Question about BMW Cars & Trucks

Open Question

How many does knock sensors does a 318i e46 engine have? bank

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: knock sensor location

It's under the intake manifold. To access it you have to remove the manifold and injection rail.

Posted on Dec 30, 2008

Ad
emissionwiz
  • 78254 Answers

SOURCE: e46 318i idle rev problem

GO TO A KRAGEN OR AUTOZONE AND HAVE THEM RUN A TROUBLE CODE TEST, THIS COULD BE A TPS PROBLEM, VACUUM LEAK OR STUCK/WARPED THROTTLE PLATE.

Posted on Feb 14, 2009

  • 3 Answers

SOURCE: bmw 318i e46 idle bad

try disconnecting the air mass meter sensor if it runs better then ur air mass meter has failed had the same problem

Posted on May 15, 2009

bmw_tech_38
  • 113 Answers

SOURCE: where is the crankshaft sensor on a e46 318i

the crankshaft sensor is located under the starter motor, you will have to remove the air intake manifold to gain access to replace the sensor, if you are not sure how to carry out this repair it would be better to get a local garage to do it, regards mark

Posted on Jun 11, 2009

  • 17 Answers

SOURCE: 2002 chevy silverado hd2500 6.0 ecm code po332 low

If all connections are good "dry, tight, no corrosion" then yes. It should be a defective sensor. These sensors are piezo sensors and create a voltage when sensing a knock. A bank refers to a side on a V style engine, 2 refers to the rear sensor on your bank 2. Bank 1 should be the side with cylinder #1 which should be the cylinder closest to you on one of the sides. So your looking for the rear sensor on the opposite side.

Posted on Jun 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Knock sensor for 2007 Saturn outlook. I can't pass emissions test!


Check engine light on ? What code ? There are many different (DTC'S) - diagnostic trouble codes that can set for knock sensors ! There all don't mean that you replace the sensor .
DTC P0324: Knock Sensor (KS) Module Performance
DTC P0325: Knock Sensor (KS) Circuit Bank 1
DTC P0326: Knock Sensor (KS) Performance
DTC P0327: Knock Sensor (KS) Circuit Low Bank 1
DTC P0328: Knock Sensor (KS) Circuit High Bank 1
DTC P0330: Knock Sensor (KS) Circuit Bank 2
DTC P0332: Knock Sensor (KS) Circuit Low Bank 2
DTC P0333: Knock Sensor (KS) Circuit High Bank 2

The knock sensor (KS) system enables the control module to control the ignition timing for the best possible performance while protecting the engine from potentially damaging levels of detonation. The sensors are located below each cylinder head on the engine block. The KS produces an AC voltage signal that varies depending on the vibration level during engine operation. The control module adjusts the spark timing based on the amplitude and the frequency of the KS signal. The control module receives the KS signal through 2 isolated signal circuits. The control module learns a minimum KS noise level at idle and uses calibrated values for the rest of the RPM range. The control module should monitor a normal KS signal within the noise channel.
Knock Sensor Replacement - Bank 1
Remove the exhaust manifold lower heat shield. Refer to Exhaust Manifold Lower Heat Shield Replacement.
Disconnect the engine wiring harness electrical connector (1) from the bank 1 knock sensor (2).
Loosen the knock sensor bolt and remove the knock sensor.
Knock Sensor Replacement - Bank 2
Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
Remove the engine oil filter. Refer to Engine Oil and Oil Filter Replacement .
Lower the vehicle.
Disconnect the engine wiring harness electrical connector (2) from the bank 2 knock sensor (3).
Loosen the knock sensor bolt and remove the knock sensor.

Nov 12, 2016 | Saturn Cars & Trucks

1 Answer

Where is the knock sensor located


This vehical has two knock sensors bank 1 and bank 2 ! bank 2 sensor screws into the side of the engine block closest to the firewall. and it is above the crank sensor. Knock Sensor (KS) Bank 1 sensor is on front side of engine block right of the oil filter and on the other side of knock sensor is the oil pressure sending unit.

Dec 26, 2014 | 2005 Saturn Relay

1 Answer

Circuit bank 2


Knock sensors are on the side of the engine block under the intake manifold. Bank 2 would be the sensor closest to the transmission above the starter as I recall.

May 24, 2014 | 1998 Volvo S70

1 Answer

How do i top up the automatic transmision fluid on my 1999 318i e46 bmw?


Get an owner's manual to be absolutely sure. 318i e46 too nice a machine to screw up...

May 18, 2013 | Cars & Trucks

1 Answer

What is code 325


P0325 - Knock Sensor Circuit Malfunction
Possible causes- Faulty knock sensor
- Knock sensor circuit short to ground
- Knock sensor circuit short to power
- Knock sensor circuit open
- Faulty Engine Control Module (very unlikely).
P0139 - O2 Sensor Circuit Slow Response Bank 1 Sensor 2

Possible causes- Rear Heated Oxygen Sensor Bank 1 harness is open or shorted
- Rear Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Rear Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

Sep 27, 2012 | 2000 Mercury Villager

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

2 Answers

2002 chevy silverado hd2500 6.0 ecm code po332 low voltage knock sensor 2 bank 2 does this mean knock sensor is deffective causing ecm to throw this code and if so should both sensor be replace and which...


If all connections are good "dry, tight, no corrosion" then yes. It should be a defective sensor. These sensors are piezo sensors and create a voltage when sensing a knock. A bank refers to a side on a V style engine, 2 refers to the rear sensor on your bank 2. Bank 1 should be the side with cylinder #1 which should be the cylinder closest to you on one of the sides. So your looking for the rear sensor on the opposite side.

Jun 13, 2010 | 2002 Chevrolet Silverado 2500HD

6 Answers

Bmw 318i e46 idle bad


try disconnecting the air mass meter sensor if it runs better then ur air mass meter has failed had the same problem

May 30, 2008 | 1999 BMW 318 ti

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Doberman

Level 2 Expert

254 Answers

dhnguyen

Level 2 Expert

281 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...