 Answers

SOURCE: 2000 Mazda Drifter 2.5 Turbo

Mazda B2200, B2500 and B2600 (6th Generation).

In model year 1998, Mazda B series renews its own international markets. Production at the plant AutoAlliance Thailand began in May 1998. This model is also sold as the Ford Ranger in Europe and Asia, and the Ford Courier in Australia and New Zealand. Production started this year in the factories of companies AutoAlliance Thailand and Ford Motor Philippines. Versions CKD are also assembled in South Africa, Ecuador and Colombia.

The van is sold in over 130 countries under a variety of names. Along with the emblems of Fighter and Ranger in Southeast Asia (except Singapore, which served as the flagship models Proceed Japan), was sold as the Mazda Bounty and Ford Courier in New Zealand, Mazda Bravo in Australia, and Mazda Drifter in South Africa.

Engine options:
2.2 L 2.2 L (2.184 cc) 85 hp (63 kW)
2.5 L (1.998 cc) turbo diesel 118 hp (88 kW)
2.6 L (2.606 cc) 121 hp (90 kW)


zjlimited_1152.jpg

Fig. Tighten the exhaust manifold bolts in 2 stages

To install:

  1. Clean the mating surfaces on the exhaust manifold and the cylinder head.
  2. Install a new gasket and the exhaust manifold. Torque the bolts in sequence as follows:
    1. 16 ft. lbs. (23 Nm).
    2. 59 ft. lbs. (80 Nm).

Hope helps.

Posted on May 01, 2011

SOURCE: help me to remove my cylinder head of my mazda 2005 drifter b250

  • Hi Ronald, Get ready for a lot of work! The first thing is to clean the engine of all dirt and contaminants that may cause damage when the head id removed. When the engine is cold disconnect the battery. Remove the air cleaner ducting and housing and then drain the coolant from the radiator and engine block. The coolant drain plug on the engine block sometimes becomes corroded so be careful and if it is too tight leave it. Get yourself some masking tape and mark all the relevant electrical connections before removing them. If your engine is the type with timing gears turn it to Top Dead Center (TDC) and once set leave it. If it has a timing belt remove the front plastic timing cover and look for and identify the match marks for valve timing. If you can't see them make your own marking the TDC positions of the camshaft in relation to the cylinder head, (This may save you a lot of pain and suffering later) If the engine is diesel, identify or match mark the timing gear in relation to Crank Shaft and Cam Shaft. Remember the body of the injector pump when turned is also an adjustment so match mark the pump body to the engine. With a diesel, mark the pipes and make a sketch of where each pipe fits onto the distributor type pump. (Do not bend the pipes) If it's a petrol engine mark the position of each of the HT plug leads, remove the distributor cap and sketch the position of the rotor arm in relation to the cap. (In other words note which way it's facing. Remove the cap and the plug leads. mark all vacuum tubes for later reinstatement before disconnecting. Disconnect all electrical connections (Which you should have marked) Remove the tappet cover and clean the oil, which should be correctly taken care of. If the engine has a timing belt, loosen the tensioner bearing to its maximum adjustment and making sure that the timing marks are still aligned remove the belt. If it has a belt it will usually have overhead cam. If gears it will likely have a rocker shaft assembly and push rod operated valves. Begin to loosen these from the front and back working in to the center of the head. Loosen each bolt evenly, one turn at a time until the whole cam or rocker assembly is loose and can be removed. Keep in mind that up until this point certain valves will be open and under tension Once removed the the valves will then be fully closed. Remove the intake and exhaust manifolds, alternately loosening from each end working towards the center. Remove the radiator cooling hoses and ensure that bypass hoses are removed too. Make sketches of the fitting positions before removal. Closely inspect all areas where bolts and brackets may impede the removal, and if any remain, remove them. Careful inspection and recording will help you greatly during assembly. You are now ready to remove the cylinder head. Begin at the front of the engine by loosening the first bolt of the cylinder head and then go to the rear and loosen the bolt diagonally opposite. Follow the same loosening sequence working towards the center until all bolts are loosened. and then remove them. The cylinder head can now be removed. In the case of the engine being diesel powered, look at the outer edge of the gasket where you should see an indicator of the gasket thickness. This is very important when buying the replacement gasket (never reuse an old gasket) The thickness is in relation to the piston protrusion above the engine block and if the replacement is too thin, the valves will collide with the pistons during operation (which ain't very good for pistons or valves!) If the gasket is too thick the compression will not be achieved for maximum performance. I suggest that when the head is removed, after cleaning it should be taken to an engineering company for checking and if warped it should be lightly skimmed. The tightening sequence is opposite to removal, meaning begin at the center and work outwards. This applies to the cylinder head, manifolds and tappet cover. In fact not a bad idea for everything you apply a spanner or wrench to. Ps. Why do you want to take the head off? Just asking. Regards John

Posted on Jun 30, 2012

  • 80 Answers

SOURCE: mazda drifter 2.5 diesel pulls left when brakeing

it could be that the right side caliper is stuck in the open condition. there is something blocking the brake fluid to the caliper or the piston is defective and is stopped mechanicly. jack up and block truck remove front tires, with a helper have them push on the brakes while you observe the calipers if the left piston moves and the right doesn't then you have found the problem. now trouble shoot unscrew the bleeder valve and have assistant push on the brakes. If fluid comes out then it is the caliper. If no fluid then work your way back toward the master cylinder at every connection. sometimes the rubber hoses that go to the caliper rot from the inside out causing a no fluid getting thru problem. hope this helps

Posted on Jul 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque settings on the 2.5 liter turbo WL diesel cylinder head


cant find that motors engine repair manual today

might be in here... has diesel motors listed

DF]Complete Cylinder Head Torque Specifications for Domestic and ...

fme-cat.com/LiveDocs/99999.pd

Oct 21, 2016 | Cars & Trucks

1 Answer

What is the main bearing bolt torque for Mazda b2500 WL engine? Thanks


got the repair manual for the
WL engine 676 page zip pdf type file
used in the ranger and drifter
down load and find
ranger drifter engine body and chassis folder
look for
the ranger drifter repair manual ..its 13882 kb

this uses cloud and is safe at the moment
http://www.trinituner.com/v4/forums/viewtopic.php?t=326401
any b2500 engine must all use the same block
looks like mazda had a play with the top ends

..only page 70 has the block drawing
doesnt say ftbs or nm
being metric and mazda would assume nm
this is lined to the crank bearing cap bolts
83-88 ( 8.4-9.0 61-65)

Jun 08, 2016 | Mazda Cars & Trucks

1 Answer

Gloplug diagram for mazda drifter 2.5 turbo diesel


type your question into google and click images might take you a whileto find but should be on there.

Apr 06, 2016 | 2006 Mazda Drifter 2.6

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl


con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Dec 25, 2013 | Saab 9 Cars & Trucks

1 Answer

Tappet Settings for Mazda Drifter 2.5 Turbo diesel


  • Tappet clearence for Mazda 2.5 diesel turbo 2002 model

Aug 10, 2013 | Cars & Trucks

1 Answer

Help with torque setting for mazda b2500 wl diesel engine


What is de torque for wl 2500 mazda main bering. Thanks

Mar 25, 2013 | Cars & Trucks

1 Answer

2000 Mazda Drifter 2.5 Turbo Diesel, exhaust manifold torque settings for nuts.


Mazda B2200, B2500 and B2600 (6th Generation).

In model year 1998, Mazda B series renews its own international markets. Production at the plant AutoAlliance Thailand began in May 1998. This model is also sold as the Ford Ranger in Europe and Asia, and the Ford Courier in Australia and New Zealand. Production started this year in the factories of companies AutoAlliance Thailand and Ford Motor Philippines. Versions CKD are also assembled in South Africa, Ecuador and Colombia.

The van is sold in over 130 countries under a variety of names. Along with the emblems of Fighter and Ranger in Southeast Asia (except Singapore, which served as the flagship models Proceed Japan), was sold as the Mazda Bounty and Ford Courier in New Zealand, Mazda Bravo in Australia, and Mazda Drifter in South Africa.

Engine options:
2.2 L 2.2 L (2.184 cc) 85 hp (63 kW)
2.5 L (1.998 cc) turbo diesel 118 hp (88 kW)
2.6 L (2.606 cc) 121 hp (90 kW)


zjlimited_1152.jpg

Fig. Tighten the exhaust manifold bolts in 2 stages

To install:

  1. Clean the mating surfaces on the exhaust manifold and the cylinder head.
  2. Install a new gasket and the exhaust manifold. Torque the bolts in sequence as follows:
    1. 16 ft. lbs. (23 Nm).
    2. 59 ft. lbs. (80 Nm).

Hope helps.

May 01, 2011 | Mazda B2600 Cars & Trucks

2 Answers

Please describe cylinder head torque secuense mazda wl DIESEL 2007 turbo 2.5


The head torquing sequence is as below:-

9....5....1....3....7
Front
10...6....2....4....8

Carry out the sequence at least three times, once at about half the torque value and then at least twice at the full value.

Feb 14, 2011 | Mazda B-Series Truck Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...