Question about Cars & Trucks

Open Question

How to remove inside door panel peterbilt model 387

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
kf4rwe
  • 25 Answers

SOURCE: Door Panel removal

remove all visable screws from panel and arm rest. Arm rest should come off. Use a flat thin tool or piece of metal and slip it between the panel and the metal door frame. Slip it in about 2 inches,. Slide it back or forth til you hit a stop. That should be a plastic pop in.twist metal tool to pull panel away from the door. It should pop away from door frame. Don't overdo it if it doesn't come out. try another spot. once you get one loose, you can tell how to get the others out. Once panel is loose push it upwards to get top lip out of window bottom. If it has power windows,disconnect plug. If it has manual windows, you will have to remove the window crank There is a snap ring behind window crank that has to be removed.push in on panel by window crank and you can see the ring.

Posted on Dec 06, 2008

Ad
  • 75 Answers

SOURCE: remove inside door panel without breaking it

they have push in clips that hold the panel on the door you can pull it off with your hand or go to parts store and buy a door panel removal tool
PLS take time to rate this solution and by the way you will probably need to buy new push in clips to hold panel on

Posted on Feb 17, 2009

  • 295 Answers

SOURCE: how remove the rear inside door panel on a 2001 oldmobile aurora

The inner door panel is held in by clips and screw.
Look at the door near the door handle there should be screws holding it in and along the outer edge of the door. Once loose, and the door handle removed or the arm rest removed. The door panel then prys out , because of the clips that hold it on. Then pops out by applying pressure to the panel upward to the top of the door. The clips always break because of the design and plastic.

Good luck

Posted on Mar 21, 2009

  • 1986 Answers

SOURCE: 94 LeSabre inner door panel removal

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

  • 275 Answers

SOURCE: remove the inside rear door panel for 1995 Landrover

Remove the 2 bolts holding the grab handle ( 10mm) Remove the screw holding the pull handle plastic cover and remove the cover. Use a fork and pry the panel away from the door and you will be able to pull it off. Before refitting, check all of the plastic clips that hold the panel to the door, some will have broken off. Remove them and fit them back on to the trim panel and glue them on. Refit is reverse as removal. Hope that helps

Posted on Mar 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need fuse panel diagram for 2003 Peterbilt 379 vin# 1XP-5DB9X-8-3N801030.


We would have the same fuse diagram. so can't really help.

May 28, 2016 | Cars & Trucks

1 Answer

2009 peterbilt 387, hard to steer when start driving in the mornings & parking. Once on the road she loosen up and drives fine. What's the problem?


Could be low on power steering fluid?
Even the electro-hydraulic pas systems use fluid.

If it isn't that, the problem should be investigated in case it is safety related. It could be a tight track rod end or steering swivel ball joint or a semi-seized strut swivel bearing. If rectification isn't carried out component failure could be the eventual result with the possibility of some very exciting consequences as a piece either breaks or falls off...

May 13, 2016 | Cars & Trucks

1 Answer

2010 peterbilt 387. Why doesn't heat come out?


check that the heater control tap is being turned on when you select hot
check for air trapped in the heater core and not allowing hot water to circulate

Oct 05, 2015 | Cars & Trucks

1 Answer

2015 Peterbilt 387. Why doesn't the heater work?


It's so new you should not have a problem but you are not getting coolant to flow through your heater core. I suspect an electrical problem around the water shutoff valve or a vacuum hose or cable not opening the heater valve. You might be able to manually open the heater valve.

Oct 05, 2015 | Cars & Trucks

1 Answer

Where is the abs located on a 2001 387 peterbilt


on any car/truck it is going to be near the brake master cylinder, so follow the brake lines from there.
----------
carprog full v4.01

Mar 04, 2013 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,731 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...