Question about Cars & Trucks

Open Question

How to remove a braking main fuse for a Ford Aspire 1996

The main fuse in engine fuse box is braking off.I'm using a pair of needle nose plires to try and remove the blown fuse.It is braking off & It won't come out.WHAT DO I DO NOW?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

greg_margo
  • 1959 Answers

SOURCE: 1996 Chevy S10 Hood Latch will not open

The best solution I've come across is a coat hanger used to pull on the cable from under the hood to get the latch to release. You can either place it through the grill or if there's room, just under the hood. Best of luck.
Greg

Posted on Jun 12, 2009

canbruce75
  • 1776 Answers

SOURCE: 1996 jimmy gmc fuse box

Look on the driver's side fender well under the hood. Should be a long black rectangular box there. That is the power center or fuse block. The relays and fuses are inside. The top is not hard to remove. Hope this helped and best wishes.

Posted on Sep 01, 2009

  • 1 Answer

SOURCE: I have an open 80 amp main battery fuse in the

my mazda 626 familia 97 the main engine fuse 80A was blown and my car totally dead..is it have a big electrical problem cause the fuse to blow up?

Posted on Jun 13, 2010

nampaboat
  • 150 Answers

SOURCE: We just hooked up our

First thing is your van equipped with a trailer brake controller and is it working. This is usually a small box that is installed inside the vehicle and is needed to operate the brakes. Next what type of plug do you have on the vehicle to plug the trailer into some plugs do not support wiring for trailer brakes. If you have a aftermarket trailer brake controller it will not be fused in the fuse panel so you will to locate a inline fuse used to power up the controller. Hope this helps.

Posted on Mar 04, 2011

dttech
  • 4803 Answers

SOURCE: vw polo abs light won't

Well, first of all, did you fix the problem that caused the fuse to blow? Have you scanned you Antilock Brake System (ABS) module for fault codes? Since the computer is the one responsible for turning the light on, wouldn't you think that the computer would be the one to ask WHY it has turned the light on?

Please also review the following articles:

Where's The Fuse?

What Else Could Be Wrong?

Posted on Sep 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't remove 30 amp fuse from console


Is the fuses melted in place. May need to use a pair of needle nose pliers.

Jun 13, 2012 | 2004 Chevrolet Malibu

3 Answers

Battery cables touched negative to positive car won't start


very good chance that you blew the computer, try needle nose pliers to get fuse out, omg i feel so sorry for you, good chance all the electronics are fried.

Jun 08, 2012 | 1997 Ford Aspire

1 Answer

Where is the radio fuse?


Below the dash, left of the steering column is the fuse box. It pulls open. There should be a diagram of the fuse locations. If there's not an attached fuse puller, take a pair of needle-nose pliers to pull the fuse.

May 07, 2012 | 1996 Mercury Mystique

2 Answers

How to replace 100 amp fuse next to battery under hood?


All what is needed is to get the same type replacement, remove the fused fuse from the holder and make sure that there is no crusting on the terminals of the fuse holder and the battery. There is clipped cover which can be removed to get access.

Dec 29, 2011 | 2001 Nissan Altima

2 Answers

98 ford windstar fuse box, need anti lock brake fuse location in fuse box


The sensor codes have to be read off a computer to see the problem, either speed sensor, sounds more like ABS module. Locate the main fuse/control box under hood. There should be either a relay or large fuse marked for abs.Good Luck.Please rate me as ' helpful ' if satisfied.

Jun 06, 2011 | 1998 Ford Windstar

1 Answer

Cannot get the rubber boots off the spark plugs and I don't know what to do. I don't think they were ever changed. I have manual but it doesn't say there is anything special to taking them...


The best thing to do, if you can get a grip on the boot, twist right and left then pull...i have a long pair of needle nose pliers special made to take plug wires off..You can buy from sears number is
(Knipex KNI3891200 quot;Grabberquot; Needle Nose Pliers- 8quot;)

May 21, 2011 | 1995 Ford Explorer

1 Answer

How do I remove the fuse box to replace the ALT Fuse? I removed the lower half of the fuse box, but can't seem to get the top half removed.


FUSE LINK LOOKS LIKE A FUSE.JUST USE FUSE PULLER OR PAIR OF SMALL NEEDLE NOSE PLIERS TO REMOVE FUSE OR FUSE LINK TO ALTERNATOR..BESURE THE BATTERY NEGATIVE CABLE IS DISCONNECTED FIRST TO KEEP SHORTING OUT OTHER FUSE LINKS AND FUSES IN THE CIRCUIT.TURN OFF RADIO FIRST BEFORE REMOVING NEGATIVE BATTERY CABLE

May 08, 2011 | Lexus ES 330 Cars & Trucks

1 Answer

How do I remove a type be fuse


There will be a fuse puller in the cover of the fuse box. OR just use a pair of needle nose pliers

Aug 27, 2010 | 2008 Toyota RAV4

1 Answer

I have a 1996 subaru legacy and I need to check the fuse box because the radio stopped working. the manual shows me where the interior fuse box is but mine doesn't look like the one they have. there is...


The interior fuse panel should have a cover on it that has the fuses labeled by number and description, there should be a fuse labeled radio. You can use a small pair of needle nose pliers if the under hood fuse box is also missing the fuse puller. that fuse box is mounted on your right hand side in front of the washer fluid reservoir if your looking at the front of the vehicle. I hope this info helps...(subytech1)...

Jan 22, 2010 | 1996 Subaru Legacy

3 Answers

Replacing the door ajar switch on my 1998 Lincoln Mark VIII


If you are getting the door ajar message you don't have to rplace the switch. Just spray it out good in the latch area with WD40. This will clean the switch contacts and make the message go away. I was a former Lincoln/Mercury mechanic and I used to see this problem on a daily basis. This was the Ford fix for this problem and the one I used on my own 98 mark VIII.

Feb 16, 2009 | 1998 Lincoln Mark VIII

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...