Question about Suzuki Kizashi

Open Question

How to Remove Center Console in Suzuki kizashi

How do I remove the center console box on a Suzuki kizashi, to loosen the parking brake adjustment nut?

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22246 Answers

SOURCE: how to remove center console of a 2001 LX honda accord 4 cylinder

You should never need to adjust the cable what i suspect here is the back brakes need looking at ,but before i can tell you how to do it i will need to know if its
A drum brakes
B disk rear with cable to caliper
C rear disk with cable running to the interior of the disk and not to the caliper

Posted on Apr 15, 2012

Ad
alicantecoli
  • 22246 Answers

SOURCE: how do I get to the parking brake adjusting nut under the center console of a 2001 honda accord LX

If handbrake has excessive travel and the brake pedal is low then you havent set the rear brakes up properly ,if a drum then you clean the lip on the edge of the drum so it has a bevel then you manually adjust the auto adjuster till the drum just slides over then tap outer edge of drum wth a small hammer to level the shoes and then see if you can then adjust the auto adjuster up a bit more .Also when taking the drum off again make sure that the handbrake mechanism lever is right back ,Now if you adjust the brakes on the handbrake cable then it will be out of square and will not work on a brake roller tester ,and the footbrake will still feel spongey then you get a inspection failure for excessive pedal travel and low handbrake efficiency ,this model of car should be able to lock the rear brakes up at 30mph when jerking the handbrake up hard and it shouldnt have more than 3 clicks when done correctly

Posted on Apr 15, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust handbrake


If you remove the center console you should be able to get at your adjusting screw. The end of the brake cable where it attaches to the brake handle will usually have a large threaded area for adjustment with an adjustment nut and a jamb nut. Simply loosen the jamb nut and set the desired cable tension with the adjustment nut and tighten the jamb nut back down. Then replace the console. If you are unable to get the desired tension at the cable you might have worn brake shoes that need replacing.

Sep 01, 2014 | Cars & Trucks

1 Answer

Adjust handbrake 94 libero


  • Remove the center console covering the parking brake lever. Locate the parking brake lever between the drivers seat and the front passenger seat. Put the parking brake lever in the lowest position.

  • 2

    Turn the cable adjuster locknut to make the nut loose. Find the nut at the base of the parking brake lever.

  • 3

    Raise your GT rear wheels using a jack and support the rear wheels using jack stands. Remove both rear wheels using a tire iron to loosen and take off the lug nuts. Take off the tire from the rods by hand.

  • 4

    Get underneath the car and remove the rubber hole plugs from the brake rotors. Locate the rotors on the underneath inside of the wheel wells.

  • 5

    Take off the brake calipers with a screwdriver, but do not disconnect the brake fluid lines.

  • 6

    Use a pry bar to push up on the parking brake self adjuster wheel. Locate this next to the brake caliper and it looks like a star wheel. Rotate this wheel until the rotors will not turn.

  • 7

    Turn the adjuster wheel five notches in the opposite direction. Reinstall the calipers and wheels. Lower your GT using the jack and remove the jack stands from the rear wheels.


  • Sep 13, 2012 | Mitsubishi Cars & Trucks

    1 Answer

    I have just replaced all the discs and pads on my 2004 mazda 3, but the handbrake is very loose, does this require to me manualy adjusted. Thanks Murray


    YES, if brakes are ok! then adjust the e-brake. heres how, Start the vehicle and press down and release the brakes four times. Turn off the engine. Remove the hooks from the center console and lift off the cover. The center console is located in the inside front of the car between the driver's and the passenger's seats. Adjust the nut under the console by tightening it with pliers.

    Lift up the parking brake handle one click. Turn the engine on and look at the control panel. You should see the parking brake light. release parking brake and raise rear to make sure the wheels turn freely. forward and backwards. good-day !

    Sep 13, 2011 | 2004 Mazda 3

    1 Answer

    My handbrake is not holding on a hill brakes seem fine I want to do it my self please help


    YOU WILL NEED A HAYNES REPAIR MANUAL OR FACTORY MANUAL ON CD.BECAUSE ON BMW YOU HAVE TO REMOVE CENTER CONSOLE AND ARMREST TO GAIN ACCESS TO THE PARKING BRAKE LEVER. PARKING BRAKE CABLE CONSISTS OF TWO SECTIONS A RIGHT AND LEFT HAND SECTION, WHICH ARE CONNECTED TO THE LEVER.YOU HAVE TO LOOSEN REMOVE THE RELEVANT PARKING BRAKE CABLE LOCKNUT AND ADJUSTING NUT AND DISENGAGE THE INNER CABLE FROM THE PARKING BRAKE LEVER. IF YOU FIND A HAYNES BMW REPAIR MANUAL WITH HAND BRAKES.THAT WILL SHOW AND TELL YOU STEP BY STEP INSTRUCTION HOW TO ADJUST PARKING BRAKE CABLE ADJUSTMENT. I COULD TELL YOU HOW TO DO THE JOB. BUT YOU NEED TO SEE PHOTOS AND INSTRUCTIONS BECAUSE YOU NEED TO SEE WHERE YOU NEED TO MAKE CABLE ADJUSTMENTS.NOT EASY TO TELL YOU.

    May 06, 2011 | BMW 325 Cars & Trucks

    1 Answer

    How do i repair shifting cable from cosole to trans.?


    Welcome to FixYa.com



    REMOVAL
    1. Remove air cleaner and air intake hose assembly.
    2. Remove center dash trim panel.
    3. Remove center console cup holder assembly.
    4. Remove floor console assembly.
    5. Remove console side panels.
    6. Remove Transmission Control Module ftMJ bracket.
    1. Remove TCM.
    8. Remove shifter cable from transaxle operating lever by removing nut and clip.
    9. Remove shifter cable from shifter lever assembly by removing clip.
    10. Remove shifter cable from shifter lever mechanism.
    11. Remove cable from firewall grommet by removing grommet assembly nuts.
    12. Remove gearshift cable from vehicle.
    ADJUSTMENT
    Lift and rotate the gearshift hand lever into the park (F9 gate position and remove the ignition
    key. This confirms the shift lever is in the gated park (F9 position.
    After confirming the park gate position. turn the ignition switch . If the starter will operate. the
    park gate position is correct. Move the shift lever into the neutral (NJ position. If the starter
    will operate in this position, the linkage is properly adjusted. If the starter fails to operate in
    either position, linkage adjustment is required.
    1. Park the vehicle on level ground and set the parking brake.
    2. Place the gearshift lever in park (F9 gate position and remove key.
    3. Loosen the cable adjustment screw at the transaxle operating lever.
    4. Pull the transaxle operating lever fully forward to the park detent position.
    5. Release the park brake, then rock the vehicle to assure it is in park lock. Reset the park
    brake.
    6. Tighten the cable adjustment screw to 8 Nm (10 inch Ibs.J. Gearshift cable should now be
    properly adjusted.
    1. Check adjustment by usinq the precedinq procedure.



    Thank you for Using FixYa.com

    Kind Regards, Lee

    Your Master Technician FixYa Expert

    leedavidian_98.png

    Jan 31, 2011 | 1997 Chrysler Sebring

    2 Answers

    How do I adjust the parking brake cable on a 1991


    If the car has a center console between the seats, and the e-brake lever is there, remove the console there should be a bolt to tighten or loosen. Loosen it with the lever DOWN, pull the cable as tight as it will go with your hand and a pair of pliers. Holding the cable in place tighten the bolt or nut that secures the cable. If this doesn't fix it, have your rear brakes inspected and/or adjusted.

    Oct 03, 2009 | 1991 Mercury Tracer

    1 Answer

    Shifter alignment cable is out of place, how do i fix it ? If I put the car in drive it roles backwards. I have to drive with the car on 4.


    To Adjust : 1- Unclip parking brake boot. 2- Detach the center console upper section. 3- Disconnect cigar lighter electrical connector. 4- Remove te center console upper section , disconnect the transmission mode and traction control electrical connectors 5- Move the selector lever to position "R" 6- Loosen the selector cable lock nut 7- Detach the selector cable. 8- Raise and support the car. 9- Move the Rotary position switch to the "R" position , so that it matches the lever. 10- Lower the car. 11- Connect the selector cable (Do not tighten selector lever lock nut) 12- Move selector lever to "D" , hold the selector lever applying light pressure and fingure tighten the rear lock nut , then fingure tighten the front lock nut 13- Now move the lever to different gear positions , ( when "D" is selected , make sure it sits as close as possible to the "D" and "4" position in each corner. 14- Tighten selector lever lock nut. 15- Install center console upper section. (connect the transmission mode and traction control electrical connectors) 16- Connect the cigar lighter connector 17- Install the center console upper section. 18- Clip together the parking brake boot.
    And you are done , I know it looks hard but it is not , read through my instructions and understand it and all will be easy to do. Good luck , hope it helped :)

    Jul 27, 2009 | 2001 Jaguar S-Type

    1 Answer

    How to adjust hand break hyundai elantra 2000 model


    1. Remove the console upper cover.
    2. Remove the crash center facia panel.
    3. Remove Console Assembly.
    4. Adjust the parking brake lever stroke.

    You may not have to remove all of these pieces, just enough that you can access the adjusting nuts. Make sure both cables have tension, they are famous for breaking, and making the other side too loose.

    May 11, 2009 | 2005 Hyundai Elantra

    1 Answer

    How to disconnect the handbrake cable from the trailing arm


    There are tie clamps at the rear, but the entire cable is a complicated repair.

    028b64d.gif
    Parking Brake Cable Removal
    All vehicles
    1. Remove the floor console. For additional information, refer to Section 501-12 .
    1. Release the parking brake.
    1. NOTE: Leave 5 mm of thread protruding from the nut, to aid with installation.
      Loosen the parking brake cable adjustment nut.
      1. Remove the retaining clip.
      1. Loosen the adjustment nut.
    1. Remove the rear wheels and tires. For additional information, refer to Section 204-04 .
    1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the exhaust pipe.
      Detach the tailpipe and muffler assembly.
      1. Remove the nuts.
      1. Unhook the hanger insulators.
    2. Detach the center hanger insulators.
    3. Remove the exhaust front heat shield.
    4. Remove the exhaust center heat shield.
    5. Detach the exhaust rear heat shield from the floor panel.

    Feb 24, 2009 | 2000 Ford Focus

    1 Answer

    How can i find out my parking brake adjustments on my 2003 ford escape?


    Parking Brake Cable Adjustment Vehicle with low series floor console
    1. Remove the floor console front finish panel.
      1. If equipped, remove the manual transmission shift knob by turning counterclockwise.
      1. Remove the floor console front finish panel.
    1. Remove the floor console rear finish panel.
      1. Apply the parking brake.
      1. Remove the floor console rear finish panel.
    Vehicle with high series floor console
    1. Remove the floor console finish panel.
      1. Apply the parking brake.
      1. Remove the floor console finish panel.
    All vehicles
    1. Remove the adjustment nut clip.
    1. Turn the parking brake control adjustment nut so that the parking brake control stroke is three to five notches when pulled.
    1. Confirm the parking brake is applied.
    1. Install the adjustment nut clip.
    Vehicle with high series floor console
    1. Install the floor console rear finish panel.
    Vehicle with low series floor console
    1. Install the floor console rear finish panel.
    1. Install the floor console front finish panel.
      • If equipped, install the manual transmission shifter knob by turning clockwise.

    Jan 21, 2009 | 2003 Ford Escape

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    270 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Suzuki Experts

    yadayada
    yadayada

    Level 3 Expert

    76848 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Boyet Soriano
    Boyet Soriano

    Level 2 Expert

    293 Answers

    Are you a Suzuki Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...