Question about Cars & Trucks

Open Question

Misubishi l200 crank shaft pulley bolt torque setting

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: internationl 345 v8 torque settings

Head bolt torque: 90-100 ft lbs., to be reached in 3 equal tightening steps, below is the sequence:
9 3 1 6 8
Front of vehicle
7 5 2 4 10

Main bearing cap torque: 75-85 ft lbs.
Rod bearing cap torque: 45-55 ft lbs.
Looks like u've been busy, and will be for a while. Good Luck!

Posted on Nov 16, 2008

  • 1 Answer

SOURCE: Suzuki Vitara 1996 V6 2L assembly problems

The suzukiinfo.com site has a whole heap of free genuine manuals you can download and print out.
www.suzukiinfo.com

Posted on Jan 22, 2009

morse008
  • 1111 Answers

SOURCE: I need torque settings for 1600 beetle engine SP

wiki this

Posted on Aug 25, 2009

johnjohn2
  • 5763 Answers

SOURCE: TRYING TO RMOVE CRANKSHAFT PULLEY

yes, thats tone ring for crank sensor,car may run bad and trun on check engine light.good luck.

Posted on Oct 06, 2009

Testimonial: "INFO I NEEDED PROMPTLY."

  • 30 Answers

SOURCE: H23 92 Prelude - Crank Pulley fell off

Make sure you check timing and the belt. if it spun don't risk putting it back on. Hope you got a new key. TIMING is important so you don't stick a valve through the top of your piston

Posted on Oct 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for crank shaft pulley bolt on 1997 honda accord 2.2


the torque specs for the crankshaft pulley bolt on the 2.2 liter engine is 181 foot pounds

f3da1049-5f03-4476-b18a-1b251097af2d.png

Apr 25, 2015 | 1997 Honda Accord

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl


con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Dec 25, 2013 | Saab 9 Cars & Trucks

1 Answer

HAVE TO RESET THE TIMING ON A FORD FOCUS ZETEC SE 1.6 WHERE IS THE CRANK SHAFT LOCATION FOR THE TIMING PIN?


As you look at engine from timing belt side by where the drive shaft runs at back of engine around four inches back there is a small 10mm bolt that goes into the engine block undo this and that is where the pin goes don't forget that the crank pulley gear is free wheeling so make sure you use a new crank bolt and use correct torque setting

Sep 06, 2013 | 2003 Ford Focus

1 Answer

1997 acura tl crankshaft spinning freely, is this normal? Just replaced a/c compressor and the pulley is turning real slow. Belt is not slipping. The crankshaft pulley and a/c pulley/belt rotate normally...


CHECK SEE IF CRANK SHAFT PULLEY BOLTS LOOSE.IF CRANKSHAFT PULLEY LONG BOLT TORQUE IS FOR 130 FT LBS FOR 1.8L ENGINE. IF YOU HAVE THESE ENGINES CRANKSHAFT BOLT TORQUE IS 174 - 181 FT LBS ENGINES ARE 3.0L 3.2L 3.5L 2.3L 2.5L IF CRANKSHAFT PULLEY BOLT IS TIGHT.THE CRANKSHAFT PULLEY ITSELF BROKEN NEED REPLACING.

Sep 05, 2011 | 1997 Acura TL Series

1 Answer

1984 porsche carrera; I need the torque setting for the crankshaft fan pulley bolt.


Hello there
the torgue for pulley to crank shaft M12x1,5 is 80 nm (newtonmeters)......

proporsche

Aug 13, 2011 | Porsche 911 Cars & Trucks

1 Answer

What is the torque setting on the bolt that fastens the drive pulley to the crank shaft on a 98 Plymouth voyager 3.0 L engine.


Torque setting for harmonic balancer / pulley on the 2.5 and 3.0 engine is 132 ft/lbs

Please remember to rate this answer! Thanks, Mike

Jun 12, 2011 | 1998 Plymouth Voyager

1 Answer

Hi im fixing a 89 honda civic have everything to put it back together but the torque settings for mains,connector rod bearings head stage 1,2,3 an the rest thanks


CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

Mar 02, 2011 | 1989 Honda Civic

1 Answer

Bottem pulley on engine block is making noise, I think the bearings are going out. What is this pulley attached to and can it be lubricated?


the bottom pulley is the crank pulley. It is attached to the crank shaft. It has two parts, an inner and an outer that are joined together with a rubber isolator. Over time the rubber breaks down and the inner part part of the puller will start to rotate independently from the outer part of the pulley creating a unigue clacking noise.

To solve this you'll need a standard crank pulley puller set. You'll remove the crank bolt and then use the pulley puller to pull the crank pulley off of the crank shaft. The install the new pulley making sure to torque the crank pulley bolt to the proper spec.

Nov 06, 2010 | 1998 Buick Park Avenue

2 Answers

Hyundai elantra 1.6GLS J2 torque settings


dear friend:here follows the settings in need:
cylinder head-30-35 nm + 30-35 + 65deg + 65deg.
mains-30nm +65deg
big ends- 1 - 26nm 2 - 52NM
fly-wheel -130nm
cam-sprocket - 100-120
crank-pulley - 170-180
cam caps -15nm

Aug 31, 2009 | 1995 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...