Question about Cars & Trucks

1 Answer

Travira serve over counter

How to assemble

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 16,575 Answers

Do you have the model etc

Posted on Jul 29, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I got served with a counter suit, she is asking to reserve the right to be heard in superior court because she wants more than we can get in small claims court, can she do this??

No legal issues on this forum. Too many variables like what state/country you are in. The original case accusation and few here are qualified to give you particulars. Now if you had a problem with a computer or a Tacoma I might be able to help more

Apr 04, 2015 | Cars & Trucks

2 Answers

Tail light assembly replacement on a jeep Cherokee 1999

usually just a few screws and maybe a clip then remove assembly

Mar 27, 2015 | Jeep Cars & Trucks

1 Answer

Engine vacuum diagrams

in the USA?
open hood. look up, see that manditory EPA sticker with vacuum map
if missing? has it , and can vary by, USA FED or USA Calif.
if not USA then only the FSM covers this.
the factory serv. man. (go to dealer and ask at the parts counter , bingo)

Jul 07, 2014 | 1999 Isuzu Rodeo

2 Answers

How do you replace the front turn signal on a 2005 Buick Terraza?

Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

Sep 07, 2010 | 2005 Buick Terraza

1 Answer

Changing headlight on 2006 VW passat

Hello, to change the headlight on your passat, follow this steps:

1. Pull off the air intake cover, and remove the intake mounting bolt and set the intake hose aside,(passenger side only).

2. Twist off the protective cover from the back of the headlight assembly. Press the tab to pull off the electrical connector.

3. Turn the bulb socket counter clockwise to unlatch, and then slip it away from the assembly.

4. Turn the old bulb counter clockwise to release from the socket .Install the new bulb by turning it clockwise. Hold the plastic base of the new bulb when installing . Touching the glass can cause it to prematurely fail.

5. Insert the module and turn it clockwise to lock it in the assembly. Reattach the electrical connector and twist the protective rubber cover unto the back of the assembly .

6. Reattach the intake hose (passenger side only) and tighten the bolt. Snap the plastic intake cover back on.


Aug 12, 2010 | 2006 Volkswagen Passat

1 Answer

How do I remove the manuel locking hubs from my 1990 Ford F250 I removed the snapring from the end of the axle but the body assembly still will not slide out. How do I get the body assembly to slide out of...

If my memory serves me correct, I believe you need a special socket to do that. It's a long diameter round socket with small tabs around it.

Mar 14, 2010 | 1990 Ford F250

3 Answers

How do you get to the taillight bulb to change it

Here's a great video that will show you how to remove the taillight bulbs through the trunk.">

Sep 29, 2009 | 2002 Chevrolet Monte Carlo

1 Answer

I have as break light out, and would like to know how to replace it.

pull the screws out of the assembly and remove the light assembly, the screws are in the lens or on the back side of the light in the bed once you remove it you can twist the bulb socket counter clockwise and pull out the bulb socket and the bulb has to be pushed down on and twisted counter clockwise. If it's the front you will see screws in the front to remove. If you need more help reply to this post.

Sep 01, 2009 | 1995 GMC Sonoma

1 Answer

Brake light, 2008 Nissan Sentra

Open the trunk and locate the trim door that covers the back of the drivers side tail light assembly. Open the door and locate the bulb holder. The bulb holder can be removed from the tail light assembly housing by turning counter clockwise 1/4 turn. Holding the bulb holder in one hand, press gently on the bulb and turn then bulb counter clockwise to remove. Replace with a combo bulb and reverse proceedure to re-install.

Jun 21, 2009 | 2008 Nissan Sentra

1 Answer

2002 Tahoe stop light bulb replacement

yes, remove the two screws, and firmly yet carefully pull the taillamp assembly back out of the quarter panel. Once you have the taillamp out of the body and in hand, the sockets (on the back of taillamp) must be rotated to remove them from the lens. If memory serves, they must be rotated counter clockwise to release the socket from the lens housing, however, they will ONLY turn one way. plug your bulb into the socket and reverse the process. will only take about 5 minutes.

Dec 09, 2008 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides