Question about 2006 Cadillac CTS

Open Question

Rear bumper plastic cover is loose

How do I tighten my rear plastic cover on a 2006 cts

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dj_ricko_198
  • 128 Answers

SOURCE: My 2004 CTS "service airbag"

did you get this car new and if it is under warranty take it back
pushing the cover back on can pinch the bag and cause it not to work
this could cause the light to come on
have it checked and take great caution when putting cover on cause it can activate the airbag and cause damage to you

Posted on Dec 28, 2008

  • 41 Answers

SOURCE: 2006 cadillac cts wind shield washer reservoir is

it might be possible by removing the shields but most of the time requires removing the bumper cover.

Posted on Mar 04, 2011

Testimonial: "Thanks for the info. I didn't want to take more parts off the car than i have to. Will take it slow and maybe i will be able to get to it from below. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace rear parking sensor


You have to take bumper cover off .
Remove rear bumper fascia. Refer to Rear Bumper Fascia Replacement . Disconnect electrical from the rear object sensor. Lift the locking tabs on the housing and remove the rear object sensor.
Preliminary Procedure
  1. Remove the compartment sill plate. Refer to Rear Compartment Sill Trim Plate Replacement .
  2. Remove rear wheel liners. Refer to Rear Wheelhouse Panel Liner Replacement .
1
Rear Fascia Push Pin Retainers (Qty: 2)
2
Rear Fascia Nuts (Qty: 4)
Tighten
10 N?·m (89 lb in)
3
Rear Fascia Bolts (Qty: 2)
4
Rear Fascia Bolts (Qty: 6)
5
Rear Fascia
Tip
?€¢
Energy absorber and fascia are removed together. Cannot be separate on vehicle.


?€¢
Disconnect the electrical connectors.

Dec 22, 2015 | 2006 Cadillac DTS

1 Answer

The rear bumper cover came off how can I reinstall it


2000 Toyota Sienna rear Bumper cover replacement (1998 ...

? 3:40
https://www.youtube.com/watch?v=AY1BBdg3q74
Sep 20, 2013 - Uploaded by SergSpace
2000 Toyota Sienna rear Bumper cover replacement (1998-2003) .... Automotive Bumper Repair Specialist- How to repairyour plastic bumper cover ... Toyota Sienna Rear Shock Installation 2003, 2004, 2005, 2006 - Duration: ... 2015 Toyota Sienna XLE - Duration: 28:13. by MikesCarInfo 35,234 views.

Fixing My Mom's Prius: Loose Rear Bumper Cover - YouTube




Nov 29, 2015 | 2005 Toyota Sienna LE

3 Answers

How do I change right front head light


The 2008 CTS is the same as my 2009 CTS.
To access the any of the bulbs, you need to remove the bumper/grille assembly.
I just did mine and installed some aftermarket HID bulbs.
If you have some skill and patience, it will take you around an hour.
I'll try to remember all the steps, but I did find a video on youtube that shows it very well:
Remove the long plastic cover over the radiator, by unscrewing the 6 plastic clips. There some rubber molding attached, but you can just flip the cover over on top of the engine.
This exposes 2 10mm screws that can be removed - they'll look like they are attached to the grille. Don't remove them yet.
If front of each front tire in the edge of the wheel well, there are two plastic pins. The pins are actually two pieces, pry the center piece straight out about a quarter inch, then the whole pin can be popped out.
Under the front lower edge are 5-7 similar clips that need to be removed the same way. There about 15-20 of them under there, but you don't have to remove them all. I recall that two of them are upside down.
Now he scary part.... back to the wheel well. Get a flashlight. I recall the inner fender is under the bumper edge; it needs to be pulled out from behind the bumper. Then pull the inner fender backwards from the bumper; it's very stiff, but you need to pull it about 3/4" and look straight up through the gap. There is a 10mm screw, about one inch from the edge of the bumper/fender. This screw holds the bumper to the fender. Use a 10mm socket and a long extension to remove it. (do both sides)
Then you can firmly pull the side of the bumper sideways from the car.
There are 4 of those plastic pin/clips to removed under the hood, next to the headlight. Then you can remove the two 10mm screws under the hood, and the bumper can be lifted off.

Each of the headlight housings are held on by two 10mm screws and a 10mm nut. The is one electrical connector to unclip.

There are 3 covers on each housing. Each cover is held on by 3 8mm? screws. Your low beam is the top bulb.


25548514-wfi1xyowpghsdcre2c1nwnv2-3-1.jpg

25548514-wfi1xyowpghsdcre2c1nwnv2-3-3.jpg

25548514-wfi1xyowpghsdcre2c1nwnv2-3-6.jpg

25548514-wfi1xyowpghsdcre2c1nwnv2-3-10.jpg

25548514-wfi1xyowpghsdcre2c1nwnv2-3-15.jpg

Mar 10, 2015 | 2008 Cadillac CTS 2.6

1 Answer

I need to replace the rear fog light cover in the bumper of a 2006 grand cherokee. Do I need to take the bumper off to do so?


FSM 101 or the parts list. shows this.
the parts list show 2 types.
one in the main lamp. ID 7 in drawing
then the optional bumper fog kit, rear.
so bumper. but since its and option, its not that well covered.
not in fsm i bet. did you look.?
so here is my best guess.
the kit shows NO SCREWS.
so just pry's off
see it here.

http://www.factorychryslerparts.com/showAssembly.aspx?ukey_product=4612193&ukey_assembly=1122497

or im wrong and you must gain inside access
to trip the plastic locking lever on lamp.
as you see the lens is not SOLD.
so?

Mar 31, 2014 | 2006 Jeep Grand Cherokee

2 Answers

How do I remove the back bumper from a 2006 hyundai tuscon?


take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.
  1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
  2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
  3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
  4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
  5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.

  6. Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.

Dec 27, 2010 | 2005 Hyundai Tucson

2 Answers

I have a 2006 Ford Explorer and 2 of my park aid assist sensor are bad. They are in the rear bumper. How would i replace the sensors? Is it really necessary to remove the bumper?


You only need to remove the bumper cover. Remove both tail lamp assemblies. Under the tail lamps you will a 10mm and a 8mm bolt, remove these. Look into each rear wheel well rearward and you will find a T20 torx screw on both sides, remove these. On the top of the rear bumper, between the bumper and the bottom of the liftgate opening you will find 6 to 8 plastic rivets that can be removed by pulling the center pins out, remove these. At this point you should be able to lift upward and rearward and release the bumper cover. Once the cover is free you must disconnect the electrical connector to the sensor wiring harness. With the bumper cover on the ground or a bench, you will see 4 9/16" nuts that hold the styrofoam bumper cushion to the bumper cover, remove these. Now you should be at the point where the backup sensors are accessable. When you install the new sensors be sure your electrical connectors click when they connect. these connectors go on hard and if they don't click you will be doing this job again. Reassemble in reverse order.
Hope this helps

Apr 01, 2010 | 2006 Ford Explorer

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

1 Answer

Chrysler 300c rattle in bumper rear


Fold dollar bills and wedge them into the gap of area rattling.

Aug 24, 2009 | 2006 Chrysler 300

1 Answer

Change headlight


hello. below is the procedure for removal of the headlamp for bulb replacement. to access the headlamp you will need to remove the bumper fascia. http://gsi.xw.gm.com/image_en_us/gif/000/001/725/1725371.gif Callout Component Name 1 Front Compartment Sight Shield Plastic Retainers (Qty: 6) 2 Front Compartment Sight Shields (Qty: 3) Tip Each front compartment sight shield is serviced separately as needed for repairs http://gsi.xw.gm.com/image_en_us/gif/000/001/728/1728611.gif Callout Component Name Preliminary Procedure Remove the front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement . 1 Front Fascia Extension Plastic Retainers (Qty: 5) 2 Front Fascia Extension http://gsi.xw.gm.com/image_en_us/gif/000/001/733/1733942.gif Callout Component Name Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications: Refer to Fastener Tightening Specifications . Preliminary Procedures Remove the front compartment sight shields. Remove both front bumper fascia extensions. 1 Front Bumper Fascia Reinforcement Nut (Qty: 2) Tighten 6 N·m (53 lb in) 2 Front Bumper Fascia http://gsi.xw.gm.com/image_en_us/gif/000/001/736/1736893.gif Callout Component Name Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications: Refer to Fastener Tightening Specifications . Preliminary Procedure Remove the front bumper fascia. 1 Headlamp Nut (Qty: 1) Tighten 6 N·m (53 lb in) 2 Headlamp Bolts (Qty: 3) Tighten 6 N·m (53 lb in) 3 Headlamp Assembly

Jun 13, 2009 | 2003 Cadillac CTS

Not finding what you are looking for?
2006 Cadillac CTS Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...