Question about Cars & Trucks

Open Question

Replace fan belt on 555 ford backhoe - Cars & Trucks

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 400 Answers

SOURCE: Where is place to add

There should be a dipstick located in the cab or on the right side of cab. If in the cab, under the floor mat there is a trap door. The tranny is directly under the cab.

Posted on Apr 04, 2011


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace the throttle cable on a Ford 555 C backhoe. The one that runs from the pump to the foot accelerator.

good question

accelerator cable pedal to pump

if not available off the shelf
might need to be made using the old one as a sample

closest repair manual i could find online


Dec 07, 2016 | Ford Cars & Trucks

1 Answer

1992. How do I replace fan belt? fan belt

There is a spring loaded belt tensioner. Use the appropriate tool to release the tension on the belt Remove the belt , paying attention to the belt routing and replace the old belt with the new belt.

Oct 13, 2015 | Ford Explorer Cars & Trucks

1 Answer

I need a routing diagram for serpentine belt on a John Deere 310SE backhoe?

You should be able to get that by going to the website for Gates rubber and belts.

Sep 12, 2014 | Cars & Trucks

1 Answer

Replace fan belt

draw a diagram of the old belt position before starting so that you can remember where it goes. The idler pully will have a nut that has to be loosened. Just behind the idler will be a long bolt that when turned releases the tension on the belt. screw it until you can easily remove the belt. replace the belt as per your diagram and retension the belt when you are satisified that sufficient tension on the belt exists tighten up the nut of the idler pulley

Jan 08, 2013 | Ford Cars & Trucks

2 Answers

Where is place to add transmission fluid in ford backhoe 555 diesel?

There should be a dipstick located in the cab or on the right side of cab. If in the cab, under the floor mat there is a trap door. The tranny is directly under the cab.

Apr 04, 2011 | Ford Transit Connect Cars & Trucks

1 Answer

Need to replace my fan belt.

auot zone or advance auto might be able to help

Feb 10, 2009 | 1997 Ford Escort

1 Answer

Broken timing belt 1997 ford crown victoria

no... the 97 crown vic has a timing chain not a timing involve 7.4 hrs book time to replace with gears to include front gaskets and timing kit about 200+ in parts and at 75 an hr ..555 in labor..guessing less than 1k to do the job ..(here in california)

Dec 18, 2008 | 1997 Ford Crown Victoria

2 Answers

Changeing fan belts

fan bealt is easy to change all you need to do is right down how the belt runs befor you start and then loosen the alatanator and move it closer to loosen the belt then remove the belt around the fan and replace just like you wrote down then use a bar to tighten the belt by prying the altaator away from the motor but don't make it to tight then once tou have it as tight as you want tighten back the altanator and thats it

Dec 05, 2008 | 1983 Ford Fairmont

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15273 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides