Question about Hyundai Cars & Trucks

Open Question

Chamberlain garage door opener program remote

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: remote garage door opener

1-800-355-3515
www.homelink.com

1. Position vehicle within 10 feet of garage door- engine off and battery on.

2. Press/hold 2 outside buttons of Homelink transceiver until red indicator starts flashing rapidly, then release button. This should take about 20 seconds. This erases any previously learned codes.

3. Press/hold remote control and press/hold button of Homelink transceiver simultaneously. Slowly move remote control from 5" away to 1" away from Homelink transceiver. Release both buttons after red indicator starts blinking rapidly. This should take about 5 seconds. I discovered that the Homelink in my TL is a bit faulty because it took much longer to accomplish this than when programming the Homelink in my MDX. My TL's Homelink may "unlearn" it's code in the future and the needed proximity of the TL to the garage door may be much closer than desired until I get the Homelink fixed.

4. Press training button on garage door opener unit until the indicator lights illuminates- this should be immediate.

5. Within 30 seconds press/hold the Homelink button for 2-3 seconds until the red indicator starts flashing rapidly. Repeat a second time. It should now be programmed. Check it by pressing the programmed button on the Homelink receiver.

6. When programming more than 1 garage door opener unit, disconnect power from unit before programming more units. By not doing this the programmed unit could conflict with the unprogrammed units commands.

Problems:

1. The Battery in the garage door remote may be too weak to program Homelink. However, the battery may be strong enough to operate the garage door. One of my remote controls had a weak battery- my system was installed today, fresh out of the box. I had to use the second remote control for the programming of Homelink on my 2 vehicles.

2. Antenna on the garage door opener unit must be hanging down, fully extended.

Posted on Dec 08, 2008

  • 1348 Answers

SOURCE: programming garage door opener

there are three buttons on the opener.hold the 2 outside ones down for 25 to 30 seconds to erase the program. once the light (if equipped)flash rate changes,let go.
then push any one of the the three buttons and hold it in. and then push your remote. when the flash rate changes,the code is now in the homelink transmitter.the slt and slt plus had that feature.

Posted on May 14, 2009

  • 150 Answers

SOURCE: In following the Chevrolet Tahoe instruction to program a garage door opener, I am having problems with the system working. The codes are the rolling key type.

Press the outer 2 buttons untill the bink rate changes then release.

Press the button you want to train at the same time you hold down an unused button on one of your factory GDO remotes, hold untill flash rate changes.

Press learn button on GDO, press the button you just programmed in the Tahoe, should be programmed.

(Info should be in users manual under HomeLink.)

Posted on Aug 07, 2009

  • 1 Answer

SOURCE: programming the garage door opener

Homelink Garage Door Opener Programming Procedure:

The procedure described below was successfully applied to a 2005 Jaguar S-Type.

To begin with, several attempts were made using the programming instructions contained in my Jaguars owners manual. Though the procedure described in the owners manual was straight-forward and understandable, I was unsuccessful in getting the vehicles remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the Rolling Code feature.

To begin with, be sure to clear previous codes on your Jaguars garage door opener by first turning (rotating) the ignition key to the I position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle buttons red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguars garage door opener console buttons. Choose which button on your Jaguars remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguars opener button. The red light on your Jaguars center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.

Part two: Now it is time to utilize the Learn function on your Genie garage door opener. Press the Learn button on your Genie garage door opener. The red LED adjacent to the Learn button will begin to flash. You now have 30 seconds in which to program your Jaguars opener button. Using the same button you just used in the part 1 procedure, press and hold the same button for several seconds. As before, your Jaguars red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center buttons red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguars remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguars remote button confirms to the Genies rolling code that your Jaguars signal is legitimate and is to be trusted from then on.

Posted on Dec 23, 2009

swolfinor
  • 504 Answers

SOURCE: program the garage door opener the Built-in car remote

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Posted on May 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remote door opener


So, you get out your remote control to your garage door opener and, then get your owners manual to your new car. You need to follow the instructions from the manufacturer to be able to program the remote control to the car.

Ok, you have followed the instructions from the car manufacturer and you press the button for the garage door to go up.......and nothing happens. So, then you think you have missed a step on the programing. Well, what most instruction manuals leave out is the step from programing the car/truck/van to the garage door machine itself. On the back side of your garage door opener is a panel called the logic board. The logic board is the computer or brain of the machine. Most new garage door openers now are a mulit-code machine. By that, i mean it uses several signals each time you press the button on your remote control. This is for security, so your code can't be stolen by a code-grabber.

Now, comes the step of programing the vehicle to your garage door opener. Once you have followed the instructions of programing your vehicle, you now have to "teach" the car to the garage door opener. You will need some help doing this. You will have to get someone to press the button in your vehicle and hold it down, while someone else has to press the learn button on the back your your garage door opener mounted on the ceiling. The learn button on the back of your machine will be square if using a liftmaster machine. Craftsman, Liftmaster, Chamberlain are all the same. Their learn buttons are square, and usually are yellow, red/orange, or purple. If using a Genie, it has a button that says "learn button".

The person pushing the button on the machine will only have to push and release the learn button. DO NOT hold this button down. If you do, it erases all of the programing in the machine, and you have to re-program all the remote controls that you have. You will have to read my other hub to find out how to do that. You will probably say a few words you shouldn't either. :-) Programing the vehicle to the machine only takes a second, and when the machine accepts the code, the light bulb on the machine should flash for a brief moment, and you should hear audible click. Yep, it's that easy! I dont know why the auto makers leave that step out. Anyway, i hope this helps, and if you have any questions.. leave them in my comments and i will try to walk you through it. See the photo above and you will see the typical logic board...the square red/orange learn button is easy to see. Just remember to press and release

May 08, 2012 | 1995 Lincoln Town Car

Tip

2010 BMW 528XI Garage Door Opener Homelink Setup


**** >>> This setup I performed with my new 2010 BMW 528XI Garage Door Homelink and Chamberlain Garage Door Opener <<< ****

Chamberlain:
01. Power off or unplug the garage door opener motor power supply (which is mounted on ceiling of the garage) ;;;

02. keep the garage door opener transmitter in your hand (do not press any button at this time) ;;;

03. In your 2010 BMW 528XI Homelink button (which resides under rear view mirror) press the 1st and 3rd homelink button together for about 30-40 seconds (i.e., until the yellow light blinks fast) and when the yellow light next to the homelink button blinks fast release from pressing the (homelink) buttons ;;;

04. now hold the garage door opener transmitter closer (means within 2-4 inches) to the homelink button (either 1st or 2nd or 3rd) whichever you are planning to program to open the garage door ;;;

05. now press the garage door opener transmitter button and chosen homelink button (either 1st or 2nd or 3rd whatever you need) together ;;;

06. the yellow light (next to homelink button) initially may blink slowly but after few seconds (may be 10-20 seconds) will blink fast; once it started blinking fast release from pressing both garage door opener transmitter and homelink button ;;;

07. Now plug or power on the main garage door opener motor (which is mounted on garage ceiling) ;;;

08. On the main garage door opener motor (which is mounted on garage ceiling) press the "LEARN" button (once you press it may have yellow/orange color light; make sure the light is on) ; then within 30 seconds do the next steps #9, #10, #11 very carefully ;;;

09. go to your car and press the homelink button you programmed and hold it for 4 seconds and then release it --> 1st iteration ;;;

10. again hold the same homelink button you programmed and hold it for 4 seconds and then release it --> 2nd iteration ;;;

11. again hold the same homelink button you programmed and hold it for 4 seconds and then release it --> 3rd iteration ** important note; generally three iterations are not necessary; and steps #9, #10, #11 must be performed within 30 seconds ** ;;;

12. during one of the iteration you will hear "CLICK" sound one-time from Garage door motor (which is mounted on ceiling) and if you have light attached with it; it will blink once (** if you hear the CLICK sound and/or light blinks once**) then the particular homelink button is programmed ;;;

13. now press the programmed homelink button; the garage door will open or close (but always it will take 3 or 4 blinks in yellow light or 2-3 seconds before the garage door opens or closes and which is normal) ;;;

** Thats it, your 2010 BMW 528XI Garage Door Opener Homelink setup is complete ** ;;;

You can program rest of the homelink button the same way but following from the steps between #4 and #13 ;;;

Hope this steps will help you to program chamberlain Garage door opener in 2010 BMW 528XI Homelink. ;;;


** possibly the above same steps may work with other BMW 5-series cars homelink too (but I'm not sure) **

on May 29, 2010 | BMW 528 Cars & Trucks

1 Answer

Attempting to set my 2002 suburban garage door opener with my remote opener how is this done


First you need to program the car with garage door remote, then program the garage door unit to the car. Hold Down garage door remote button and button of your choice in the car, the small light on the car will blink when it has learned it's code. Then press program button on garage door unit , within 15 seconds press and hold the button in the car that you programmed , when the the light starts to blink again, it should work.

Jan 14, 2011 | 2002 Chevrolet Suburban

2 Answers

What garage door opener is programable with a Mountaineer? I had an opener in my previous home that the sales rep programmed from the remote...my current door remote cannot be programmed. I am buying...


Press and hold the two outer buttons on the homelink system in the car until the led flashes rapidly or goes out. Then hold the programmed remote up to the homelink system and at the same time press the button on the remote and the button on the homelink until the led light blinks rapidly or goes out. It should take less than 30 seconds. ----- Then go to the motor head and press the colored learn button on the motor head and go back to the home link and press the homelink button 3 times to activate. If your opener has dip switches stop at -----. Thanks BB

Sep 17, 2010 | 2003 Mercury Mountaineer

1 Answer

? can i program remot control for the garage dor


Make sure you have a fresh battery in the garage remote. Drive away about a block and park. Press the two outer buttons on the IS for about 20 seconds , they will flash 10-15 seconds and then go out,erasing any old codes in the car.
Then select a button position, 1-2-or3 on the car for your garage function. Hold your garage remote to the car's button pad and depress the garage remote button and the cars button (1-2 or3)continually. The LED in the cars touch pad will flash slow, then fast then go out. Once these steps are completed the car and your hand held are syncronized...thh car has recieved the remote function. That is step 1 for all vehicles.

Now you need to return to the garage and "introduce" your car to the garage door opener's receiver. Depending on the brand there will be a "learn" button on the garage door opener. You will climb a ladder and push the learn button as per instructions in the opener manual or on the stickers on the opener motor itself, if it is a Chamberlain, Liftmaster or Craftsman....
These buttons will be pressed to erase old opener codes or program to add new devices...which is what your car is.
Each opener has its own series of functions but generally after initial set up of the ceiling unit, you will depress the learn button and hold for several seconds. Then within 30 seconds , you will depress the cars button for about 2 seconds and release, the lights will flash on the ceiling unit in the garage indicating success and the next time you press the cars button the system works.
For complete detailed instructions go to the HOMELINK web site. It covers most cars by model and openers by brand with VERY detailed instructions.
Nice car! Enjoy and post back with results



Jan 30, 2010 | 2004 Lexus IS 300

1 Answer

Can't program hyundai sonata to open garage door


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.



HOPE THIS HELPS

Sep 13, 2009 | 2008 Hyundai Sonata

1 Answer

Programing garage door openers


Press the button on the garage door opener (red, green, or yellow) until the led starts to blink and within 10 seconds or so, ( I think it's actually 30 seconds) press the GDO control button on the remote and the opener should capture the signal and respond to it from then on. Any remotes that were set to control the opener will be wiped and the new one will be in control. There are instructions that came with the opener that show how to do this from the remote or the key-less entry. If you are talking about an in-car device then your vehicle manual may be needed too, but the main thing is to set the GDO to be looking for the code from the car remote and when you press the in-car remote the garage door should respond. If you have programmed a remote or key-less entry then it is about the same procedure.

Jun 12, 2009 | 2008 Subaru B9 Tribeca

1 Answer

Setting garage door opener


Most openers are programmed the same. You normally program the house garage opener to accept the new remote. Your garage opener will have a button to press to add in a new remote. Normally you press this and then press the remote in the car and hold until your lights on your opener flash or the garage door closes. (check your manual on your garage door opener)

Mar 27, 2009 | 2005 Chevrolet TrailBlazer

1 Answer

Home link system will not accept garage door code.


I purchased a Chamberlain belt garage door opener. It was great! The lease on my duplex ended and the landlord bought it from me.

I found that the best way to program my vehicle's HomeLink buttons (to read the remote) was to do the learning procedure in a parking garage. This way the signal is not interrupted by all the waves around us.

Jan 02, 2009 | 2001 Lexus ES 300

2 Answers

Programming the garage door opener


I know what the problem is but never tried to resolve it. I have a 1998 XJ8 and went through the same problem. After numerous attempts to program the 4 channel built in opener I researched the problem and learned that the system in the car actually changes the code after every use. It's a security feature built in to the system. I simply started keeping my remote in the car.

There must be a way to disable the automatic randomizer so it retains the code from your remote opener everytime. Check with the dealer to see if it can be disabled and you will be in business. Please post the info if you get it.

Good Luck!

Nov 24, 2008 | 1998 Jaguar XJ8L

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...